similar to: Bristuff 0.20RC3 loses connectivity after short line interruption?

Hi list! I have some strange problems with Asterisk 1.0.5-BRIstuffed-0.2.0-RC5. Very regularly asterisk seems to lose connectivity with the ISDN line. If you try to call in you get the information tone that the number is not in use. Outbound calls do stil work however. Unloading the modules and reloading them and start/stop asterisk will solve the problem. Another problem that occurs

Hi list! I'm currently using a HFC-S card for my ISDN BRI line with bristuff. The instability is driving me crazy however. I'm having continuous problems where inbound calls will not work after some time of operation (the number then appears as not in use to the caller) or also outbound calls do not work. The solution is to unload the modules, stop asterisk, re-load the modules and

Hi list! I'm trying to install bristuff on a newly installed box. The box is running a rebuild of RedHat Enterprise linux with the latest kernel. The architecture of the box is x86_64 (Athlon 64), the os is 64 bit with 32 bit compat libs installed. Also the kernel source is installed as well as the (kernel) development tools. The bristuff install.sh script downloads asterisk+zaptel 1.0.2

Hello all. Since half december we are trying to implement * as our primary PBX. We had a test machine running with 2 sip phones and a single ISDN card. Since this was working ok, we installed * on our main Debian server. Some specs: P4 2.8 Ghz HyperThreading 512 MB RAM Debian Sid updated every week. Linux 2.6.9 vanilla kernel (not the debian package) 1 Intel Pro 100 nic for internal network 2

Hi list! I'm still trying to figure out about the groups in asterisk. If I understand correctly, if you assign a certain group number and you assign the same call group number to a sip device the device will reing even though you did not specifically specify it in extension.conf? How will this work for ISDN BRI/PRI? I don't want some extensions to get all calls from the BRI/PRI, just

After upgrading a CentOS 3.x box to CentOS 4.1 (both x86_64 with an Athlon64) I also wanted to get the latest bristuff. Unfortunately bristuff without florz causes the box to kernel panic within hours (console will complain about bad frame received something). It seems however that the florz patch will not work for x86_64 arch. Bristuff -0.2.0-RC8j compiles fine without the florz patch, but

Hello, I've added a ZAPHFC card to my CAPI based system. Calls coming in via ZAPHFC do not forward the caller id to the SIP phones. Calls coming in via CAPI do forward the caller id to the SIP phones. Any and all help is greatly appreciated. The (hopefully relevant) conf file excerpts are: extensions.conf =============== exten => 807440,1,Answer exten => 807440,2,Noop exten =>

Caller id is not in the configs that are supplied with zaphfc from bristuff, and it's not mentioned in the wiki. Is it possible to use callerid with zaphfc/bristuff? Thanks!!

I applied the florz patch but my problems remain. Now I get all sorts of weird errors on the console and I cannot make outgoing calls. Incoming calls work as expected. I am using a single HFC-S card with BRI. Any clue what these errors below are? Ri = 44651 TEI msg = 3 TEI = 7f Ri = 3800 TEI msg = 3 TEI = 7f Ri = 42399 TEI msg = 3 TEI = 7f Ri = 42409 TEI msg = 3 TEI = 7f Ri = 22078 TEI msg = 3

Hi list! On a newly installed RHEL 4 box I'm trying to install bristuff-0.2.0-RC8n. Everything did compile but I am running into some problems with the zaphfc driver. First of all when I load zaphfc *before* zaptel (yes I know I shouldn't do that) I get a kernel panic and the box hangs. Not so nice, especially when you are trying to fix stuff from remote locations. But ok. Now for

hello, I have a asterisk box (Slackware 9.1.0, Linux 2.4.31) connected to a Ericsson Businessphone PBX on the internal S0 bus with HFC-S card and zaphfc driver - point2point mode -. --------- | TELCO | | BRI | --------- | | PBX external S0 -------- | PBX | -------- | PBX internal P2P S0 NT Mode | | HFC-S Card P2P TE Mode

Hi list! I am installing an * box that will be installed on a site with KPN BRI ISDN in The Netherlands. I am using bristuff fron Junghanns. Does anybody know the correct settings for this? I will not have internet access there which makes it harder to google around on location. switchtype = euroisdn is pretty obvious but what about these settings: signalling = bri_cpe_ptmp ; p2p TE mode

Hi! I'm trying to setup a Wildcard TE110P with a PRI in The Netherlands. I get a Red Alarm on the line. Is there any way of debugging this? I've tried some configs that should work but without success. Is there any way of telling if the cabling is correct or what else the problem could be? Thanks!! Remco

Hi list! While looking for the Snom 190 I found another phone, the Elmeg IP 290 (www.elmeg.de). Looking at the pictures & the specs they seem to be very similar beasts but the firmware is supposedly not interchangeable. Does anyone know the difference between the 2, do they work with Asterisk? The weird thing is that Elmeg has similar phones with the Snom look but they are ISDN only (no

Most people seem quite positive about Snom phones, I cannot share this opinion. The displays are dying quite often, and firmware is buggy. I have tried every firmware from 4.5 up to 5.x and 6.04 but keep having problems with phones locking up or rebooting during an ongoing conversation. REALLY annoying for a phone that is advertised / targeted as a business class phone

Hi list! I'm sure the topic has been discussed but I could not find what I was looking for. What would be the best / easiest VPN software solution. I would like to install vpn software on the * server for roadwarriors to connect to with laptops running windows. Ideally the vpn solution will not require any additional software on the client side but will use IPSEC. (Ofcourse call quality

Hi list! Sorry for this slightly off-topic message but does anybody know if the standard for ISDN BRI is the same in Spain as it is in the rest of Europe (or the Netherlands). Will a standard HFC-S card work?

Is it possible to rewrite caller id's? I would like to have sip phones appear by their local cid (like Henk <208>) but when they call out using the PRI I would like their full DID (MSN) to appear (like 0031201234567) I could ofcourse set callerid to the main phonenumber but surely there must be a better solution? Thanks!! Remco

Hi list! I have some sip phones and Sipura ATA 2000's. However after dialling a number I need to dial a # to control a device. When I dial # Asterisk kicks in and puts the call on hold. How can I change this? Thx!! Remco

I tried to get callerid working the normal way but the cid is never passed to the phone. It doesn't work untill I set SetCIDNum(0${PRI_NETWORK_CID}) in extensions.conf which I found in the wiki: http://www.voip-info.org/tiki-print.php?page=Asterisk+zaphfc Is this intended behaviour, or still a bug? It does work but it only shows one zero even though I have nationalprefix = 0