similar to: Question on behalf of a wannabe new list member

Problem: Zap Channels Disappear @ random intervals. (Channels have disappeared on both gateways twice this week). My Setup: I have 2 Dell 1850 Power Edge Servers - Configured as. P4 2.8Ghz 512 ECC Memory SCSI Array (2 Drives Mirror) Configuration is really simple the boxes are setup as PSTN termination gateways: (SIP/ZAP) - We are running a SER/Asterisk Hybrid. My asterisk

Hi list, Ive got a server with 6 ports on it (4+2 port card) we have a DS3 delivering all voice DS1's to us. Carrier has a trunkgroup for the first 8 span (we only have the first 6 plugged in right now). Everything works fine until we fail the primary D channel (D's are on 24,48) the secondary then picks up and outbound calls do not work, if we reboot Asterisk the D on 48 comes up and it

Okay, now I am really confused. I have two PRI's coming in from two different Carriers (QWEST and ELI), both of them are supposed to be setup to pass name and number on incoming calls. Problem that I am having is that I am not receiving inbound caller id name on either PRI, the only thing that both carriers have in common is that I am terminating into a DMS switch at the carrier.

Hi, I'm a lab manager / supervisor at our labs. We've had Asterisk in use for over a year directly hooked to the PSTN - a no brainer for configuration (although I had to fix some AT&T specific things in libpri). Right now I have two big challenges. One is to hook our box up lineside to a Lucent Definity G3R. Avaya is chasing this from their end, but we had the highest level of

We've been working for the past 2 weeks to get a new V400P working with our PRIs from the telephone company. We're trying to get the Asterisk server setup as a VoIP gateway for SIP and AIX. We can make SIP-SIP calls, but all calls from or to the PRI fail. This is the applicable entries from the Asterisk log (configuration files follow) for a call coming from the PSTN on the PRI. I

List, I have a TE410P (T1 mode, all PRI) and a T100P (fxoks, for fxs channel bank). I cannot seem to get the T100P to send any clock to the channel bank. I prefer that it use the same clock source as the TE410P, but it doesn't matter if it's not in sync just as long as it's there. The TE410P is configured 3x pri_cpe, 1x pri_net. The three cpe go to XO Sonus switch, the net to

I have just built a new system using an HP DL360G7 with a TE420 T1 card, and this is the first system using a generation 7 server. I'm not sure whether that is an issue or not. I am using Asterisk 1.2, and Zaptel 1.4.12.1 with patches for GEN5 of the TE420 card. I have successfully used this combination on several systems based on the DL360G6 and TE420(gen5), which have been in production for

https://bugzilla.mindrot.org/show_bug.cgi?id=396 Martin d'Anjou <point14 at magma.ca> changed: What |Removed |Added ---------------------------------------------------------------------------- CC| |point14 at magma.ca --- Comment #13 from Martin d'Anjou <point14 at magma.ca> 2008-12-13

We have install a DS3 with 28 DS1's we have an Adtran MUX breaking out the DS1's, we are trying to setup the system with 2 dchannels for each 4 DS1's. Everything looks fine when modprobe zaptel and wct4xxp and ztcfg -vvvvvv but when I asterisk asterisk it says: Aug 10 16:33:32 ERROR[8954]: chan_zap.c:6750 mkintf: Channel 24 is reserved for D-channel. Aug 10 16:33:32 ERROR[8954]:

I'm installing TE405P card. This is my zaptel.conf. -------------------------------------- span=1,0,0,ccs,hdb3,crc4 span=2,1,0,ccs,hdb3,crc4 span=3,0,0,ccs,hdb3,crc4 span=4,0,0,ccs,hdb3,crc4 loadzone = us defaultzone= us -------------------------------------- When i modprobe wct4xxp, -------------------------------------- PCI: Found IRQ 11 for device 02:0b.0 PCI: Sharing IRQ 11 with

Hi all I'm trying to configure a TE410P in Europe with three E1s and a T1 channel bank (already bought in the US) to receive and make calls through *. I managed to get the E1s to work, but I'm having trouble with the channel bank (a Rhino). I have tried the bank in spans 1 and 4 changing jumpers in the card (always with no PRI connected, as I have no PRI where I'm testing now,

hi all, when i start * all zap channels get ring signal so i get a huge number of incoming dummy calls when starting *. i'm using TE105P with 4 TA750 full fxo with latest CVS HEAD: zaptel.conf: span=1,0,0,esf,b8zs fxsks=1-24 span=2,0,0,esf,b8zs fxsks=25-48 span=3,0,0,esf,b8zs fxsks=49-72 span=4,0,0,esf,b8zs fxsks=73-96 loadzone=us defaultzone=us zapata.conf: [channels] context=incoming

Hi, Probably a stupid syntax problem.. but can't seem to make these files work for more than the first T1 (ok, if I comment out the 2nd, 3rd, and 4th span). Can someone proofread this for me? Thanks! ====================== zaptel.conf span=1,0,0,esf,b8zs bchan=1-23 dchan=24 span=2,0,0,esf,b8zs bchan=25-47 dchan=48 span=3,0,0,esf,b8zs bchan=49-71 dchan=72 span=4,0,0,esf,b8zs bchan=73-95

i'm trying to set up outboud caller ID on 3 polycom ip 500 phones. here is how i have them set up. each phone is using 2 lines, all registered to * phone 1 line 1 is registered using the DID, and the next 5 lines reg to 03152 03153 03154 03155 03156 from my understanding, the way the polycom configs are set, i have to put the 03152 in the reg.x.address field. and it seems that is where

Hello, I'm running Asterisk@home 2.5 asterisk 1.2.4 zapatel 1.2.2 libpri 1.2.2 on a Dell Poweredge 2850 (1 CPU) with a TE210P I have 2 t1 circuits using NFAS with dchan on 24 and no backup dchan. I am able to receive inbound calls on all channels and can only make outbound calls on channels 25-48. Attempting to make an outbound call on channels 1-23 results in congestion.

Hi all, I've got a TE410p connected via T1 to four channel banks (2 FXO and 2 FXS), no PRIs. Some users are complaining that they hear clicks and pops on the FXS lines, generally when they pick up the phone it's noisy. This happens only after a while, e.g. after a fresh restart of everything, all is fine but after some time these noises start appearing. From what I've read on the

I am having a problem with asterisk not being stable enough for production use. I have two cards, the digium TE406P, and the TE410P. The TE410P is the primary card that I am using but I would like to move to the TE406P for the echo cancellation and more flexibility of PCI slots available. General config info: 3 PRIs, configured as such: span=1,2,0,esf,b8zs span=2,0,0,esf,b8zs

hi folks. i recently setup an Asterisk system in Hong Kong. their phone company told me that their T1 PRI switch type is Primary-NTT. however in chan_dahdi.conf there's no such option. i have it set to national. it worked fine for a while, but now suddenly stop working. in coming call just keep ringing and didn't even show up on console. out going call hang up immediately with cause code

I have a box with 12 T1s (4 Te410P cards). The PSTN provider is reporting slips and ask me to update the clock source. I have my system.conf set as the following but when I run dahdi_scan only the ports on Card 1 are showing up with syncsrc=1 system.conf : span=1,1,0,esf,b8zs bchan=2-24 mtp2=1 span=2,2,0,esf,b8zs bchan=26-48 mtp2=25 span=3,3,0,esf,b8zs bchan=49-72

Any ideas? 51] logger.c: [chan_zap.so] => (Zapata Telephony) Sep 28 00:42:35 VERBOSE[5151] logger.c: == Parsing '/etc/asterisk/zapata.conf': Sep 28 00:42:35 VERBOSE[5151] logger.c: == Parsing '/etc/asterisk/zapata.conf': Found Sep 28 00:42:35 VERBOSE[5151] logger.c: == Parsing '/etc/asterisk/zapata-auto.conf': Sep 28 00:42:35 VERBOSE[5151] logger.c: == Parsing