similar to: OT: Linux routing with T100P problems

Displaying 20 results from an estimated 2000 matches similar to: "OT: Linux routing with T100P problems"

2004 May 21
5
T100P HDLC configuration
All, I am trying to configure hdlc support on T100P Digium card - everything seems ok... but it just does not work at all. I was able to compile all drivers, the light on the card becomes green when I plug T1 link.... but I even can't ping default router IP... there is no data coming back to me, so I am confused completely now. Also I tried both protocols - raw hdlc and cisco hdlc. The
2004 Oct 02
1
Compiling HDLC does not Produce hdlc0 for T100p
my target is to produce a linux router with T100p to Fract T1 24chan to ethernet and TDM 4channel FXO. I have not been able to get nethdlc to work, just get zaptel networking not configured if I set bchan and dchan the card comes to life, but I don't believe this is correct for what I want to accomplish. according to markster@ this is the way they do it. using (multiple distro versions
2004 May 14
2
Data through T1, nethdlc
Hello all, My set up is a fractionated t1, with 1-6 voice channels, 21-24 data channels. I have a t100P installed in a amd 1500 with 512meg. Question: In order to set up the data channels, is the following correct? 1) compile new kernel with generic hdlc support 2) compile hdlc from hq.pm.waw.pl/hdlc 3) uncomment KFLAGS+=DConfig_ZAPATA_NET in zaptel makefile 4) compile zaptel, 5 compile rest
2004 Jun 07
1
hdlc setup routing question
Hello All, I am battling a problem I don't know how to fix... Here is the scenario: Fractionated T1 with 1-6 channels voice, 21-24 channels data. Comes into a box with Digium T100P, splits off data channes with HDLC, to devicec pvc0, This works fine, but I have a routing problem getting to my machines! Here is the current set up... sethdlc hdlc0 fr lmi ansi sethdlc hdlc0 create 44
2003 May 05
1
FW: HDLC & T100P
I got it figured out now. In case anyone else comes across it - this is what I had to do: Sethdlc hdlc0 mode ansi Ifconfig hdlc0 up ***NO IP INFO SET*** Sethdlc hdlc0 create <dlci number> Ifconfig pvc0 <local ip> pointopoint <remote ip> up Then set your default gateway to the <remote ip> listed in pvc0. That's about it!! Hope it helps! -----Original
2004 Oct 06
3
T100p half-height PCI bracket
Hello, Does anybody know of a place to get a half-height PCI slot bracket for the Digium T100P card? I have an application to fit them in 1U cases for small, deployable PBX's. The T100P itself is short enough to fit in a half-height slot but I need an appropriate mounting bracket to screw it into the case. Thanks, Mark Hagler
2004 Jun 29
2
T100P-E100P circuit board differences
Hi- Perhaps someone with an E100P in hand can answer this: I just received an E100P from Digium (I normally buy quad boards) I noticed that the circuit board says "T100P" on it, and I assume that the T100P and E100P both use the same circuit board. Can someone please confirm that their E100P says "T100P" on the artwork? Thanks Scott Scott M. Stingel Emerging Voice
2003 May 05
0
HDLC & T100P
I'm setting up a T1 for both voice and data and was wanting to know the steps involved. I've recompiled zaptel for ZAPATA_NET support and setup my /etc/zaptel.conf: Fxsks=1-10 Nethdlc=11-24 Modprobe wct1xxp works fine and my voice lines work. Now when I use the provided sethdlc, I use the following commands: Sethdlc hdlc0 mode ansi Ifconfig hdlc0 <ipaddress> <network>
2004 Oct 04
3
motherboard for T100P
anyone have a recommendation for a place I can buy cheap motherboards that supports those 64-bit 3.3 volt PCI slots for the T100P ? I can't find them at Fry's or anywhere locally. All I can find online is dual processor server boards that are overkill for this application. I would like to use a P3/ P4/ AMD single processor. No Xeons or dual processor junk. Anyone know why digium
2004 Jan 08
3
T100P positional on PCI bus?
I'm about to install a second T100P card in my asterisk system, and now I'm wondering how the system determines span-1 vs span-2. Does the position on the PCI bus determine this? TIA Mike
2003 Oct 10
8
T100P & Phones Configuration
Below you will find, what I believe to be a typical setup with a T100P card. My question is - 1. Is this correct? 2. What kind of phones would be needed here... (Would you have to use Digital phones) And if so what would you recommend. PRI/T1----- | | | ---------------- | | | Channel Bank | | |
2004 Jan 11
1
possible solution to PRI T100P dropped call issue
To recap: T100P card wouldn't sync with the telco using line side clocking ( span=1,1,0.........) Had to use internal clocking (span=1,0,0.......) zttool showed Tx/Rx Levels as 0/ 1 For the grins of it I replaced the T100P card with another newer card from inventory. This newer card has the same rev on the ASIC / FPGA but doesn't have any of the various jumper headers installed
2004 Aug 22
3
asterisk T100P to Merlin Legend
Management just approved purchase of a Digium T100P and a T1 card for our Merlin Legend Switch. I will appreciate comments from anyone performing this installation before: - Which T1 card did you use in the Merlin Legend? - Did you require any special interface? (CSU/DSU, etc) - Any items to watch during installation. Also we will need to remove one of our old analog Trunk cards to accomodate
2004 Dec 23
4
RedAlarm (t100p - Adtran Total Access 750)
Skipped content of type multipart/alternative-------------- next part -------------- No virus found in this outgoing message. Checked by AVG Anti-Virus. Version: 7.0.298 / Virus Database: 265.6.4 - Release Date: 12/22/2004
2005 Mar 08
2
Connect asterisk on classic pbx with T100P card
Hi, I try to connect my asterisk box with a classic pbx (Siemens). I have a T100P E1 card. modprobe zaptel and wct1xxp ok ztcfg -vv ok I can run asterisk and show the channels but the led still flash red My zaptel.conf : span=1,1,0,ccs,hdb3,crc4 bchan=1-15 bchan=17-31 dchan=16 My zapata.conf : ;; E1 switchtype = euroisdn signalling = pri_net group = 1 context=e1 channel => 1-15,17-31
2004 May 25
1
Problem - Adtran TSU 600, t100p
Hello, I have just received Adtran TSU 600 with 24 FXS ports. I have installed sucessfuly T100P card. Adtran is connected to t100p with crossover T1 cable. On T100P card I have a green light and on Adtran I do not get any errors or alarms. But I do not get dialtone on FXS ports. Adtran is configured: For Network Timing, fxs ports ore fxs_ls on Adtran. In zaptel.conf: span=1,1,0,esf,b8zs
2005 Jan 06
1
T100P + Adtran TSU600 + FXO and caller id problems
I have following setup Asterisk - T100P -> Adtran TSU600 P + FXOcard -> PSTN line When PSTN line is plugged directly in to analog X100P caller id is received by Asterisk but when I plug it into adtran I'm not getting caller id. Any ideas what kind of setup Adtran TSU600 requires to pass caller id to T100P ??? regards m.
2003 Oct 16
3
Adtran TA750 & T100P
Hello, So all the pieces are finally here, and I'm ready to play. I remember reading on this list that the connection Channel Bank <-> T100P requires a "reverse cable." Is this a regular Ethernet reverse cable (i.e., only a couple of pairs reversed?) Please help me before I blow something up! Saludos, Jose.
2004 Apr 21
3
T100P + Zap Errors
I am having some difficulty getting a T100P card to work with my PRI. When I attempt to make an outbound call via: exten => 1004,1,Dial(Zap/g1/NPANXXXXXX) I see the following on the asterisk console: -- Executing Dial("SIP/sbruton-b8ce", "Zap/g1/NPANXXXXXX") in new stack Apr 21 08:18:48 NOTICE[16401]: app_dial.c:554 dial_exec: Unable to create channel of type
2004 Apr 19
1
Playback problems with T100P
Hi, I'm seeing a problem when calling into my Asterisk server from a T100P with PRI signalling. I'm hoping someone has seen this as well, however, it's a little hard to explain. When I'm navigating through Asterisk on an inbound call from the PSTN, I'm getting a random 'noise' during the playback of sound files. The best way I can describe this noise, is imagining a