similar to: least sucky FXO interface?

Hello, Could anybody tell me if there is a Linux distribution (or Kernel version) that works better with Asterisk. I am newbie and I don't know if there is a preferred Linux/kernel version for Asterisk. Thanks. -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20040904/8798ff25/attachment.htm

Hi, I have the following scenario: We currently have 1 incoming line, that 2 POT phones plug into, and when we have an incoming call, both phones ring. Is it possible to have Asterisks in parallel, so that when the 2 POT phones ring, I can have a Voip phone, which "is" plugged in and configured through Asterisk also ring (so that all three of them are ringing), and then someone can

I have a nice used zhone channel bank I want to experiment with, but need a T1 interface for my * box to do so. The TE410P looks nice, but more money than I want to spend to experiment, and I don't need 4xT1, only 1xT1. Are there any good 1xT1 PCI cards that are recommended? Regards, -Dorn

Hi List, I am looking for a 1 FXO analog termination device, other than the obvious PC + FXO card, and which can achieve decent call quality. The SPA-3000 seems an option... have you got any other ideas? Cheers, Jean-Michel.

I'd like to get VM_CALLERID to include number in addition to name since often when calls come from cell lines or various other, the name is just a city, state and the number would be more usefull. Is there a way to get the number in the VM_CALLERID string, or is there a second variable I can use in formatting email vmail notifications to get the number? Regards, -Dorn

Hello , I learn handbook-draft.but I think I don't understand asterisk. where I can find some learning book about asterisk? thank u. B.R. John. -----????----- ???: asterisk-users-bounces@lists.digium.com [mailto:asterisk-users-bounces@lists.digium.com]?? asterisk-users-request@lists.digium.com ????: 2004?12?24? 7:51 ???: asterisk-users@lists.digium.com ??: Asterisk-Users Digest, Vol 5,

You can even set it to zero. Mine works well when in zero. The line pick up immediately :> -----Original Message----- From: asterisk-users-bounces@lists.digium.com [mailto:asterisk-users-bounces@lists.digium.com] On Behalf Of Chris Stenton Sent: Thursday, February 09, 2006 6:57 PM To: Asterisk Users Mailing List - Non-Commercial Discussion Subject: Re: [Asterisk-Users] SPA-3000 VOIP-PSTN

Hello All, I am trying to figure out which way to go for a quad port fxo solution with a good echo can on it. My options are the sangoma remora, a mediatrix fxo, or something similar. The issue is that I would need a good EC. This would be on about a 9000 foot loop, and the lines don't function well on a spa-3000 or zaptel tdm 4 port card. Anyone have experience that drives them in a

I just installed a new TDM400P with one FXO interface in slot 4 (how it came from Digium). This box is running Debian with a 2.6.10-rc2-mm3 kernel. After the make linux26 and make install in /usr/local/src/zaptel, I can see contents in /dev/zap but any attemp to touch for example /dev/zap/ctl gets a no such device or address ... Any suggestions?

If I have a call coming in on one line and then I am using Dial to send it out to another outside line, is there a good way to get separate CDR for both call legs? -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20060317/ac95b2fc/attachment.htm

Been using a few different FXO interfaces (X100P, Voicetronix, and SPA-3000) at a couple sites and they've all run into nasty issues at times. I'm looking at moving one of my offices and am in the market for a solution for connecting 4 FXOs. I got excited about recent offerings from Digium and Sangoma in the way of new cards but I hear they're causing troubles for more than a few.

Greetings, We are currently testing a Sipura SPA-3000 as a gateway from our Asterisk system to a PSTN line for 911 access. We have a number of locations and want to place an SPA-3000 in each, connected to a PSTN line that will provide the correct ANI/ALI information to 911 for each location. It all works great, except for a reasonably significant (4 seconds) delay between when the SPA-3000

Hi All, I'd really like to see a show of hands with regard to people's experience with FXO interfaces. I own a few X100p cards and have had nothing but problems with them. I also took part in Sipura's beta program, for the SPA-3000. While it can be an improvement over the X100p, it presently has echo problems that make it unusable. Sipura has not acknowledged the problem ( at least

Now I have searched around and not seen anything to do this. I want to in remote locations were we need to have single or 2 PSTN lines for in dial as little hardware as possible and as stable as possible so that they will operate without user intervention. What I want to do is be able to take a single PSTN line in and go out through adsl for the Inet link. These would be in VERY remote

I bought a couple of Mediatrix 1204's a few of months back. (Perceived advantages were relatively low overall cost and size per port, and it isn't nearly as vibration sensitive as a PC would be.) Rich Adamson's review from Feb 1 is comprehensive, and the only thing I'd like to add is this: One "feature" of these units that absolutely infuriates me is its behavior for

I'd dearly love to be able to give an Asterisk demo by just toting my notebook, a PC/PCMCIA card, and a couple SIP phones. Is there any way to do this? Or should I look for a small-profile box with PCI slots, instead?

Hello, I am trying to build up a pretty meaty Asterisk box after doing our initial testing and playing on a 1ghz system. Right now I have decided on a prebuilt system which I normally don't do but thought it seemed like a good deal. I have included the initial specs below, I will be adding another 1 GB of RAM for a total of 2 GB. My first question is regarding the serial ATA drives... I

My SPA-3000 finally arrived and I'm trying to get the FXO port on it to work as if it was a X100P card as far as Asterisk is concerned. I have Asterisk dialing out over the SPA-3000 FXO port no problem. The issue I'm having problems with is having the SPA-3000 automatically forward all incoming PSTN calls to the Asterisk "mainmenu" context (or ext I guess). Currently the

Anyone knows where can I find spandsp? Official site seems permanently down... TIA, Simone.

The USB core was completely rewritten in 2.6, and as such the functions that ztdummy depends on do not exist in 2.6. I get the feeling that these changes are too much to easily fix ztdummy, so I don't expect to see it working on 2.6 any time soon (if ever) I made some small changes to zaprtc to work on 2.6 and I have MoH and Meetme functions working fine in my lab. For production I would