similar to: Ethernet Channel Bank idea

I have had very bad experiences with IAXYs so far.. I have pulled them and will be attempting a refund shortly. Bad audio, overheating and shutting down until allowed to cool, etc. make it unusable in a business environment. That said, is there a low-mid priced solution for a remote office to connect to a home office runing asterisk? There seems to be a hole in the market for 6-8 person

Hello, I don't have any experience with channel banks and would appreciate any feedback on my theory outlined below: We have a single T1 entering the building with channels 1-12 being voice lines and 13-24 being a 768k internet connection. This T1 terminates to an Adit 600 (T1-1). Here's what I know. Channels 11-12 go out the Adit 600's 25-pair connector to a wiring block (and

Just starting my search for a SIP/MGCP/H323 channel bank. I need analog ports in a building that only have network connections back to my * server. I could install another * server and use a normal CB with a PRI but I would like to investigate any good CB's with network trunk abilities Thanks Dave Packham

Can someone recommend a good quality 24 or greater port channel bank? Steve -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20070506/e5896021/attachment.htm

Hello, I am working for a charity in the UK and I am projecting a new phone system. We would like to connect our two-wire telephones (40 or so) to an ADIT 600 channel bank, and connect that into an Asterisk box via the CMG card or T1 card. I have been in talks with Carrier Access about the purchase of a new channel bank and we tried to get a minor version of it first for testing with the

Jon, I actually had some more discussions with Tim on this issue, and it seems that the channel bank would still be a good option to choose for internal purposes. I would not see any other solution than a channel bank to connect many 2wire phones into one asterisk box. I had a talk today with Carrier Access, and it seems that the adit would do us fine. The fxs cards of the adit 600 are

I just picked up a couple CAC Access Bank 1s loaded with FXS that should be arriving shortly. Does anyone have one that they use with Asterisk? If so, would you be willing to shoot me a note with your current configs? I'm not very familiar with CAC/etc, and it would save me countless hours of muddling through .. :) Any others tips you can give me on these banks would be very

I have never had to pick out a channel bank before but I'd like to use one with the Digium T-1 card to hook 8 analog CO lines to an * PBX. Is there a reference somewhere describing and comparing channel banks (old and new)? Can modern channel banks handle translating all the "new" analog signaling features into a T-1 format? For example, can it interpret the 1200 baud FSK

I am forklifting a Merridian option 51c with 112 Nortel Digital Handsets and 400 analog units. For the analog units I have quotes for 9 ADIT 600 48 port fxs units and 17 Rhino 24 port FXS channel banks. I have used neither. Which is the best choice? The price difference is not that great. I am looking at Citelinks 24 port Handset Gateway for the Nortel Digital units. (Any other suggestions

Need to add some fxs and fxo ports behind a fonebridge2 box any recommendations a channel bank Thanks Mark -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20070829/1131cad4/attachment.htm

Hi, Is there somebody using an Access Bank I with Asterisk that could share the secret ingredients needed to make it work ? I've searched around and found some info, I tryed almost every configuration possible but I can't seem to find the right combination. If someone could provide me with the config needed on Asterisk as well as the dip-switch settings on the channel bank part, I would

So, I'm still having this problem with outbound calls not working when using a channel bank. I've purchased a Rhino FXO channel bank from VoIPSupply.com to make sure it wasn't an equipment problem. I am using a Digium TE411P card, and have simplified it down to just 1 port plugged into the channel bank, with just 1 analog line plugged in. If I place an inbound call on the line, it

I'm looking to buy a channel bank. I'll be using this to basically dual a Toshiba PBX and Asterisk so that we can deploy Asterisk in small steps and have the Toshiba as a fallback in case something goes wrong. What I need is a channel bank that will allow me to take in 12 lines using the FXO ports in the CB and then output those lines to the Digium T100P. Has anyone had experience

Hi all, I'm currently evaluating ideas for a phone system for our new office and I have a copy of Asterisk along with a couple of H.323 phones setup in the lab here. I'm very impressed - thanks for the great software! (I was especially impressed that the IAX connection to Digium worked out of the box like that - someone at Digium no doubt has a voicemail from me this morning!) ;-) What

I know a few ppl have those CAC Adit 600's with t400 I can't seem to get my second span up on the T400 connected to the second spand on the adit (A:2) A:1 seems ok Can someone post they zaptel.conf span defintions And maybe a "print config" from the adit 600 cli I think my issue is timing srcs the coding, framing. bld out are all matched thx -------------- next part

Folks, I'm experimenting with bringing multiple (8) analog lines from our local telco into a Carrier Access ADIT 600 channel bank with an FXO module, then having this talk to Asterisk via the T1 TDM controller on the ADIT and a TE405P card. I don't know if this will work well (ie: give me decent echo cancellation, call disconnect supervision, caller ID etc) but I haven't had much

Hi, I am supportive of the asterisk, but I have some concern, though the concern also applies to traditional pbx as well. Hope someone can shine some light into it. Thanks. During a power failure situation, analog pstn lines that connect directly to the analog phones will most likely still be able to make and receive calls. However, for the Asterisk implementation, unless you have a

I am experimenting with an asterisk setup in my office. The last bit I have to test is working with analog lines. I have TE411p digium card, with an ISDN line plugged into the first, a channel bank plugged into the second port, and the last two ports empty. I have the following setup in my zaptel.conf: span=1,1,0,esf,b8zs bchan=1-23 dchan=24 span=2,0,0,d4,ami fxsks=25 And in zapata.conf, I

Hello, I have an Adit 600 (3 FXS cards) hooked up to a digium T1 card in my asterisk box. I 'connected' the slots to the a:1 T1 interfaces via the command line. The slots (3 fxs) are configured with 'ls' signaling. I configured the T1 card with the same line settings as the T1 interfaces on the adit and I get green lights on both the T1 card and the T1 interface on the adit (so

Skipped content of type multipart/alternative-------------- next part -------------- A non-text attachment was scrubbed... Name: smime.p7s Type: application/x-pkcs7-signature Size: 3115 bytes Desc: not available Url : http://lists.digium.com/pipermail/asterisk-users/attachments/20060323/c0928576/smime.bin