similar to: E1 configuration problem

About every hour I see the yellow alarms on all or a number of channels of my PRI which is connected to the dutch telephony network, Asterisk keeps on working fine.... Here's an example where channel 1-24 went into alarm: WARNING[90124]: File chan_zap.c, Line 4139 (handle_init_event): Detected alarm on channel 1: Yellow Alarm WARNING[90124]: File chan_zap.c, Line 4139 (handle_init_event):

Hi Guys, I have several * servers connected to T1 PRI's from various service providers in multiple locations the US. All the * servers use the same hardware with the same OS and * version. When connected to 5ESS Switches, using the NI2 (national) PRI protocol, the CID name and number come across fine and populate into the * CDR fine. I connected to a DMS-500, NI2 (national) protocol and

Hi all, I?ve ran into a problem regarding D-channels. I have setup Asterisk (CVS-HEAD-03/21/05-16:41:57) on RH Fedora Core 3(2.6.10-1.770_FC3) I also have a digium wcte11xp card for connetivity to the PSTN(E1). When I start zttool i see that Current Alarms changes between Recovering and Blue Alarm/Recovering. I started to see these problems after i moved the digiumcard from one PCI slot to

Hi.... Apologies for the length of this, but any help would be greatly appreciated ;-)... I have installed and configured a Digium E100P on my Asterisk PBX and I have connected this to an 8 port E1 VoIP gateway on a Cisco 6509. There is also an external E1 link from our Telco plugged into one of the other ports on this gateway and this gateway is in turn registered with a Cisco CallManager

Hi, I'm installing E100P for isdn pri line. My configuration are like this. zaptel.conf ======================================= span=1,0,0,ccs,hdb3,crc4 loadzone = us defaultzone=us bchan=1-15 dchan=16 bchan=17-31 zapata.conf ================================================= [channels] context=default switchtype=euroisdn context=default signalling=pri_net usecallerid=yes

Hello all, I got a problem at an asterisk server, with dropping calls, losing all channels and reaktivating all channels and beeing back up. This problem seems to occure randomly over the whole day, when it gots traffic on the card. After looking @ google I found several hints but none did work fine. To avoid problems with the phone line (german E1) I called the provider, he did a 45 min. route

Hi, I hope someone can help me with this.... Asterisk 1.0.6 Zaptel 1.0.6 Libpri 1.0.6, 1 Digium E100P card installed Panasonic TDA200 firmware v2.0.6 E1 Card Firmware 1.0.2 System is located in Australia, so as technologies go, I believe it is twist on the euro standard for the E1 signalling. Here is the situation. The TDA E1 card is set in cross over mode and I am using a functional

hi, I'm trying to configure my newly acquired TE410P card to work as 4 E1 spans. This is supposed to be a drop-in replacement to the earlier E100P card. However, on loading the zaptel module it gets configured as T1 spans basically doing a 'cat' on /proc/zaptel/1 thru 4, it shows 24 channels per span. After this ztcfg fails saying 'ZT_CHANCONFIG failed for channel 97'.

Hello- After configuring DAHDI and starting asterisk, I get the following message continuously on the Asterisk console: WARNING[2057]: chan_dahdi.c:4158 pri_find_dchan: No D-channels available! Using Primary channel 16 as D-channel anyway! My card is a D410P configured for E1, only the first span is configured, and configuration snippets are as follows: From /etc/dahdi/system.conf:

Hi, I am having some problems mentioned below, the box is in production live environment with traffic around 30 - 100 calls. I am running T/E410P in a Dual P4 xeon with HT disabled. I am using zaptel 0.9.0 and asterisk stable 1 release. There is no gui, just mysql, perl (small script) and asterisk. System runs very smoothly if the calls are around 40-50 and comes one by one , however sometimes

In my efforts to solve a mystery of asterisk slowly loosing it's ability to take incoming and outgoing calls I set asterisk to restart b-channels every 60 seconds hoping I would find something odd after some time. So now I am looking at the CLI a few hours later and look what happens when asterisk restarts the 23 b-channels I have. pbx1*CLI> -- B-channel 0/19 successfully restarted on

Hi everyone, I have a PRI conection on an * system running Asterisk 1.0.9, libpri 1.0.9 and zaptel 1.0.9.2 connected to an AXE 10 (APZ 21220 System 64) in the network side. I know the system and the wildcard I´m using are ok because I´ve used them before with other PRI connections (to a Siemens EWSD) without any problem. First the PRI didn´t work (I got the TE110P alarmed with red). After

hello all, i'm using TE110P and all configuration prosess is done. but after i do the 'modprobe' for zaptel and wcte11xp, follow by ztcfg -vv and asterisk -vvvgc i have this error. *CLI> May 27 14:44:33 WARNING[3059]: chan_zap.c:8534 pri_dchannel: PRI Error: We think we're the network, but they think they're the network, too. May 27 14:44:34 WARNING[3059]: chan_zap.c:8534

Hello list, i've got some problems getting a E1 line with a E100P up and running (germany). # cat /proc/zaptel/1 Span 1: WCT1/0 "Digium Wildcard E100P E1/PRA Card 0" HDB3/CCS/CRC4 YELLOW RED "YELLOW RED" sounds not so good. When launching asterisk, enabling pri debug on that span, i see outgoing attempts: ;---------- snip -------- > [00 01 7f ] > Unnumbered

Hi all, I have 1 Card Digium TE412P and 2PRI E1. I have more problems with drops lines. The asterisk log is this: May 16 10:52:26 NOTICE[4465]: chan_zap.c:8194 pri_dchannel: PRI got event: Alarm (4) on Primary D-channel of span 1 May 16 10:52:26 WARNING[4465]: chan_zap.c:2287 pri_find_dchan: No D-channels available! Using Primary channel 16 as D-channel anyway! May 16 10:52:26 NOTICE[4465]:

Hola! I've a Digium E1 card, zaptel recognizes it as (loading the module with debug=1) Setting up DMA (write/read = 321b2000/321b2200) Controller version: 43 Framer: DS21554, Revision: 5 (E1) Found a Wildcard: Digium Wildcard E100P E1/PRA Using CCS/HDB3 coding/framing with CRC4 120 Ohms Calling startup (flags is 4099) Started DMA Got interrupt: 0x0005 /etc/zaptel.conf:

hi guys, I have a little problem maybe you can help ... I have an asterisk setup, with an E100P, and an ISDN-PRI 30 channel line from the telco going into it .. the E1 line is OK, because plugged into a Lucent Portmaster 4 it works OK .. plugged into the asterisk box I just get an engaged tone, and asterisk posts this message on screen : WARNING[1167272000]: File chan_zap.c, Line 5275

Hi! For demonstration purposes I try to bridge an incoming video call from a 3G mobile handset to another 3G mobile handset using asterisk as "switch". On the incoming call leg I see all expected bearer capabilities (Digital, 64k Transparent, G.7xx 384k video) but on the outgoing call leg the bearer capability G.7xx 384k video get lost and therefore the call is dropped from the mobile

<P>hi Everyone,</P> <P>We are configuring an ISDN PRI E1 with an E100P card, when you load the drivers, and starts the asterisk, cards also starts fine, givin following output,</P> <P>*CLI> <BR>&nbsp; == D-Channel on span 1 up<BR>&nbsp;&nbsp;&nbsp; -- B-channel 1 successfully restarted on span 1<BR>&nbsp;&nbsp;&nbsp; --

Skipped content of type multipart/alternative-------------- next part -------------- Console logs from Asterisk A: Executing Dial("SIP/test0-5821", "Zap/6/327557670||Tt") in new stack -- Requested transfer capability: 0x00 - SPEECH -- Called 6/327557670 -- Zap/6-1 is proceeding passing it to SIP/test0-5821 -- Accepting UNAUTHENTICATED call from 195.66.73.122: