similar to: Non-working module on TDM400P?

Hi all, I'm trying to install a TDM400P card, and I need some help. Please, see below... after dmesg command: [root@voip root]# dmesg via82cxxx: board #1 at 0xD800, IRQ 5 Zapata Telephony Interface Registered on major 196 PCI: Found IRQ 3 for device 00:09.0 PCI: Sharing IRQ 3 with 00:10.1 Freshmaker version: 71 Freshmaker passed register test Module 0: Installed -- AUTO FXS/DPO Module 1:

The REV I card shows up in the PCI table as: 02:05.0 Network controller: Tiger Jet Network Inc. Intel 537 (or 02:05.0 Class 0280: e159:0001) Subsystem: Unknown device b119:0001 But the REV E/F shows up as: 02:0d.0 Communication controller: Tiger Jet Network Inc. Tiger3XX Modem/ISDN interface (or 02:0d.0 Class 0780: e159:0001) Subsystem: Unknown device b100:0003 One

I installed the TDM400P and installed it on a system running on Fedora Core1, please refer to the steps below. I connected an analogue phone to the FXS port. When I pick up the speaker I don't hear the dialtone although when I press a number key I hear a DTMF generated. What could be the problem? I appreciate your help 1- First I installed the TDM400P in the PCI slot and connected

I apparently have a dead FXS module. Is there any kind of test I can run on it (on a live system) to determine if its good or bad? The telephone has no dialtone, gets no calls. It has been working for several months, and just quit yesterday. Thanks! Found a Wildcard TDM: Wildcard TDM400P REV I (4 modules) Freshmaker version: 73 Freshmaker passed register test Module 0: Installed -- AUTO

I have a TDM400. Just updated Fedora 12 to kernel 2.6.32. Rebuilt and installed dahdi-2.2.1. kernel modules loaded. lsmod | grep wctdm wctdm 37233 0 dahdi 194985 1 wctdm lsmod | grep dahdi dahdi 194985 1 wctdm crc_ccitt 1549 2 dahdi,isdnhdlc dmesg: dahdi: Telephony Interface Registered on major 196 dahdi: Version: 2.2.1

Hi all, I have just purchased the DevKit from Digium and received a X100P and a TDM400P (it has one FXS module). The problem is that I can't get the kernel module (wcfxs) to load and run. I have searched the archives and can't find anything about this. Do the messages below ring any bells with anyone ? There is no interrupt clash (see pci list below). I am running on a AMD 1.2G

Greetings all, I'm new to asterisk... Finally got two IP phones and two TDM400P's (one with four FXO modules and one with four FXS modules)... Began experimenting a couple days ago and have ran into a very aggrevating problem. My system consists of the following hardware: Abit BL7-RAID motherboard Pentium 4 1.6GHz processor 512MB SDRAM 2 TDM400P cards 2 3Com 3c905

I am having trouble with chan_zap.so not loading. When I load it from modules.conf, Asterisk bails out without any error message. When I load it from the console, it just says "Unable to load module chan_zap.so" no matter what verbose level I am using. dmesg says: Zaptel Version: 1.4.4 Zaptel Echo Canceller: MG2 Freshmaker version: 73 Freshmaker passed register test Module 0:

From asterisk -cvvvvv == Parsing '/etc/asterisk/chan_dahdi.conf': == Found == Parsing '/etc/asterisk/users.conf': == Found -- Automatically generated pseudo channel [Nov 11 17:43:28] WARNING[5756]: chan_dahdi.c:18155 process_dahdi: Ignoring any changes to 'userbase' (on reload) at line 23. [Nov 11 17:43:28] WARNING[5756]: chan_dahdi.c:18155 process_dahdi:

hi, i have problem with pass-through faxing with this scenario hylafax(iaxmodem) - iax - asterisk1 1.2.22 - sip - asterisk2 1.2.X(xen virtual) - linksys ATA i can fax to fax2mail on hylafax but after upgrade asterisk2 to 1.4 faxing is not working hylafax(iaxmodem) - iax - asterisk1 1.2.22 - sip - asterisk2 1.4.X(xen virtual) - linksys ATA configuration is same do you hava any idea what is

I'm running Asterisk on a Gentoo box with the Zaptel 1.2.1 drivers. If I boot the machine without having the wcfxs module autoload, then install the module with modprobe, asterisk works just fine. If I boot the machine and autoload the wcfxs module, the module loads fine: > Jan 11 11:06:55 asterisk Zapata Telephony Interface Registered on major 196 > Jan 11 11:06:55 asterisk ACPI: PCI

Hi, I am struggling to get rid of a conflict on DELL 2800 : PCI Parity error (EB113 on the display) I am learning linux and asterisk as I go along, there might be obvious things I should know, but bear with me. >From demsg below my 2 digium cards installed are listed (no config or connections done to digium cards yet), the conflict is with the TDM400P card, without that card, in any slot, no

I have a small system based on one TDM400 card with - 2 FXO modules for incoming lines - 1 FXS module for one phone The system was working fine in the past. The motherboard was exchanged and during the switch, the phones line was rewired with a mistake and a incoming phone line was connected to the FXS module, and there was ringing voltage on the module. Now, the system kinda works but the FXS

I have a TDM21B (A new TDM20B that just arrived plus a X100M that I already had). This card sometimes works, and sometimes only the FXO module is seen. (correction to previous message that incorrectly listed X400M/S400M when I'm using only the single port versions of these modules (X100M/S110M). By "works", I mean all 3 modules have the green lights on the ports on and when

Hi i have buy a Digium TDM400P with 1 fxo modules TDM01B for connect my asterisk to a french analog line. In my zaptel.conf, i have: loadzone=fr defaultzone=fr fxols=3 when i load the module, i have in logs: Nov 24 06:13:40 gw kernel: Freed a Wildcard Nov 24 06:13:40 gw kernel: Zapata Telephony Interface Unloaded Nov 24 06:13:40 gw zaptel: Removing zaptel module: succeeded Nov 24

Hi all, I'm trying to install a TDM400P card, and I need some help. Please, see below... after dmesg command: [root@voip root]# dmesg via82cxxx: board #1 at 0xD800, IRQ 5 Zapata Telephony Interface Registered on major 196 PCI: Found IRQ 3 for device 00:09.0 PCI: Sharing IRQ 3 with 00:10.1 Freshmaker version: 71 Freshmaker passed register test Module 0: Installed -- AUTO FXS/DPO Module 1:

Hi, I recently installed a gentoo on a PC, purchased a TDM400 and installed asterisk. Kernel is 2.6.11-rc3 First, there seems to be a problem with my system: I must put the pci=routeirq to make the card detected. The modules are loaded ok (dmesg output) Zapata Telephony Interface Registered on major 196 ACPI: PCI interrupt 0000:00:08.0[A] -> GSI 16 (level, low) -> IRQ 16 Freshmaker

I have a TDM400P with one FXO module and two FXS modules in it. I also have a Wildcard X101P. After trying hard to get things working on various Intel computers, but having echo problems that made it not really usable, I decided to try it on some older PowerPC (Macintosh) hardware running Yellow Dog Linux. Things started off smoothly. Both zaptel and asterisk seemed to compile okay, and both

Hi, I am having some issues with a new server install in Singapore. Outbound calls work fine. Inbound calls are not picked up by Asterisk. Zaptel 1.2.25 and Asterisk 1.2.28 both built from source. libpri installed wctdm and zaptel load without error Jun 6 23:34:03 fs01 kernel: [211138.372933] Zapata Telephony Interface Registered on major 196 Jun 6 23:34:03 fs01 kernel: [211138.372937]

Hi , I have an asterix (1.2.7.1) box with 3 TDM400P and 10 FXO modules, and zaptel (1.2.5). The problem is that 6 modules can't be initaized and i get the folowing error: May 7 09:17:37 WARNING[7739] chan_zap.c: Unable to specify channel 9: No such device May 7 09:17:37 ERROR[7739] chan_zap.c: Unable to open channel 9: No such device here = 0, tmp->channel = 9, channel = 9 ztcfg output