similar to: ATA's

Hello all. I just received a TE110P and am trying to hook it to my Mitel 200SX has anyone successfully done this? My configuration is as follows. Asterisk -> TE110P ->Kentrox (csu/dsu) -> Mitel T1 Card. All I get is a blinking yellow on my TE110P card and an alarm on my Mitel. T1 card. Any advice would be great. Zaptel.conf span=1,0,1,d4,ami e&m=1-23 dchan=24

> Message: 1 > Date: Fri, 21 Jan 2005 17:38:27 -0600 > From: "Henry Devito" <hdevito@qwest.net> > Subject: [Asterisk-Users] SPA-2000 > To: "Asterisk Users Mailing List - Non-Commercial Discussion" > <asterisk-users@lists.digium.com> > Message-ID: <000d01c50012$4ea49f30$4300000a@homeacxa7jw2xn> > Content-Type: text/plain; format=flowed;

I have searched both the wiki and googled looking for a solution to a square key configuration. I need to have C.O. lines to appear on the buttons to facilitate a small office. All of the users can see each other and calls are put on hold and picked up by the other users instead of transferred. Has anyone done this? Can it be accomplished and how is it accomplished? Thanks in advance.

Check my reply to your last post. Use SetGroup and Checkgroup before sending the call to your agents. Robert Jackson -----Original Message----- From: Henry Devito [mailto:hdevito@qwest.net] Sent: Thursday, September 30, 2004 10:09 PM To: 'Asterisk Users Mailing List - Non-Commercial Discussion' Subject: RE: [Asterisk-Users] Queue Setup almost got it Ok I think I have the queue

Hi, I am on my next venture now, Need to set up 3 queues. I would like these setup using the agentcallbacklogin. Does anyone have an example of this? I have looked through the wiki , but all that did was confuse me. One of the problems I'm having is how do I configure my extensions.conf to dial the agentcallbacklogin -------------- next part -------------- An HTML attachment was

Hi, I have not implemented any of the spa-2000's yet. Do they work ok with asterisk? Is the 2000 capable of having 2 FXS extensions off each one or is it two fxs ports with the same extension?

I am hoping to replace my Nortel 8x24 switch with Asterisk. Right now my cabling comes from my outside phone box into my office and into a punchdown block and leaves the punchdown block as an amphenol connector which currently plugs into the Nortel swicth. A second amphenol connector them plugs into the switch and extends to another punchdown block that I believe carries the lines throughout the

Which sound file is the one you hear when you call voicemail and it says Comedian Mail? I can't find it in the sounds directory -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20050329/a007d73a/attachment.htm

Are their any good chooses for IAX Adapters? -Thanks

Has anyone had successfully installed more then two digium wildcards in the same machine? I'm going for four. thanks Shoval Tomer, IT Manager, SofTov Advanced Systems, Ltd. Office: +972-3-9230686 ext. 179 Fax: +972-3-9216642 Mobile: +972-54-8000200

To provide a reliable fax solution for users connected to a Asterisk 1.6.2.6 server i have tested a few T.38 capable ATA's: - Patton M-ATA - Grandstream HandyTone 486 - Fritz!Box 7170 I have tried Asterisk 1.6.2.6 compiled with SpanDSP-0.0.6pre17 and also Asterisk 1.6.2.6 with Fax for Asterisk installed. These Asterisk servers are connected to a Cisco PGW 2200 + AS5400XM. Sending fax

Lots of interest here for conferencing. I've probably convinced more people to start using asterisk@home for this feature than anything else. Can I input some suggestions; Need to change the rinky dink call icons (let me know if you need some better samples) Need to change the ability for a muted caller to flag they have a question and a desire to talk (I do a lot of mute all except 1 or 2

Before I go and try to write something myself, I'm curious if anyone has a script that they're using for setting and clearing the MWI on a legacy PBX. I need to pick up a Zap channel and dial #63XXX to set the MWI, or #64XXX to clear it, where XXX is the extension number. One complication is that I've got a couple dozen extensions to handle the MWI for, and only four channels to work

Does anyone know how the Linksys PAP2T ATA's can be mass provisioned? Documentation seems to be sketchy, even on the Linksys web site. Thanks, Doug. -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20070607/3f90695c/attachment.htm

In the past we have used Adtran Atlas 550's to break out FXS ports for devices like modems. The great thing about the 550 is that internally it is all TDM so there is absolutely zero latency. We are able to use ATA's for faxes and analog phones but devices that use modems, they fail 99.99% of the time when using an ATA. We tried to migrate to TA908 devices; they have FXS ports built

I'm in the process of turning up a PRI in one of my markets and have run into a problem I have never seen before. I am unable to place a local outgoing call. Long Distance over the same PRI works fine. When I attempt to place a local call using the PRI I see Asterisk attempt to dial, and am greeted with a busy signal. This signal appears to originate on the telco's switch. I have had

I was doing a daily make update for asterisk. On the 19th the new version compiled fine. I installed it. All of my ata 186's can call out to pstn etc. All inbound calls, the phones ring but when you pickup, just silence both local and remote with no complaints in the cli. I backed down to the r 1.0 1.0.3 on the 20th CVS-v1-0-12/20/04-18:24:52 it worked ok. Yesterday I did a cvs update on the

Hi all, Happy Wednesday! Got a 7940G off eBay to tinker with and, per the wiki, contacted Cisco about a service contract. Being just little ol' me, they won't deal directly and blew me off (I hate dealing with Cisco, Nortel, etc as a small-business person...) Again per the wiki, I hit CDW.com and found CON-SNT-CP7960 for $9.14. Looking for support for the 7940 (not 7960), I just

We have the following available for sale. All equipment tested with a 90-day warranty. (150) CP-7960G refurbished $270/ea (20) CP-7960G new $305/ea (20) CP-7940G new $260/ea (50) CP-7905G new $140/ea (200) CP-PWR-CUBE new $25/ea (50) ATA186-I1 refurbished $130/ea (arriving next Monday) Let me know if we

Phil I have very good experience with the vegasteam ATA's devices.(you might also want to look @ sipura ATA's, since vegastream is doing an oem on there boxes) They support modem until v.90 speeds and faxes for g3. They are expensive, and again, work great and configure very easy joash ________________________________ From: asterisk-users-bounces@lists.digium.com