similar to: Newbie - Troubles after installing e100p

Hi, I buyed a wildcard e100p and I installed that but when I load asterisk I have this error: Apr 29 18:59:25 WARNING[8192]: chan_zap.c:690 zt_open: Unable to open '/dev/zap/channel': No such device Apr 29 18:59:25 ERROR[8192]: chan_zap.c:5403 mkintf: Unable to open channel 1: No such device here = 0, tmp->channel = 1, channel = 1 Apr 29 18:59:25 ERROR[8192]: chan_zap.c:7526

Hello list , I?m putting to work a new asterisk box. I?m running * 1.0.3 with (one ) Wildcard TDM ( 2FXS* 2FXO) and (one) E-100P. Both boards are working well. ztcfg don?t show me any error. zttool list both cards as "OK" But when i run asterisk on verbose mode i get those errors : [chan_zap.so] => (Zapata Telephony) == Parsing '/etc/asterisk/zapata.conf': Found --

I've put a t100p in our * server and I'm having trouble configuring it. It is directly connected to an Adtran TA 750 channel bank with two FXO cards (8 analog incoming lines total). I'm able to insmod and modprobe both zaptel and wct1xxp with no trouble, but when I start * with /usb/sbin/asterisk -c I get the following output: [root@rosella root]# /usr/sbin/asterisk -c Asterisk

Greetings I was getting bad static crackle on a phone, so I reload from the latest CVS and did a make clean ; make install on zaptel, libpri and asterisk Now I get this error [chan_skinny.so] => (Skinny Client Control Protocol (Skinny)) May 28 13:59:42 WARNING[16384]: chan_skinny.c:2541 reload_config: Unable to get our IP address, Skinny disabled Urgent handler [chan_oss.so] => (OSS

Trying to config the latest Asterisk/zaptel with an Digium Wildcard and a single X100m FXO interface connected to a POTS analog line. Build and install of both work ok - I'm using Suse 8 on a dual Pentium box. I load the driver with "modprobe wctdm" and the LED on the wildcard lights up. Then I start Asterisk with "asterisk -vvvgc" and asterisk fails to start. The

Hi List, I have a test asterisk box with a TDM400P with 4 FXO modules plugged in. Yesterday I could use the box without any issues - no problems. This morning, the sound on the box was absolutely horrible. After some fiddling about, I have rebooted the box, and now asterisk refuses to start! Here's the message I get: Jun 9 10:45:53 WARNING[3297]: chan_zap.c:769 zt_open: Unable to

After emerging some updates this morning asterisk 1.0.3 fails to start I get the following errors: ..Jan 6 00:39:24 WARNING[28998]: chan_zap.c:765 zt_open: Unable to specify channel 1: No such device or address Jan 6 00:39:24 ERROR[28998]: chan_zap.c:6197 mkintf: Unable to open channel 1: No such device or address here = 0, tmp->channel = 1, channel = 1 Jan 6 00:39:24 ERROR[28998]:

Hello, This is debug output I get: Jul 28 15:05:49 WARNING[8249]: chan_oss.c:239 sound_thread: Read error on sound device: Resource temporarily unavailable [chan_zap.so] => (Zapata Telephony w/PRI) Jul 28 15:05:49 WARNING[8249]: chan_zap.c:924 zt_open: Unable to specify channel 1: No such device or address Jul 28 15:05:49 ERROR[8249]: chan_zap.c:6460 mkintf: Unable to open

Hi all, i'm trying to install Asterisk with Junghanns QuadBri ISDN card: I have followed all the instructions, and when I run "|ztcfg -tvv" I get | | Zaptel Configuration ======================| SPAN 1: CCS/ AMI Build-out: 399-533 feet (DSX-1) Channel map: Channel 01: Individual Clear channel (Default) (Slaves: 01) Channel 02: Individual Clear channel (Default) (Slaves: 02)

Greetings all, I've just put two X100P cards to my box and despite trying everything I can find on the web, I can't get the second one to work. I've edited /etc/modules.conf so that ztcfg doesn't run automatically. To start, I run: /sbin/modprobe zaptel /sbin/modprobe wcfxo /sbin/ztcfg /sbin/modprobe ixj and ztcfg says: ZT_CHANCONFIG failed on channel 2: No such device or

All of sudden my FXS module is not working. I have a TDM card with one FXS and one FXO, FXO module seems working fine. I also noticed the LED is not on for my FXS module while it is on for my FXO module. Sep 13 12:11:44 WARNING[9870]: chan_zap.c:887 zt_open: Unable to specify channel 1: No such device Sep 13 12:11:44 ERROR[9870]: chan_zap.c:6612 mkintf: Unable to open channel 1: No such device

Hi, all I have installed TDM400 card. I can see it is there (lspci). But Asterisk does not find it. phonebox2*CLI> zap show status No Zaptel interface found. I assume that driver is not loaded, but I am sure I have installed it (I compiled zaptel and then re-build asterisk and did make install for both zaptel and asterisk). When asterisk is started I get: Jan 2 06:28:08 WARNING[3473]:

hello friends, I am configurin my Billion ISDN and when I start asterisk (asterisk -vvvc) I have this error message: [chan_zap.so] => (Zapata Telephony w/PRI) == Parsing '/etc/asterisk/zapata.conf': Found Apr 23 15:27:23 WARNING[2205]: config.c:525 process_text_line: No '=' (equal sign) in line 29 of zapata.conf Apr 23 15:27:23 WARNING[2205]: config.c:525 process_text_line:

I am trying to reconfigure an asterisk box that was using an HFC-S card with bristuff but is now using 2 analog lines therefore I want to use the TDM02B to connect to two POTS lines. The TDM02B has 2 red modules. I have this in /etc/zaptel.conf loadzone=nl defaultzone=nl fxsks=1-2 I have /etc/asterisk/zapata.conf signalling=fxs_ks echocancel=yes echocancelwhenbridged=yes echotraining=400

Hi all, i have installed two digium cards on my asterisk box a TDM04B & TDM22B. The channels are configured as show below: Channel map: Channel 01: FXO Kewlstart (Default) (Slaves: 01) Channel 02: FXO Kewlstart (Default) (Slaves: 02) Channel 03: FXS Kewlstart (Default) (Slaves: 03) Channel 04: FXS Kewlstart (Default) (Slaves: 04) Channel 05: FXS Kewlstart (Default) (Slaves: 05) Channel 06:

I have a new Sangoma A102 and I'm trying to get it running in asterisk. A look through the dmesg log shows the card is detected and the various channels created. However, when I start asterisk I get the error below. Any ideas? My zapata.conf is below. Thanks, MD == Registered custom function SIPCHANINFO == Registered custom function CHECKSIPDOMAIN == Manager registered action

Hola! I've a Digium E1 card, zaptel recognizes it as (loading the module with debug=1) Setting up DMA (write/read = 321b2000/321b2200) Controller version: 43 Framer: DS21554, Revision: 5 (E1) Found a Wildcard: Digium Wildcard E100P E1/PRA Using CCS/HDB3 coding/framing with CRC4 120 Ohms Calling startup (flags is 4099) Started DMA Got interrupt: 0x0005 /etc/zaptel.conf:

Hi, I have two WCT100P cards installed on a suse 9.0 box. Installation for Zaptel complains of some unresolved dependencies. The zaptel and wct1xxp modules load without any errors. ztcfg give no problems. The problem is when I start asterisk I get the following error and asterisk shuts down

Of course I am not a kernel expert, so .. please be patient. I am investigating on my zaptel/zapata problem. As the main error message asterisk quits on mentions <'/dev/zap/channel': No such file or directory> I went peeking over there. [Asterisk Verbose Error Mar 13 20:43:35 WARNING[5779]: chan_zap.c:763 zt_open: Unable to open '/ dev/zap/channel': No such file or

Hi, I've a little problem with my asterisk server. I have managed an asterisk server for a few months one. Today, I wanted to restart it and when I did it, my asterisk server didn't want to start again. I looked at the various messages in /var/log and the same thing appears. " [chan_zap.so] => (Zapata Telephony) == Parsing '/etc/asterisk/zapata.conf': Found Sep 30