similar to: T100P Configuration for Mixed Voice & Data

I've been having some problems getting a channelized T1 working with a T100P card. Perhaps someone can help: I have an Eschelon T1 coming into a Vina Integrator box. This box splits out the T1 into an ethernet plug for bandwidth and a secondary T1 which I plug into the T100P card. I've connected the two with a T1 crossover cable. I get a green light on the t100p card and can make

I'm considering switching my incoming phones lines from standard analog to a T-1 service from XO communications. They propose to bring in an "IAD" which has 12 lines of voice and 768k of internet bandwidth as part of a package deal. Since I want to keep the voice traffic in the digital domain the equipment they're proposing is a "Lucent Digital Vina Integrator" IAD

Hi, I am fairly new at working with Asterisk. I am having a call quality issue that I really need to get ironed out before we go to rollout the system in a week. Any help would be greatly appreciated!!! Even if it is just pointing me in the right direction. My current setup: I have Asterisk Setup on a Dell Server. It has 2 T100P cards. One will be for out T1 PRI from the Phone Company (We

Has anyone tried a Vina T-1 Integrator as a channel bank with Asterisk? They appear to be plentiful, but I want to make sure I'm not buying a brick. THX/BDH

I got it figured out now. In case anyone else comes across it - this is what I had to do: Sethdlc hdlc0 mode ansi Ifconfig hdlc0 up ***NO IP INFO SET*** Sethdlc hdlc0 create <dlci number> Ifconfig pvc0 <local ip> pointopoint <remote ip> up Then set your default gateway to the <remote ip> listed in pvc0. That's about it!! Hope it helps! -----Original

I'm setting up a T1 for both voice and data and was wanting to know the steps involved. I've recompiled zaptel for ZAPATA_NET support and setup my /etc/zaptel.conf: Fxsks=1-10 Nethdlc=11-24 Modprobe wct1xxp works fine and my voice lines work. Now when I use the provided sethdlc, I use the following commands: Sethdlc hdlc0 mode ansi Ifconfig hdlc0 <ipaddress> <network>

Dear I have a data.frame, and want to fit a constrained non-linear model: data: x y -0.08 20.815 -0.065 19.8128 -0.05 19.1824 -0.03 18.7346 -0.015 18.3129 0.015 18.0269 0.03 18.4715 0.05 18.9517 0.065 19.4184 0.08 20.146 0 18.2947 model: y~exp(a)*(x-m)^4+exp(b)*(x-m)^2+const I try to use nls() and set start=list(a=1,b=1,c=1,m=1), but which always give me a error message that

All, I am trying to configure hdlc support on T100P Digium card - everything seems ok... but it just does not work at all. I was able to compile all drivers, the light on the card becomes green when I plug T1 link.... but I even can't ping default router IP... there is no data coming back to me, so I am confused completely now. Also I tried both protocols - raw hdlc and cisco hdlc. The

As a follow-up to my previous post where I stated the IAD would be a Vina model, after some more prodding to XO, they have told me it will either be an Adtran TA-600 or a CAC Adit 600. These products are covered pretty well on the web and I have manuals on both. So, if those knowledgeable folks had to use one of these to attach to an Asterisk box, what interface would be best or at least

Hello Astrites, I was just about to send out a long email about not being able to detect hang-up with my CAC II FXO module on my PSTN POTS lines. I had tried many configurations. I had attached a toner to the line to see if I was getting this "disconnect supervision" signal after hang-up. (toner has a line powered light in the off position) It seemed that I was getting the signal,

Callerid issue 1) if you run ztmonitor on the fxo line & call in do you hear the fsk tone if yes then we beleive the CAC is passing fsk 2) in chan_zap->ss_thread around line 4154 (current cvs) if you get to the callerid_feed at least once then if you get to chan_zap->ss_thread->callerid_get around line 4163 (current cvs) does this parse fail

I am having a problem using the Adtran 750 FXO quad card with a Groundstart trunk line. I am able to receive calls on the trunk line, however dialing out is not working. The Adtran does not seem to be doing the signaling. Has anyone used the 750 FXO card in Groundstart mode? Any special configuration issues that I should be aware of? Syed Akbar Alico Systems Inc www.alicosystems.com Tel:

I am preparing to setup a system using Cisco 7940 and 7960's I have the 7.1 SIP firmware on them. One issue I have run into is how to silence the ringer if a call comes in and you don't want to take it. Many phones have a DND button. I know the 79XX has the DND in the menu but it is to cumbersome to go into the settings then phone preferences then the DND and select yes. Is there any other

hello, I just installed 2 brand new x100p cards into my linux system. Everything compliled and worked fine from the first try. Hoewver the phone lines I will use with this system have groundstart signaling. I have tried to change the zaptel.conf and zapata.conf to use this type of signaling but ztcfg gives me an error every time with the new configuration. Bellow are the config files and the

Don & others, Thank you for your answer. The fog maybe lifting ;). The zaptel.conf file has the following in its comments: # # The timing parameter determines the selection of primary, secondary, and # so on sync sources. If this span should be considered a primary sync # source, then give it a value of "1". For a secondary, use "2", and so on. # To not use this as a

(to mods: sorry for any extra work I've put you through. Posting from my work account, as proper) Hello all, I'm back. I've got that lucky feeling that this will all work out very soon, and I hope that that is true. The issue: In my * server I have a t100P, connected with a T1 crossover cable to an Adtran TA750 with 2 FXO cards. After I do 'modprobe wct1xxp;ztcfg' the alarm

Hi Folks, I have a T100P ordered from Digium in the past. Its working perfectly fine but I now need to more the server to India (out-sourcing) and we will be getting an E1 line there. Does anyone know if T100P was capable (upgradeable) or swappable so that I could use it with the E1 lines instead? Any pointers to driver/firmware update would be highly appreciated. Thanks. R -------------- next

I ran into a couple of odd problems with a new Asterisk box I have set up... I have a T100P connected to a channelized T-1 (24ch) to the PSTN. The T-1 is set up properly so far as I know and seems to work perfectly with one exception: When a call comes in, asterisk starts a 'simple switch' for it, goes through my 's' extension progression until it gets to the first Playback

Hello Everyone, I am new to asterisk and linux too, I managed to installed asterisk on redhat8 with the help of mailing list archives and Handbook guide. I configured 2 SIP phones (grandstream) and it is working fine internally. We have T1 Line coming in with block of 200 DID Numbers. I want to assign DID Numbers to each of SIP phones as an extensions and able to call any PSTN line.

Hello, So all the pieces are finally here, and I'm ready to play. I remember reading on this list that the connection Channel Bank <-> T100P requires a "reverse cable." Is this a regular Ethernet reverse cable (i.e., only a couple of pairs reversed?) Please help me before I blow something up! Saludos, Jose.