similar to: 2x HFC ISDN Cards - SuSE 9.1 - Problems with making calls

I'm not 'overly' new to asterisk, but I am very new to the Digium card / Telco aspect of it. I was able to get a TE110p card, installed.. and hooked a t1 up to it. I'm using zttool to just look at 'some' output. Here is what it looks like when I just load it up: Current Alarms: No alarms. ? ? ? ? Sync Source:

Hi, I have problem with X100P clone card.I can not force it to work under Asterisk 1.4.27.1 and DAHDI Version: 2.2.0.2. I looked over and over on configuration and could not see any mistakes. Here are relevant configuration files. /etc/dahdi/system.conf > fxsks=1 > echocanceller=mg2,1 > loadzone = hu > defaultzone = hu > dahdi_tool > OK Wildcard X100P

Hi Group, I have a problem with my FXO interface. It seems that asterisk cannot see any configured channels, only pseudo. Pls see the error and my config below. Rgrds Markus ----- May 2 15:09:00 NOTICE[17327]: app_dial.c:1010 dial_exec_full: Unable to create channel of type 'Zap' (cause 0 - Unknown) == Everyone is busy/congested at this time (1:0/0/1) == Auto fallthrough, channel

Hi, It seems like my ATA is making a ringing noise... (as it used to), but now (After the upgrade from 1.0.7 to 1.2) asterisk also is either making the ringing, or passing the PRI ringing from the telco on to me. Any suggestions on how to fix this?

I need some help getting a system running for one of my company's plants. I am running AsteriskNow 1.7 with Asterisk 1.6.2.10 and FreePBX 2.8.0.2. My D-Channel keeps bouncing. The telecom tech told me he thought that I might be using the wrong sync source, and I think I might have been, but I changed DAHDI system.conf to "span=1,1,0,ESF,B8ZS" (from

I have what my SBC/ATT representative calls a "Supertrunk," but he can't tell me the specifics I need to know to configure Asterisk to work with it. By fiddling about, I've come up with the "almost working" configuration below. This works except that it takes about 4 seconds from when the console says the line is answered until it plays my prompt. Watching the

Hi, I've been playing with a TE120P on Asterisk 1.4.18 with zaptel 1.4.9 and I've ran into an issue. After a call placed any DTMF tone causes the server to lock up entirely. Calls placed work just fine (except for a problem with echo cancellation). The phone registered to the server is a Linksys SPA-942. I am seeing in zttool some IRQ misses, but it never seems to go above 74 (below).

> I've never bothered to check to see if cat5 cables use the appropriate > mating twisted pairs or not. Since the pinouts are different for cat5 vs > T1 cables, I'd have to guess a single strand is used from two different > twisted pair groups. That wouldn't be cool, but in short runs it > probably doesn't have much of an impact. > IIRC, standard Ethernet uses

Hi all.. I`m with a problem in some E1 cards. The value of Bipolar Viol is too big, and some times the link seems well, but isn`t work correctly, like as if the link is down. Normally, I use to stop asterisk, remove the modules from my card, use modprove to set up they again, and start asterisk, and it come to work, but in some times I have to reboot the server, and then the value of

Hi, Bristuff works great with HFC card... your compilation problem may come from your kernel configuration... You should check this doc, at least, for the redhat config : http://www.automated.it/guidetoasterisk.htm Then, installation of Bristuff works like as charm ! Bye David Masure -----Message d'origine----- De : vdasilva [mailto:aquamoon@wol.co.za] Envoy? : mardi 28 juin 2005 09:01

Hello I have asterisk running in Red Hat 9 with a cheap HFC card on i4l. I have choppy sound problems sometimes, and echo problems often. I am using a 2 port Grandstream ATA, Grandstream BT and a Grandstream GPX-2000 I read that changing to BriStuff will fix the echo problems, but have also read other users say that the only way they solved the echo/choppy sound problems was using a Fritz ISDN

> Close. 10/100mbps Ethernet uses wires 1,2,3,6 but that is pair 2 & 3. > Pair > one is the pair up the dead center (pins 4&5), pair 2 is pins 1&2, pair 3 > is > 3&6 and pair 4 is 7&8. A T1 uses pairs 1&2, which is why you can't use a > regular crossover cable for a T1 crossover, but you can use a regular > ethernet patch cable as a T1 patch

Hello everyone. I've got this really annoying HFC Cologne card (or however I should call it - a single channel ISDN card based on the HFC chipset). It wrongfully detects lots and lots and lots of incoming DTMFs, to the point the card is not usable. Here's a sample out of CLI: P[ 1] I IND :DTMF_TONE oad:206361 dad:520101 P[ 1] --> mode:TE cause:16 ocause:16 rad: cad: P[ 1] -->

Hi, I would appreciate some advice on the following: how does one use a single BRI port HFC chipset based ISDN cards with the latest DAHDI, libpri and Asterisk 1.8? For Asterisk 1.4 I would first install mISDN & mISDNuser and then build Asterisk 1.4. Now I noticed that Digium's HFC chipset based B410P is supported by the latest DAHDI & libpri but reading the source of the

hi, i just found a page on the net which might me worth some lines. for the urgent reader: http://isdn.jolly.de there is a guy in germany who has successfully programmed a gpl-patch for isdn4linux to make isdn cards with the hfc chipset from cologne chip (http://www.colognechip.com) run in the NT mode (up to 2.4.20). this mode is needed to connect isdn device to a pc and enables the use of

Does any one put a HFC-S card working in nt ptp mode? -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20100221/ca845019/attachment.htm

I've got an old HFC-S card to play with, and I would like to use it in NT mode. I've a problem only: wiring. I can't fully understand the instructions I was able to find online. Someone can point me to a site which explains the whole procedure clearly (like with some schematics, even in ASCII)? TIA, Simone.

It seems so simple, but I'm having no luck installing a HFC-s ISDN BRI card on *@home 0.5. I probably have to install BRI-stuff from Junghanns.net but that also downloads and installs another copy of * from Digium. I'm not sure if zaphfc has to be installed *before* Asterisk or if it's OK to do this afterwards. I've seen this question before, but: Anyone successfully installed a

Hi, I have built another Asterisk box using one ISDN HFC-S card and Bristuff-0.2.0-RC8p. But this time it behaves very strangely. Asterisk simply hangs and in logs I receive something like this: --NOTICE [1197]: PRI got event: HDLC Bad FCS (8) on Primary D-channel of span 1 --NOTICE [1197]: PRI got event: HDLC Abort (6) on Primary D-channel of span 1 And when I want to call a ZAP channel I get

I've been trying to set up incoming faxes using spandsp with a HFC card. Unfortunately, incoming faxes are of very poor quality, the pages are not transferred wholly (sometimes only a bit of a page is transferred etc.). From what I've read, I may have troubles with correct "timing" (and need to set up ztdummy etc.). On the other hand, it is impossible to set ztdummy if one