similar to: Zaptel.conf and Zapata.conf for TDM12B

Hi- I'm totally stumped configuring my TDM400P with one FXS and one FXO module. Before I got the FXO module, I used to have an X101P, and everything was working very well. Now * doesn't seem to recognize the FXO channel. I've searched the wiki and the list archives. Stock Debian 3.0 stable installation. Any advice? Thanks. -- David Here's my configuration: modprobe zaptel

Hi , I have an asterix (1.2.7.1) box with 3 TDM400P and 10 FXO modules, and zaptel (1.2.5). The problem is that 6 modules can't be initaized and i get the folowing error: May 7 09:17:37 WARNING[7739] chan_zap.c: Unable to specify channel 9: No such device May 7 09:17:37 ERROR[7739] chan_zap.c: Unable to open channel 9: No such device here = 0, tmp->channel = 9, channel = 9 ztcfg output

Hi: I was running TDM12B. Both FXS and FXO were working fine. Then all of the sudden FXS had problems. When I pick-up the phone and dial any number, FXS doesn't respond. I just keep hearing the normal signaling line tone comming from the FXS. I changed the FXS module and it had the same problem. I changed the the TDM card and installed different FXS and nothing changed. I appreciate any

I recently updated (fresh checkout) to the newest zaptel and Asterisk. The one I was using before was a couple of months old. After updating, my zap channels don't work. They won't pick up incoming calls or dial out. When I try to dial out I get: -- Executing Dial("SIP/3064-564c", "Zap/g1/ww954.......") in new stack NOTICE[245776]: File app_dial.c, Line 698

I installed the TDM400P and installed it on a system running on Fedora Core1, please refer to the steps below. I connected an analogue phone to the FXS port. When I pick up the speaker I don't hear the dialtone although when I press a number key I hear a DTMF generated. What could be the problem? I appreciate your help 1- First I installed the TDM400P in the PCI slot and connected

I have a TDM400. Just updated Fedora 12 to kernel 2.6.32. Rebuilt and installed dahdi-2.2.1. kernel modules loaded. lsmod | grep wctdm wctdm 37233 0 dahdi 194985 1 wctdm lsmod | grep dahdi dahdi 194985 1 wctdm crc_ccitt 1549 2 dahdi,isdnhdlc dmesg: dahdi: Telephony Interface Registered on major 196 dahdi: Version: 2.2.1

I am having trouble with chan_zap.so not loading. When I load it from modules.conf, Asterisk bails out without any error message. When I load it from the console, it just says "Unable to load module chan_zap.so" no matter what verbose level I am using. dmesg says: Zaptel Version: 1.4.4 Zaptel Echo Canceller: MG2 Freshmaker version: 73 Freshmaker passed register test Module 0:

From asterisk -cvvvvv == Parsing '/etc/asterisk/chan_dahdi.conf': == Found == Parsing '/etc/asterisk/users.conf': == Found -- Automatically generated pseudo channel [Nov 11 17:43:28] WARNING[5756]: chan_dahdi.c:18155 process_dahdi: Ignoring any changes to 'userbase' (on reload) at line 23. [Nov 11 17:43:28] WARNING[5756]: chan_dahdi.c:18155 process_dahdi:

I have seen this in the archives any number of times -- but I have yet to find a solution that works for me. Any suggestions you can offer would be most appreciated. Here are the answers to the questions I have seen asked in earlier posts. The log contains: Mar 10 12:26:29 WARNING[3015] chan_zap.c: Unable to specify channel 4: No such device Mar 10 12:26:29 ERROR[3015] chan_zap.c: Unable

I installed Trixbox and a TDM400P with 2 FXO and 2 FXS ports and am having an annoying issue with the FXO ports. As soon as I plug either one into the phone line it's as though the line is disconnected i.e. get disconnected tone when trying to dial out, line is busy when dialling in. The CLI shows the following: trixbox1*CLI> zap show channel 4 Channel: 4 File Descriptor: 18 Span: 11*

Hi, I'm having problems using a TDM400P Card. I put my SIM card in a Nokia Premicell and connected it to a TDM400P card but when I make calls to the number, it hangs up automatically. The card also can't call out. Any ideas? I've searched the archives without much success. I appreciate all your help. Details: I'm using Asterisk 1.2.17 on Fedora Core release 5 (Bordeaux). On an

Hello all, This is my first post to this mailing list. I've been following the development (not as a developer, but as an interested user) of Asterisk for over a year now. It's only in the last month that we've decided to give it a try (hey, might as well...everything else we use is open source). We ordered a TDM11B (1 FXS, and 1 FXO). The card and Asterisk install was uneventful.

When I reload the config, I see this error in the CLI. However, I don't see what I have done wrong: == Parsing '/etc/asterisk/zapata.conf': Found May 30 16:38:42 WARNING[12630]: chan_zap.c:10088 setup_zap: Ignoring signalling -- Reconfigured channel 1, FXO Kewlstart signalling May 30 16:38:42 WARNING[12630]: chan_zap.c:10088 setup_zap: Ignoring signalling -- Reconfigured

I got this nice TDM22B with two green modules left and two modules right /var/log/messages shows: Nov 26 23:47:48 dns kernel: Zapata Telephony Interface Registered on major 196 Nov 27 00:37:53 dns kernel: Freshmaker version: 71 Nov 27 00:37:56 dns kernel: Freshmaker passed register test Nov 27 00:37:56 dns kernel: Module 0: Installed -- AUTO FXS/DPO Nov 27 00:37:56 dns kernel: Module 1:

Hi all, I've been running Asterisk with a TDM400P for about 6months, no problems. 2 in/outgoing analog lines, one analog phone. Recently I was messing with the XTEN client, got to finagling with things, and not knowing what was wrong I upgraded from 1.0.7 to 1.0.9 (both asterisk + zaptel). I was testing various things, and found everything worked except outgoing calls. So I checked

I'm afraid that I am at a loss here. I am new to Asterisk, and have successfully set up SIP. But I cannot get my FXS card working, and I'm not sure what else I can try. # modprobe wcfxo /lib/modules/2.4.21-37.0.1.ELsmp/misc/wcfxo.o: init_module: No such device Hint: insmod errors can be caused by incorrect module parameters, including invalid IO or IRQ parameters. You may

Hello Since TDM cards are known for being particular when it comes to motherboards (PCI 2.2, etc.), I was wondering if there is a utility that can check that the Zaptel driver works OK and can tell if the TDM card is compatible? That way, if an FXO module is not reporting an incoming call, we'd know it's because of the Zaptel driver, and not something elsewhere. Are "dmesg",

Hi all, I have hit a wall configuring a TDM400, I have set these up before without issue but today I just can't seem to figure out what I am doing wrong. On an incoming call the following is produced in the Asterisk console with verbose 4 -- Starting simple switch on 'Zap/2-1' Mar 22 16:12:34 NOTICE[2051]: chan_zap.c:6063 ss_thread: Got event 18 (Ring Begin)... Mar 22

Hi again, I'm trying to setup our non pri T1 (they call it a Long Distance T1), our current pbx has the signaling set to E&M, I can set em in zapata.conf, but I'm trying to track down the proper entries for the zaptel.conf file. The digium docs only show a PRI example. Our current system has these settings: Signalling: E&M Framing mode: ESF Line Coding: B8SZ here's my

(I'm producing a writeup on all the things one run into building an * box. Which after a couple of boxes is showing up aplenty.) So this uses the working h/w and config's from another box. All I do is build in a new computer. Loading the modules I got: __________________________________________________ Zaptel Configuration ====================== Channel map: Channel 01: FXS