similar to: libr2 status

hi! What's the libr2 status for Asterisk ? I've got R2 E1 delivered to my * box. I have TE410P digium quad card with newest CVS. How much % is completed with libr2 ? what's completed ? & What's missing ? Thanks, bit123.

I just came across libr2 anyone using it in its current state. Specifically someone from India or around India using it. Also does it work with the digium e1 cards or only the Dialogic cards. http://digium-cvs.netmonks.ca/viewcvs.cgi/libr2/ -- regards Vikram (http://www.vicramresearch.com)

TE410P card down. I have three (3) TE410P in one machine running asterisk with SS7. My problems started last week when one of my cards started switching to E1 every time after reboot. I set the following in dahdi.conf and that solve the problem. /etc/modprobe.d/ options wct4xxp t1e1override=0x00 Now all 4 ports on that card is down with Red Alarm. I tried rebooting the machine and

hi, I'm trying to configure my newly acquired TE410P card to work as 4 E1 spans. This is supposed to be a drop-in replacement to the earlier E100P card. However, on loading the zaptel module it gets configured as T1 spans basically doing a 'cat' on /proc/zaptel/1 thru 4, it shows 24 channels per span. After this ztcfg fails saying 'ZT_CHANCONFIG failed for channel 97'.

Hello All I need to use Asterisk with an E1 sangoma card with CAS R2 signalling for Vietnam what is difference between libr2 of CVS and libmfc2 of soft-switch.org ? how to compile chan_unicall.c on asterisk. asterisk update CVS-head- May 27 2005. Thanks -------------- next part -------------- An HTML attachment was scrubbed... URL:

Hi list, We have been trying to configure a Quad Span T1 card in a system running RH9. We have followed the instructions in the Wiki and searched the mailing lists, but so far havent got any success. Cable is connected to the first span, and module is loaded. Without loading the module the LED glows in red colour, but the moment we load module, it goes off. (No red or green) . We ran zttool

Thank you for response. So a "standard" quad bri card can serve the KX-TD1232, no need for anyt special fxs similar equipment. Would like not to invest much more money into the Panasonic, I wan't it out :P BR Amund -----Opprinnelig melding----- Fra: asterisk-users-bounces@lists.digium.com [mailto:asterisk-users-bounces@lists.digium.com] P? vegne av Peter Svensson Sendt: 14. juni

hi all, i've now installed a TE410P (Quad T1/E1 Primary Card - Digium) and connected it to a primary line. My telco (eTel) only told me that they are using hdb3 and crc4. So i still don't know which coding i have to use (cas or ccs) - and what timing options i have to use. Have someone already get a card like this up in Austria with a line from eTel or from the telekom Austria ? Another

List, I have a TE410P (T1 mode, all PRI) and a T100P (fxoks, for fxs channel bank). I cannot seem to get the T100P to send any clock to the channel bank. I prefer that it use the same clock source as the TE410P, but it doesn't matter if it's not in sync just as long as it's there. The TE410P is configured 3x pri_cpe, 1x pri_net. The three cpe go to XO Sonus switch, the net to

I have an * box connected to a Nortel SL100 through a PRI (US) using the Digium TE410P (quad-span T1 card). I don't have access to the SL100 - it is handled by another group. The span comes up OK (timing, framing fine). However, as soon as the D channel comes up, I get endless "HDLC Bad FCS" errors. I modified logger.conf to get rid of the messages (so I could see what else was

Hi, I found E400P quad PRI card quite cheap (749USD): http://www.govarion.com/product_info.php?cPath=1&products_id=2&osCsid=68cdd6e3d08754 in comparison to te410p (approx 1500 USD ) http://www.digium.com/index.php?menu=product_detail&category=hardware&product=TE410P Now newer generation with HW echo canceling emerged (te411p). I'm not sure in what things those two cards

hi! I have a question of ISDN PRI "calling number" setting for outgoing call. I need the receiver to see the CLI that I have set. Eventough I've set the CLI as below, the receiver keep on getting a fixed number( used with the PRI to receive incoming calls). My ISDN PRI E1 provider says he has not done any restricions on the custom CLI side.

I for one think it is a great idea to buy a book with hard earned money and wait a few days to a week just to get an answer to a question that is freely available on the internet immediately. Hard pressed to think of anything in the "book" that is not on with wiki with more up to date and useful information. -----Original Message----- From: Alexander Lopez

I've just encountered an odd problem with our Digium TE410P card and was wondering if anyone has experienced something similar before. We utilize all 4 ports with 2 of them connected to the PSTN as E1 with the second 2 ports connecting to a device which accepts T1. We are essentially acting as an E1 to T1 converter. This machine has been operational for close to 6 months without a problem.

Hi to all, I have a problem with this wildcard and one E1 line. The server is a Asus P4P800S with the 865PE chipset, and 512MB RAM. The kernel version is 2.4.26. I have donwload and build the latest CVS version of zaptel, libpri and asterisk following the ufficial instructions of digium. I have set up my server in this way: zaptel.conf loadzone=it defaultzone=it

<P>hi Everyone,</P> <P>We are configuring an ISDN PRI E1 with an E100P card, when you load the drivers, and starts the asterisk, cards also starts fine, givin following output,</P> <P>*CLI> <BR>&nbsp; == D-Channel on span 1 up<BR>&nbsp;&nbsp;&nbsp; -- B-channel 1 successfully restarted on span 1<BR>&nbsp;&nbsp;&nbsp; --

Hello, I am in Argentina configuring an E1 in R2 and have some inconveniences. When the call takes the salient line, I receive an error of signaling. In * I have loaded the following: - libr2 installed - The [ar] in zonedata.c and indications.conf is configured - zaptel.conf o: span=1,0,0,ccs,hdb3,crc4 span=2,0,0,cas,hdb3 #span1 bchan=1-15,17-31 dchan=16 #span2 cas=32-62:1001

<P>hi,</P> <P>Can anybody pls tell me how to activate loggin CDR on mysql db. I tried&nbsp;editing the /etc/asterisk/cdr_mysql.conf file and recompiling asterisk, it didn't work. Normal loggin on Master.csv file works fine.</P> <P>Thank you inadvance,</P> <P>Surajee</P> <P>&nbsp;</P><br> --------------This mail sent

I have 12 T1's going into 3 servers, 4 in each into "Digium, Inc. Wildcard TE410P Quad-Span togglable E1/T1/J1 card 3.3v (rev 02)" cards. Each "group" of T1's have the primary D on 24 and the secondary D on 96. The first server (ts20) and the last server (ts22) can playback "demo-congrats" fine. The "middle" server (ts21) cannot -- just dead air.