similar to: quadBRI

I installed the QuadBri card in my * server. I'm installing * on a RedHat 9 server I run the install.sh file. So far no problems. If I try to start /sbin/ztcfg -v -c /etc/zaptel.conf I will see the following error: Zaptel Configuration ====================== SPAN 1: CCS/ AMI Build-out: 399-533 feet (DSX-1) SPAN 2: CCS/ AMI Build-out: 399-533 feet (DSX-1) SPAN 3: CCS/ AMI Build-out:

Hi, I have Installed * on a DL380 with a Junghanns 4BRI card and 0.0.2 driver. I have 3 BRI lines connected to SPAN(TE) 1,2,3 and 2 Cisco 7960 with SIP image. I am connected to french PSTN (France Telecom) whith Euroisdn signaling. I manage to call SIP to SIP, PSTN to SIP but not SIP to PSTN. Any idea? Thanks Gwenn Gael Marronnier Here is what I get and my configuration...

Hi, I'm trying to connect quadbri between powered ISDN phone and ISDN line: ISDN <---1---> TE - * - NT <--2--> Phone I use quadbri, suse 9.2 and latest 0.2.0-RC7k bristuff. I've used sample settings provided with package, but do get strange error (I think that I have wrong setting for P2P or P2MP setting and cables 1 and 2). If I connect phone to ISDN with straight cable

Hi all, this time with the complete configuration files... We need help with our SuSe9.2 asterisk box We have one QuadBRI and one TDM40B in an ASUS pundit R-2 barebone. We have downloaded the bristuff (0.2.0-RC7j) and installed it without problems. once we downloaded and compiled asterisk, zaptel and all other stuff, the module installation succed in this order: modprobe zaptel modprobe qozap

Hello, We have a quadBRI in NT mode with bri_cpe_ptmp signalling and when connect a ISDN telephone to this nothings happen. What can I do? My config files are this: Zaptel.conf: loadzone=es defaultzone=es # qozap span definitions # most of the values should be bogus because we are not really zaptel span=1,1,3,ccs,ami span=2,1,3,ccs,ami span=3,1,3,ccs,ami span=4,1,3,ccs,ami bchan=1,2 dchan=3

Hello, I cannot make any call with my new quadBRI card from Junghanns.net in my asterisk box. My asterisk box is built on Fedora Core 3 linux system. After compiling drivers from junghanns.net the card driver was loaded correctly with - modprobe zaptel - insmod qozap.ko ( as FC3 is running a 2.6 linux kernel) - ztcfg -vvv ( shows 12 channels correctly configured and the 4 leds on the card were

Hi All ... I'm running Asterisk 1.2.13-BRIstuffed-0.3.0-PRE-1v which has a Junghanns QuadBri card in it (lspci reports Cologne Chip Designs GmbH ISDN network Controller [HFC-4S] (rev 01)) I have a regular KPN ISDN2 Line connected which works fine with the the zapata.conf below. However, I also have a new KPN ISDN Mutli (meervoudig) line (PBAX-Group), which works fine for incoming calls,

Hi all, i'm trying to install Asterisk with Junghanns QuadBri ISDN card: I have followed all the instructions, and when I run "|ztcfg -tvv" I get | | Zaptel Configuration ======================| SPAN 1: CCS/ AMI Build-out: 399-533 feet (DSX-1) Channel map: Channel 01: Individual Clear channel (Default) (Slaves: 01) Channel 02: Individual Clear channel (Default) (Slaves: 02)

Hi. I'm running some asterisk boxes on different sites, some equipped with a couple of ZapHFC cards, others with Junghanns quadBRI cards. All boxes were compiled with Asterisk 1.2.10 (libpri 1.2.3 zaptel 1.2.6) and bristuff 0.3.0 pre 1s, distribution is Fedora Core 4 with kernel 2.6.17.3 The cards are connected to Telecom Italia's NT1/NT1+ S/T lines; some of them are point-to-point,

I am running * with a Junghanns quadbri that should allow us to integrate our ISDN house telephone system with VOIP. Preferably I would like to run a setup, so that our internal ISDN phones on an S bus are not aware that * is sitting in between. With the configuration below I run into the following problems: 1. On outbound calls, I get the normal rining call progress tone althought the

Hi, I have a Junghanns QuadBri installed and seems to be detected and working correctly using the wcb4xxp driver All ports are configured as TE The problem is when I connect an ISDN line - the LED turns green and Dahdi status shows Alarm OK But when I try to make a call I get "All circuits are busy" cause 27 I have searched and web and tried numerous configs but it doesn't want to

Hello all, Recently I purchased an QuadBRI card from junghanns.net after some playing around, reconfiguring dialplans etc with the exception of 1 thing everything seems to work: I seem to be unable to set the outbound callerid. The dutch telecom operator (KPN) provided me with 4 MSN's on 1 BRI interface. In the past years I'm more then used to setting the MSN without the leading 0, this

Hello everybody, and first of all sorry for my poor English. I'm having trouble with Quadbri installed on Asterisk 1.2.17-BRIstuffed-0.3.0-PRE-1y-e. Everything is working fine, except calling to switched off or "out of coverage" cell phones. In this case I have to wait 40 seconds until Asterisk tell me that "all circuits are busy now" instead of receive cell phone

I am unable to make quadbri board to work in NT mode, in TE mode it works OK. I have set 5 jumpers to NT mode. Dmesg shows everything OK: qozap: Junghanns.NET quadBRI card configured at mem 0xd084e000 IRQ 9 HZ 100 CardID 1 qozap: S/T ports: 4 [ TE TE TE NT ] qozap: 1 multiBRI card(s) in this box, 4 BRI ports total. from Asterisk side seems to be ok. pri show span 4 Primary D-channel: 12 Status:

Hi- Anyone using the Junghann's quad BRI card and the Digium E100P in the same system? I'm having a configuration problem where I can configure the cards one at a time (with the appropriate drivers loaded) in a system, but when I try them both together, neither will work. They both work fine one at a time. Probably has something to do with the channel numbering. I've tried

Hi, I'm pulling my hair out, cause cannot connect to EuroISDN BRI in Italy with octobri card from Beronet. I use bristuff and have following zaptel.conf... # # This file is parsed by the Zaptel Configurator, ztcfg # # # First come the span definitions, in the format # span=<span num>,<timing>,<line build out (LBO)>,<framing>,<coding>[,yellow] # # The timing

Hi there, I am attempting to set up a simple BRI and SIP based platform using * with the quadbri card (it's not sharing an IRQ). I enclose my zaptel and zapata.conf files. For the inital test I'm simply trying to connect to the * demo menu. The drivers compile (with a few warning that I believe aren't important - see attachments). chan_zap comiles with the warning: chan_zap.c:

I got the same problem, and what i change it was point-to-point to point-to-multi-point, and I used normal patch cable to connect the ISDN card to ISDN connector, and I used TE mode. In italy work like that I hope that will help you, I used also bristuff. Good luck ________________________________ Da: asterisk-users-bounces@lists.digium.com [mailto:asterisk-users-bounces@lists.digium.com]

Hi all, We need help with our SuSe9.2 asterisk box We have one QuadBRI and one TDM40B in an ASUS pundit R-2 barebone. We have downloaded the bristuff (0.2.0-RC7j) and installed it without problems. once we downloaded and compiled asterisk, zaptel and all other stuff, the module installation succed in this order: modprobe zaptel modprobe qozap modprobe wcfsx then the ztcfg output this: Zaptel

Hi, we are using asterisk with Junghanns QuadBri and some sip phones. 2 channels are configured in NT mode (ISDN PBX connected, internal ) and 2 channels are connected to the public ISDN network (bri-cpe). We use Bristuff 0.2.0 RC8C from Junghanns. When a call comes in from the public phone for a specific extension (Hotline Number), we initiate a parallelcall to some SIP phones and also to our