similar to: Chan_Capi Down

Hi all, I'm new to asterisk and not too knowledgeable on ISDN, so please be gentle :) I have a dual-channel Eicon Diehl Diva card in a Debian Woody box with kernel 2.4.27, connecting to a Telstra (Australia) Onramp Home Highway ISDN line. I'm pretty certain the card and line both work since they've been used in this machine for PPP before this (but with an older kernel with DoV

Hi all ! We have 3 NTBAs which are all going to our existing PBX. Our areacode is 06003 and our DDI enabled number 9141. I want to exchange that PBX with Asterisk, but still struggle to get it working. My CAPI.CONF is currently like this: [general] nationalprefix=0 internationalprefix=00 rxgain=0.800000 txgain=0.800000 [interfaces] context=in-capi msn=60039141 incomingmsn=* controller=1

Hi, I?ve strange problem when I?m making a call from SIP (Cisco 7960) to capi (Fritz PCI). When I call a national number, I?m hearing the ringtone when the called party is ringing but when I call an international number, I don?t hear the ringtone and I?ve a silence until the called party answers. Both call are going through the same extension. Here?s 2 log files, one with a national number and

Hi all, i have asterisk 1.0.9 with an Eicon Diva 4bri and chan_capi-cm-0.6. I have 2 NTBAs (one with did and one without). When using the one without did, i am able to place outgoing and incoming calls. When i use the NTBAs with did i have a layer 2 error. Anyone an idea? -- Executing Dial("SIP/2004-9634", "CAPI/g1/43XXXXXX") in new stack > data = g1/43XXXXXX

Hi * Fans, I have some fritz cards now, followed instructions from stuart hirsts email of Jun 28: -> Thanks for your info but I think I have it working at last. Below are the steps I took which might help others. 1) Download the PCI AVM drivers from ftp://ftp.avm.de/cardware 2) Download the Chan_capi from http://www.junghanns.net/asterisk/ 3) tar -xvzf fcpci-suse8.0-03.09.10.tar.gz which

Hello, These are error messages I get when I try to call a number over CAPI channel. -- Executing SetCallerID("SIP/xlite1-3b80", "0") in new stack -- Executing Dial("SIP/xlite1-3b80", "CAPI/hfcpci/b17") in new stack > data = hfcpci/b17 > capi request for interface 'hfcpci' == hfcpci: Call CAPI/hfcpci/b17-1 (pres=0x00,

Hello, I just received a couple SX440isdn phones and was wondering if they can be plugged into a Diva 4BRI port in NT mode and work with asterisk+chan_capi? I know they probably work fine with mutliHFC cards with either bristuff of chan_misdn but since I have some spare Divas, I was curious about their potential as phone ports. The Diva's 3 and 4 ports are already set to NT mode at boot

Hi, i will use an AVM C2 controller with asterisk. How can i use both card ports ?? On the voip-info.org Wiki is only notice to: You will need a section for each controller in /etc/asterisk/capi.conf so the C2 will have 2 sections. But how is look like this ? Only on the first port is asterisk assume connections, but nothing on the second card port. In the dmesg is only the capidrv-1 shown,

hi, I've been running a pure sip asterisk box for a while now with no problems, and i've recently added an isdn2e line from bt in the uk. everything is hooked up and i've got it ringing my sip extensions, but the logs don't quite look perfect and i can't see any description of what i should consider to be normal behaviour. would someone be able to look this over and tell me

Hi all, does anyone have capiECT working? I can't get it to work - please see my logfiles below. While using an * CVS version of late September and chan_capi-0.2.5 (I guess), it worked!!! (I know, never change a running system ... should've backuped ... etc.) Here's the setup: NT----AgfeoISDNPBX----AgfeoISDNPBX----AnalogPhones in between the two PBX I attached my * server with a

Hi, I successfully installed 2 avm card in my asterisk box but I'm unable to make call. My capi.conf is: msn=0721111,07211115 incomingmsn=* controller=1,2 softdtmf=1 context=default echocancel=yes callgroup=1 devices=2,2 my capi info : Contr1: 2 B channels total, 2 B channels free. Contr2: 2 B channels total, 2 B channels free. my extensions.conf : exten =>

Hi, the first thing I did with Asterisk is listening to `demo-congrats' by Xlite on the same machine. This works perfectly. The config files are those shipped with the package. Now I want to listen to it over ISDN/Capi but I don't succeed. My `capi.conf' is like show in many tutorial on the web. In `extensions.conf' I just added the following lines: [capi-in] exten =>

Hi, I have done my best and tired of searching the net about the problem. If anybody could help would be a great favour. Description of Problem ------------------------ I am trying to install two Netpci cards(Traverse Technology Netjet ISDN-s) on Trixbox 2 and aim is to use in Asterisk as dailin and dialout. I compliled the driver as directed in the manufacture manual. After installation dmesg

Hi to all I've mada up my mind and i tried to change from i4l to chan_capi, following some councelling from the gurus. I compiled it up, and when i try to load it in modules.conf, i get that wonderful message and Asterisk does not start: [chan_capi.so]Feb 17 09:21:40 WARNING[16384]: loader.c:239 ast_load_resource: /usr/lib/asterisk/modules/chan_capi.so: undefined symbol: ast_get_group Feb

Hi, Regarding capi debug, I don't know how to translate reasons like 0x3302 or infos like 0. I didn't find any 'translator' googleing capi debugging. Do you know about any 'translator' for this or should I be as clever as to know what a reason 0x3302 is? What is this debug for if I can't interpret it? Kind regards, Victor. >From capi debug: == CAPI Call

I have a problem receving calls via the ISDN line, using the followin components Asterisk 1.0.9 with asterisk@home chan_capi-cm-0.6 AVM Fritz card datalink protocol = point to multimode I can make calls out with no problems so the issue is only incoming calls. When I make the call from an external line to the ISDN line connected to asterisk, I get a busy signal after about 5 seconds. I have

Hello All, I am having an odd problem with Armin's chan-capi_cm on builds higher than 7955. It would seem that this happens on anything higher than 7955. What is happening is the isdn is ringing, then asterisk does a goto-if and just hangs. Asterisk itself is ok, but the isdn then rings out or busys out on the other side. Outgoing works fine, this only seems to effect incoming. I

[Something seems to have went wrong with my previous posting. It appears on the archive page in another thread. I did not receive anything myself. So I may give it another try:] Hi, the first thing I did with Asterisk is listening to `demo-congrats' by Xlite on the same machine. This works perfectly. The config files are those shipped with the package. Now I want to listen to it over

Skipped content of type multipart/alternative-------------- next part -------------- A non-text attachment was scrubbed... Name: not available Type: image/bmp Size: 2918 bytes Desc: Picture (Metafile) Url : http://lists.digium.com/pipermail/asterisk-users/attachments/20050307/cb404791/attachment.bmp

Hello all, I'm trying to setup a AVM C2 card. I have read the kernel requirements for this card. <M> CAPI2.0 support [*] Verbose reason code reporting (Kernel size +=7K) [*] CAPI2.0 Middleware support (EXPERIMENTAL) <M> CAPI2.0 /dev/capi support [*] CAPI2.0 filesystem support <M> CAPI2.0 capidrv interface support My problem is when I make a "make