Hi, i will use an AVM C2 controller with asterisk. How can i use both card ports ?? On the voip-info.org Wiki is only notice to: You will need a section for each controller in /etc/asterisk/capi.conf so the C2 will have 2 sections. But how is look like this ? Only on the first port is asterisk assume connections, but nothing on the second card port. In the dmesg is only the capidrv-1 shown, no capidrv-2, only the isdnlog is shown the incoming call on the second port. Has anyone an usable (capi.conf?) configration ? Thx in advanced and regards, Andreas. -- appendix -- capidrv: Rev 1.1.2.2: loaded b1: revision 1.1.2.2 ACPI: PCI interrupt 0000:00:09.0[A] -> GSI 5 (level, low) -> IRQ 5 c4: PCI BIOS reports AVM-C2 at i/o 0xd000, irq 5, mem 0xe1000000 kcapi: Controller 1: c2-d000 attached kcapi: Controller 2: c2-d000 attached c4: AVM C2 at i/o 0xd000, irq 5, mem 0xe1000000 c4: revision 1.1.2.2 c2-d000: card 1 "C2" ready. c2-d000: card 1 Protocol: DSS1 c2-d000: card 1 Linetype: point to multipoint c2-d000: C2-card (3.11-04) now active kcapi: card 1 "c2-d000" ready. c2-d000: card 2 "C2" ready. c2-d000: card 2 Protocol: DSS1 c2-d000: card 2 Linetype: point to multipoint c2-d000: C2-card (3.11-04) now active kcapi: card 2 "c2-d000" ready. capidrv: controller 1 up capidrv-1: now up (2 B channels) capidrv-1: D2 trace enabled capidrv: controller 2 up capidrv-2: now up (2 B channels) capidrv-2: D2 trace enabled
Hi, i will use an AVM C2 controller with asterisk. How can i use both card ports ?? On the voip-info.org Wiki is only notice to: You will need a section for each controller in /etc/asterisk/capi.conf so the C2 will have 2 sections. But how is look like this ? Only on the first port is asterisk assume connections, but nothing on the second card port. In the dmesg is only the capidrv-1 shown, no capidrv-2, only the isdnlog is shown the incoming call on the second port. Has anyone an usable (capi.conf?) configration ? Thx in advanced and regards, Andreas. -- appendix -- capidrv: Rev 1.1.2.2: loaded b1: revision 1.1.2.2 ACPI: PCI interrupt 0000:00:09.0[A] -> GSI 5 (level, low) -> IRQ 5 c4: PCI BIOS reports AVM-C2 at i/o 0xd000, irq 5, mem 0xe1000000 kcapi: Controller 1: c2-d000 attached kcapi: Controller 2: c2-d000 attached c4: AVM C2 at i/o 0xd000, irq 5, mem 0xe1000000 c4: revision 1.1.2.2 c2-d000: card 1 "C2" ready. c2-d000: card 1 Protocol: DSS1 c2-d000: card 1 Linetype: point to multipoint c2-d000: C2-card (3.11-04) now active kcapi: card 1 "c2-d000" ready. c2-d000: card 2 "C2" ready. c2-d000: card 2 Protocol: DSS1 c2-d000: card 2 Linetype: point to multipoint c2-d000: C2-card (3.11-04) now active kcapi: card 2 "c2-d000" ready. capidrv: controller 1 up capidrv-1: now up (2 B channels) capidrv-1: D2 trace enabled capidrv: controller 2 up capidrv-2: now up (2 B channels) capidrv-2: D2 trace enabled
Hi, i think, the problem is: [chan_capi.so] => (Common ISDN API for Asterisk) == Parsing ''/etc/asterisk/capi.conf'': Found -- This box has 2 capi controller(s). -- CAPI[contr1] supports DTMF -- CAPI[contr1] supports supplementary services [...] -- CAPI[contr2] supports DTMF -- CAPI[contr2] supports supplementary services [...] == ast_capi_pvt(xxx,*,outside-isdn,0,2) (1,2,64) == ast_capi_pvt(xxx,*,outside-isdn,0,2) (1,2,64) == ast_capi_pvt(xxx,*,outside-isdn,0,2) (1,2,64) == ast_capi_pvt(xxx,*,outside-isdn,0,2) (1,2,64) -- listening on contr1 CIPmask = 0x1fff03ff Jan 4 23:10:03 WARNING[20274]: chan_capi.c:2836 load_module: Unused contr2 =========================================================================== But why ? In the capi.conf is explicit msn=xxx controller=1 .... msn=xxx controller=2 .... specified. -Andreas.
Hi, i think, the problem is: [chan_capi.so] => (Common ISDN API for Asterisk) == Parsing '/etc/asterisk/capi.conf': Found -- This box has 2 capi controller(s). -- CAPI[contr1] supports DTMF -- CAPI[contr1] supports supplementary services [...] -- CAPI[contr2] supports DTMF -- CAPI[contr2] supports supplementary services [...] == ast_capi_pvt(xxx,*,outside-isdn,0,2) (1,2,64) == ast_capi_pvt(xxx,*,outside-isdn,0,2) (1,2,64) == ast_capi_pvt(xxx,*,outside-isdn,0,2) (1,2,64) == ast_capi_pvt(xxx,*,outside-isdn,0,2) (1,2,64) -- listening on contr1 CIPmask = 0x1fff03ff Jan 4 23:10:03 WARNING[20274]: chan_capi.c:2836 load_module: Unused contr2 =========================================================================== But why ? In the capi.conf is explicit msn=xxx controller=1 .... msn=xxx controller=2 .... specified. -Andreas.