similar to: PRI & immediate=no

Hi ! I am trying to configure two E100P cards, but I am a bit confused with zapta.conf in what I am trying to achieve. The * will be connected to a pstn switch with two E1 PRI lines. The E1 lines will be used for incoming calls as well as outgoing calls. My problem now is what to put in zapta.conf, I would like to group all channels from both cards together (if that's possible). Does this

<P>hi Everyone,</P> <P>We are configuring an ISDN PRI E1 with an E100P card, when you load the drivers, and starts the asterisk, cards also starts fine, givin following output,</P> <P>*CLI> <BR>&nbsp; == D-Channel on span 1 up<BR>&nbsp;&nbsp;&nbsp; -- B-channel 1 successfully restarted on span 1<BR>&nbsp;&nbsp;&nbsp; --

Hi, I have an asterisk installation that has been happily working in production for some time (E100P and UK BT ISDN30). Recently I upgraded to HEAD-07/29/04. Now, incoming callers don't hear ringing while calling in. As far as I can tell, my config files haven't changed from what was working before. Can anyone please help before my boss shoots me? JC zaptel.conf

Hello, I have a little problem with signalling. An E100p is connected to an Alcatel PBX, wich has an E1 to the outside. Located in Germany. zapata.conf: switchtype=euroisdn pridialplan=local prilocaldialplan=local overlapdial=yes signalling=pri_cpe .... With asterisk 1.0.2 I can call from a SIP phone to a phone connected to the Alcatel and the SIP number is correctly displayed at the caller.

Hi, I'm installing E100P for isdn pri line. My configuration are like this. zaptel.conf ======================================= span=1,0,0,ccs,hdb3,crc4 loadzone = us defaultzone=us bchan=1-15 dchan=16 bchan=17-31 zapata.conf ================================================= [channels] context=default switchtype=euroisdn context=default signalling=pri_net usecallerid=yes

Hey all, I have an Asterisk-box with an E100P and a PRI (Euro-ISDN) coming into it from a Meridian-switch. The incoming numbers on this PRI all start with the same digit and the last part of the dialled number is signalled to Asterisk digit by digit, until Asterisk signals that the number is complete and the call rings. All works well, unless I have 2 or more numbers which start with the same

Advance apologies for the length of this mail; I have an ISDN PRI supplied by NTL (ex Diamond Cable, Nottingham) which is currently working happily with an SDX Index phone system. I have to replace this phone system shortly and I've been trying to get a * system working for some weeks now. I have configured the dial plan (which works) and all my SIP extensions (which all work) along with

Hi Guys I have a 4 port PRI card that I need to setup each port in their own group. In chan_dahdi.conf I have the following which works for one port How do I add the rest of the ports in their own groups so that I can have different signaling on each? [channels] language=en switchtype=euroisdn pridialplan=unknown resetinterval=600 echocancel=yes echotraining=yes

Folks, everything's in the subject, i've got a Linux Box with a Digium E100P E1 Card, modules are loaded, but I don't know which signalling to put in my zapata.conf... Thanks for you help. -- Nicolas Cartron nc@ncartron.org

Hi, We currently have an Asterisk box (P4 2.4 Ghz, 512Mb RAM, 1 T100P, Zhone Channel Bank and 1 E100P) connected to an ISDN running without any problems. That machine is working for about 1 year. Two days ago, we decided to switch that machine for two PowerEdge 600SC (HA) and we got some problems. The running machine (P4 2.4Ghz) has an Intel motherboard with four 32-bit 3.3v PCI slots,

Hello, I have the following configuration : E100P -> * -> TDM400 -> Modem When I receive FAXes, about 20% of them are corrupted : pages are not always complete. If the fax is complex or with numerous pages, it's usually a mess. Before that, I was using spandsp with success. Unfortunately it's too picky with some broken fax (training failed). Since this failure only occurs with

Hi, I have a problem with setting outgoing caller id to "nothing" (secret) on our Wildcard TE405P connected to a swedish euroisdn line. Caller ID seems to work fine when connecting the same line to a Ericsson PBX - so something must be wrong in my settings, but I don't know what. I've tried: exten => _*70X.,1,Set(CALLERID(name)="") exten =>

4 Port PRI sangoma a104 From: jg [mailto:webaccounts173 at jgoettgens.de] Sent: Wednesday, March 18, 2015 2:09 PM To: Andrew Colin; Asterisk Users Mailing List - Non-Commercial Discussion Subject: Re: [asterisk-users] 4 Port PRI I have a 4 port PRI card that I need to setup each port in their own group. In chan_dahdi.conf I have the following which works for one port How do I add the rest

Hi There, I have an asterisk an a Digium 4 Port E1 Card On E1 Port No. 1 I have the Telekom PRI On E1 Port No. 2 I have an Alcatel PBX that cannot be changed So I have setup my asterisk between Alcatel and Telekom In extension.conf i configured: [telekom] exten => _9149.,1,Dial,ZAP/g2/${EXTEN}; exten => _9149.,2,Hangup This works great, all incoming calls are directly routed to alcatel

Hi, all I am trying to install E100P card, the 'modprobe zaptel' is ok, but when I did 'modprobe wct1xxp', I got such error, so can not load the driver for the card. /lib/modules/2.4.20-8/misc/wct1xxp.o: init_module: No such device Hint: insmod errors can be caused by incorrect module parameters, including invalid IO or IRQ parameters. You may find more information in syslog

Outbound calls on my Telus PRI aren't taking the Name portion of the callerID. I've looked at the logs, and it is being set (see below), but the PRI debug output doesn't show the name being sent anywhere. As a result, received calls always display from Unknown (or just the number). Is there some config that I've missed somewhere? I'm running NI-1 (Telus says NI-2 doesn't

Good day all We got a Wildcard TE110P I installed linux,zaptel,libpti and asterisk I coped over my zaptel.conf and zapata.conf from a previous E100P config But when I try to start asterisk it gives error not bying able to load zap channles: == Parsing '/etc/asterisk/zapata.conf': Found Jan 10 08:17:18 WARNING[-1084595552]: chan_zap.c:9308 setup_zap: Ignoring switchtype Jan 10 08:17:18

Good Day all, I have a Fractional PRI connected to my Asterisk Box via a T100P card. When I initiate a call out to phone number 123-8888 the call sounds great no echo what so ever. If the person at 123-8888 hangs up and calls me right back (same handset on both sides) same trunk line The call always has echo on it. The Asterisk sip extension hears them selves echoing. The remote party

I am trying to setup Asterisk to act like a PBX connected via a PRI gateway to a voice netowrk where Asterisk is doing outbound overlap dialing for calls that terminate via that PRI. AFter researching through the archives and online dcocs, I thought I had everyting setup right, dialplan configured for '_X!' and the 'overlapdial=yes' in the chan_dahdi.conf file, but when I try and

Hi. I still hace problems getting my line to work. When I start asterisk, I can see: == Parsing '/etc/asterisk/zapata.conf': Found -- Registered channel 1, PRI Signalling signalling ... -- Registered channel 31, PRI Signalling signalling == Starting D-Channel on span 1 == Registered channel type 'Zap' (Zapata Telephony