similar to: PRI problems (telewest -> * -> LG GDK 186)

Skipped content of type multipart/alternative

Would be nice to do both (type 2 and 3 I believe in Oftel terms), but I'd accept just our DDI if that was all I could get. Steve -----Original Message----- From: Storer, Darren [mailto:starusers@comgate.tv] Sent: 01 July 2004 09:35 To: asterisk-users@lists.digium.com Subject: RE: [Asterisk-Users] Providing Telewest in the UK with per extension outbound callerID Hi Steve,

Hi all, I just configures my PRI and incoming calls are working fine but outside calling giving error PRI is BUSY :( any idea ? I have same setup on other box and that boxes works perfect. -- DAHDI/i1/6463279153-2 is proceeding passing it to SIP/7328-00000002 -- DAHDI/i1/6463279153-2 is making progress passing it to SIP/7328-00000002 -- DAHDI/i1/6463279153-2 is busy -- Hungup

Hi, I'm trying to install an E1 PRI, and I need it working by Monday, but although everything seems ok, I get no response to calls. When I make a pri extense debug on span 1, I repeatedly get the following: Sending Set Asynchronous Balanced Mode Extended [ 00 01 7f ] Unnumbered frame: SAPI: 00 C/R: 0 EA: 0 TEI: 999 EA: 1 M3: 3

Hey all, I am running a Asterisk 1.2.9.1 with Sangoma A101 card, newest firmware, configured with a help from Sangoma Tech Support, running fine. It is connected to a PRI circuit split from Cisco MC 3810, which in turn is connected to a Converged T from CTC Communications. While Asterisk works fine and I can call in/out on my BV account, I am only able to dial in through CTC. I have spent

Hello! Is it possible to connect Siemens HiPath 4000 to Asterisk? What equipment required on Siemens side? I mean IP not E1. Sorry for asking here. Siemens-related websites use "salesperson language". There is no technical information.

Hi, I have this setup: E1 PRI PSTN -- Asterisk -- Alcatel PBX - analog phones Can someone tell me what's wrong with this call initiating from an analog phone connected to Alcatel PBX? It dies with NOANSWER but all works if I call other destination numbers. Dialplan is a simple Dial(zap/g1/0984465691) statement. At the end you'll find also zapata.conf.

hello everyone, I have a trixbox server with an E1 card(not digium).It connects to an AVAYA pbx use E1. It works fine.But when i change the E1 card to digium TE220B,there is a problem. When sip extension A(on trixbox) call PSTN extension B(on avaya),A must wait longtime before B start to ring.From the log I find there are two times call. I don't know why the first request be rejected

Hello all, the scenario: Carrier ----S2M------ * -----S2M------Siemens | | SIP Clients and many other features With much help from the list, the PRI links are without alarms and inbound calls are working fine (from both: Carrier and Siemens). But I am not able to dial wether outbound nor to the Siemens PBX. I allways get the message: == Everyone is busy

Hi, When we make an outgoing call on ISDN (zaphfc) with overlap dialing we get immidiate hangup after answer. But when we place a full number before dialing everything is ok. Any help appriciated!! Thanks here is info with debug: == Primary D-Channel on span 1 up -- Executing Dial("SIP/200-164c", "zap/g1/|100|tc") in new stack -- Making new call for cr 192 --

I just downloaded the cvs version CVS-07/28/03-14:45:19 and now I cannot recieve the the calls from the zaptel interface which is a E100P with pri signaling. That is something with asterisk becouse rolling back to version from 06/23/03 using the new libpri and zaptel fixes the problem. Here is an exept from the config: [macro-stdexten]; ; ; Standard extension macro: ; ${ARG1} - Extension

Hi all, I have an asterisk-server (cvs-head from august) connected to a carrier's switch (DMS/Euroisdn) via a te410p, and I am having problems with DDI (standard 'official pstn' number plus extra digits for 'internal' use) Basically, when the entire number (including the extra digits) is dialled via a redial or a programmed key, I see the entire called party number (including

Is there a setting somewhere in * to define whether I am receiving callerID or true ANI? Global Crossing claims they are sending ANI but I dont think so. My understanding of ANI is that it is always sent, regardless if callerID is blocked. If I dial *67 and my DID, I get "Presentation: Presentation prohibited of network provided number" and no number. Before I call GC on Monday

I'm having some trouble here - need some help! I've just bought a TE405p (32-bit 5V), but cannot get it working in a dell 6450. The dell has (from tech specs) "three peer PCI buses: two 64-bit buses and one 32-bit bus Expansion slots seven hot-pluggable PCI slots (two 64-bit/66 MHz, four 64-bit/33 MHz, and one 32-bit/33 MHz)" I cannot get the card working in any of the slots.

I have a PRI link up and running between Asterisk and a Nortel Norstar MICS v4.1 . I'm having a problem getting the textual Caller Name across the link from Ast to Ns, however numeric Caller ID arrives and displays fine. From Ns to Ast both elements come through fine. I'm forcing dummy values for testing using: exten => s,1,SetCIDName(Test) exten => s,2,SetCallerID(1234561234)

OK I am going to do it again. Global Crossing is now sending ANI but it is not in the format I expected. Any one know of a way to get this data into two seperate variables? The first number is ANI and the second is DNIS so it is "*tendigits*tendigits* on one line like below. < Called Number (len=26) [ Ext: 1 TON: National Number (2) NPI: ISDN/Telephony Numbering Plan

Hi all, using latest asterisk-svn I want to reflect an video call incoming via an PRI EuroISDN channel to another outgoing PRI channel, and I want the the outgoing channel to have the exact same bearer capability < Bearer Capability (len= 5) [ Ext: 1 Q.931 Std: 0 Info transfer capability: Unrestricted digital information (8) < Ext: 1 Trans mode/rate:

Hi. recently I have been trying to setup a PRI on asterisk. Inbound calls are working just fine but I am not able to make outbound calls. Does anyone know what I need to change to make outbound calls work? Right now the PRI is instantly hanging up on the outbound calls. I have included full debug info as well as config files. /etc/zaptel.conf span=1,1,1,esf,b8zs bchan=1-23 dchan=24

Hi there I've got a rather irritating problem with my Asterisk server. Whenever someone tries to call me, the don't get the usual "ring-tone" when they wait for me to pickup the phone. I don't know if I've disabled this feature somewhere in my configuration files. Since I'm in Denmark, I've got an entry in the indications.conf file pointing to

I have attached my PRI debug out put when making an international call - hopefully it can shed some light on the situation. I am sorry if this attachment gets to the list twice, I sent one early this morning, but it has yet to appear - i may have sent that one in error. Kind Regards: Gabriel -------------- next part -------------- An HTML attachment was scrubbed... URL: