similar to: ADIT 600 Manual

Has anyone had any success using the Adit 600 with the CMG card talking MGCP to asterisk? I want to have a central asterisk server with 10 Adit 600's at various locations providing 24 FXS ports.... Thanks, Isaac

Got at suggestion from CarrierAccess to use the Adit 600 as an VoIP router using MGCP IP protocol, instead of controlling it through an E1. Have anyone tried this configuration? How does MGCP works? I've tried to search for it on Google, but I only find the protocol specification for it. Is Asterisk fully capable of this? I can't find any documentatin covering the use of MGCP in Asterisk.

Say I get an ADIT 600 with two FXS8A and one FXO8A from ebay. a. Is it good for Asterisk? b. How do I connect the extensions and lines to it? Do I need a special jack? Can I get that jack in every corner? c. where can I find help for configuring it? d. what kind of backup does it have? Does it need to be reconfigured after a power outage? Shoval Tomer, IT Manager, SofTov Advanced Systems, Ltd.

Can anyone help me with the term that SBC uses to refer to disconnect supervision? I have an Adit 600 channel bank which has helped improve the disconnect detection time down to about 8 seconds. This is still causing some issues in particular with call progress enabled in * we are having a few disconnects while calls are in session (about 2 reported in first 5 days of use). I have talked both to

According to CarrierAccess, the Adit 600 uses CAS for voice signalling. What is this? This should not be a problem for Asterisk? Does the Asterisk server need to reencode CAS into aLaw when going to Euro ISDN? BR Daniel Nystr?m

Hello, I'm about to install asterisk as the PBX at a location that my company has just moved into and I would like to get some comments and advice on the installation. I am new to * and don't want to make any big mistakes so I would love to hear whatever anyone has to say. Here is what I have so far Server: * 2.8Ghz P4 - 1G ram * T400P Tormenta II (is this as good as the

I've been reading the Google searches trying to understand how to tie together Adit 600 to Asterisk to provide 2 way service. I'm about blind from reading. I assume, the answer is using MGCP between the boxes. However, the examples I found don't really explain fully enough to know how to modify examples to work for me. I'll have in the ADIT with T1's. There is a CMG and

I have an adit 600 with an fxo card connected to a digium T1 card. If I try to make an outgoing call and the T1 cable is disconnected, asterisks returns congested like it should. But, if the adit 600 is connected to the T1 card, the adit 600 immediately "answers" the call even if there are no physical lines attached. I even removed the fxo card and the adit 600 still

Ok, I've pretty much decided to try the Adit route. Somebody who has experience with these tell me if I'm missing something. I have 15 incoming PSTN lines. T1 is not an option at current location. I want to put in an Adit 600 with 2 8-port FXO boards. The adit will then connect to * via a digium t1 board. I configure zaptel.conf for the T1. What other parts would be needed? How do

Folks, I'm experimenting with bringing multiple (8) analog lines from our local telco into a Carrier Access ADIT 600 channel bank with an FXO module, then having this talk to Asterisk via the T1 TDM controller on the ADIT and a TE405P card. I don't know if this will work well (ie: give me decent echo cancellation, call disconnect supervision, caller ID etc) but I haven't had much

Hello, I am connecting Asterisk to an Adit 600 via a T100P. Unfortunately I am not able to get any lights on the T100P and the Adit 600 only shows red. I have already modprobed the t100p. Has anyone successfully connected these before? I've tried both a cross-over cable and a standard cat 5 cable, but I can't seem to get them to work. Any suggestions? Thanks! Craig

Hi, I'm using an Adit 600 Channel Bank with *. I love it and it works really great for my FXS lines. One problem that I have with it (It's really not a problem yet, but it's a potential one) is that I've scoured the manaual for the Adit to see if there's a way to dump out a config file from the bank so in the event of a power and battery failure I don't have to type in the

I've finally got my Adit 600 and are configuring it right now. But I have to say, there aren't much documentation for it. I've setup MGCP and Asterisk seems to find it. But all channels (40 FXS channels) are "Down"! But the MGCP itself is "Up" according to the statistics. I can't find any documents how to set each channel to "Up" in the CLI. Any

Can anyone help me with the term that SBC uses to refer to disconnect supervision? I have an Adit 600 channel bank which has helped improve the disconnect detection time down to about 8 seconds. This is still causing some issues in particular with call progress on we are having a few disconnects while calls are in session. I have talked both to some local phone contractors and SBC directly and

Hello All, I'm trying to connect Asterisk to an Executone phone system with an analog DID card and I'm hoping someone can help me figure out what I'm doing wrong. The Executone DID card provides battery to the telco, when the telco wishes to dial a DID it goes off-hook, waits for a wink from the Executone and then dials the last three digits on the number with pulse (as opposed

I've searched but can't find an answer as to how many MGCP paths can a single ADIT/CMG card support? It appears it's only 24 ports, maybe 48. What I'd like to do is install 6 Telco T1's into a single (or more) Adit 600 and route inbound calls towards asterisk. Can I have more than one CMG in a single chassis? Or maybe you know of a better way to connect T1's to

Hello, I have an Adit 600 (3 FXS cards) hooked up to a digium T1 card in my asterisk box. I 'connected' the slots to the a:1 T1 interfaces via the command line. The slots (3 fxs) are configured with 'ls' signaling. I configured the T1 card with the same line settings as the T1 interfaces on the adit and I get green lights on both the T1 card and the T1 interface on the adit (so

After months of setting up Asterisk. I completed the final testing last night We would go live on Monday. Or so I thought. As I moved the Adit 600 back out of the way, sliding it six inches. I noticed the major light was red as were both T1 and T2 lights ( eventhough only one t1 port is being used ) -- I have no idea what these lights mean or if they were lit before when things were working.

I'm emailing this as the customer in this case, since my carrier appears to be completely unable to solve this. A brief rundown of the problem: - We have several voice lines going through the ADIT, of course into a VoIP type of arrangement. - Voice traffic will become choppy, even drop calls completely, at random but quite often. Modem calls (which we needed unfortunately) are a joke. -

I'm having issues with echo. My setup is Polycom IP501 phones connected to an Adit 600 via T100P. 13 Lines going to the Adit. All echo so far is on the local side (Employees hears own voice, but only on some calls). Watching the channel with ztmonitor, I notice that TXGAIN is pegged out most of the time. RXGAIN is anywhere between 45 and 60%. Is it safe to assume that playing around