similar to: Carrier Access CMG/FXS MGCP to Asterisk, Works Fine

I had MCGP working to a ADIT 600 fine with debain sarge stable / asterisk stable - wanted to try red hat and got the below message - then I re-installed debian and am still getting the same message below - any comments are greatly appreciated - I did play with the config files with no prevail - the Adit seems to be doing its job per tech support at CAC. I listed my conigs below I go off hook

I've searched but can't find an answer as to how many MGCP paths can a single ADIT/CMG card support? It appears it's only 24 ports, maybe 48. What I'd like to do is install 6 Telco T1's into a single (or more) Adit 600 and route inbound calls towards asterisk. Can I have more than one CMG in a single chassis? Or maybe you know of a better way to connect T1's to

I've been reading the Google searches trying to understand how to tie together Adit 600 to Asterisk to provide 2 way service. I'm about blind from reading. I assume, the answer is using MGCP between the boxes. However, the examples I found don't really explain fully enough to know how to modify examples to work for me. I'll have in the ADIT with T1's. There is a CMG and

Has anyone had any success using the Adit 600 with the CMG card talking MGCP to asterisk? I want to have a central asterisk server with 10 Adit 600's at various locations providing 24 FXS ports.... Thanks, Isaac

Got at suggestion from CarrierAccess to use the Adit 600 as an VoIP router using MGCP IP protocol, instead of controlling it through an E1. Have anyone tried this configuration? How does MGCP works? I've tried to search for it on Google, but I only find the protocol specification for it. Is Asterisk fully capable of this? I can't find any documentatin covering the use of MGCP in Asterisk.

ONLY ON MONDAY! Well it used to work - calls between my aaln's that is. I moved from debain to redhat (same conf. files for asterisk) and this is what I get.. looks like several errors. errors I never got before. Also asterisk isn't observing the digits as I dial them like it used to however it still trys to route the call when I'm finished dialing. Anyone with a though on this?

I've finally got my Adit 600 and are configuring it right now. But I have to say, there aren't much documentation for it. I've setup MGCP and Asterisk seems to find it. But all channels (40 FXS channels) are "Down"! But the MGCP itself is "Up" according to the statistics. I can't find any documents how to set each channel to "Up" in the CLI. Any

Dear all, I have some C code using the zlib uncompress. It compiles fine under Win XP (with SP2) with R up to 2.3.1 and generates four files (Makedeps, *.d, *.dll, and *.o): C:\Data\R-packages\cmg>rcmd SHLIB cmg.c -o cmg.dll latex: not found making cmg.d from cmg.c gcc -IC:/PROGRA~1/R/R-2.3.1/include -Wall -O2 -c cmg.c -o cmg.o cmg.c: In function `readcmg': cmg.c:33: warning:

I have this idea to use an old ADIT 600 with a CMG card to convert two T1 TDM circuits to MGCP towards asterisk. The basics I've found on the net, but there is not much available. I've cut and pasted the mgcp.conf details I could find, but there not much as far as CMG setup. I was hoping I could hook-up with someone that's tried this so I could pick your brain about the finer

Hello, I am working for a charity in the UK and I am projecting a new phone system. We would like to connect our two-wire telephones (40 or so) to an ADIT 600 channel bank, and connect that into an Asterisk box via the CMG card or T1 card. I have been in talks with Carrier Access about the purchase of a new channel bank and we tried to get a minor version of it first for testing with the

Hi there, I'm trying to get hold of an evaluation IP-enabled FXS channel bank. I'm not sure if it's more a channel bank, or should be called a multiport-ATA. Oh well. On the surface it looks quite nice - 16 FXS ports, and since it's connected to the network I can do away with an E1/T1 connection required of the normal channel banks (if it can be called that :) Here are some

Hi, Anybody out there running Adit600s? I have in my care an Adit600 channel bank connected to an old (version 1.0.6) Asterisk instance with MGCP. When trying a more recent Asterisk (1.4.21.2~dfsg-3+lenny1, Stock current Debian) calls fail. I have attempted to add the "slowsequence = yes" line to mgcp.conf. (It seemed to be the only likely candidate in the example files I found

I'm looking for an inexpensive way to connect 20 analog phones to asterisk. I could get a bunch of Linksys or Sipura boxes but was wondering if there is a more cost effective way? I came across the Mediatrix 1104 and even the Mediatrix 1124 but that comes out to be almost $100/port. I might as well buy inexpensive IP phone. Does anyone have any suggestions? Thanks, Waldo

All: Any have sample config's for an ADIT600 w/ CMG card connected to an Asterisk box via MGCP? Thanks, Garrett Smith <mailto:gsmith@voipsupply.com> gsmith@voipsupply.com VoIPSupply.com -- a division of B2 Technologies, LLC (716) 250-3408 Direct (716) 630-1548 Fax (716) 903-9495 Cell AOL IM: B2sales VoIPSupply.com is North America's largest VAR

I am forklifting a Merridian option 51c with 112 Nortel Digital Handsets and 400 analog units. For the analog units I have quotes for 9 ADIT 600 48 port fxs units and 17 Rhino 24 port FXS channel banks. I have used neither. Which is the best choice? The price difference is not that great. I am looking at Citelinks 24 port Handset Gateway for the Nortel Digital units. (Any other suggestions

I've got a ShoreTel 210 MGCP phone drops calls. My packet capture indicates that the phone may be trying to renew its registration with *, but reports Restart Method of Disconnected (frame 2), then * seems to take that as a sign that it has lost the connection and closes things down. The phone, meanwhile, seems to think it can continue the conversation until a few ICMP "port

see below I tried to call 98013356 from the following phone (from mgcp.conf) [iptlf03] host = 192.168.33.3 context = default inbanddtmf = 1 callerid = 22545062 line => aaln/1 Console output: == Spawn extension (capiring, 9988001133335566, 1) exited non-zero on 'MGCP/aaln/1@iptlf03-1' -- MGCP mgcp_hangup(MGCP/aaln/1@iptlf03-1) on aaln/1@iptlf03 -- Delete connection 4

I've been trying to figure this one out for a while, but to no avail. I have my cisco ubr924 setup for MGCP with Asterisk as the call-agent. I have manually registered the endpoint in mgcp.conf. When I pick up the phone, I get no dialtone and debug shows errors. IOS on the ubr924 is 12.2. Any help is appreciated. from mgcp.conf: [ubr924] host=65.37.86.203 context = from-sip (just as a

Hello, I`m try to make the attended transfer work Dlink DG-104S via FLASH, when somebody calls my phone I pickup and press flash to get a second line to call another extension. When I press flash I hear no dialtone, and only a long and then small beep. When I try to dial digits I hear again those long+short beeps, but the extension dialed is not ringing. If I pres flash again I get back to

I know this is not the most appropriated list to this, but I will try: Does anyone know what is the criteria to the generation of the transaction identifiers in MGCP? I mean, are they generated by a randomic method? I'm using Asterisk and MGCP eyeP Phone and observed that the RSIP and NTFY (methods created by the gateway) use high values in the transaction identifiers, while the RQNT, AUEP,