similar to: zttool and errors

Hi List, After reading a bunch of the docs, list post archives, it still seems that a clear definition of how to clock the T100P card is muddy. zttool says that the link is "INTERNALLY CLOCKED", does this mean the T100P is providing clock, or does this mean the T100P is getting clock from the T1 line side (ergo getting clock from the Telco) ?? If you have sync = 0 then zttool

Hi, I'm trying to connect a PC with a TE410P to an E1/IP equipment. Unfortunately I keep getting a yellow alarm from zaptel (in zttool) and a Loss of Framing alarm on the remote equipment. The E1/IP is connected on the other side to a PRI interface on a GSM MSC. I have configured the span as: span=1,1,0,ccs,hdb3 (also tried span=1,0,0,ccs,hdb3) and the channels as: bchan=1-15,17-31

Hi list, We have been trying to configure a Quad Span T1 card in a system running RH9. We have followed the instructions in the Wiki and searched the mailing lists, but so far havent got any success. Cable is connected to the first span, and module is loaded. Without loading the module the LED glows in red colour, but the moment we load module, it goes off. (No red or green) . We ran zttool

Hello guys! I hope you bare with yet another newbie on the list! :-) I am trying to setup an asterisk installation in between a Siemens HiPath 3800 and my local carrier (Telefonica/Brazil). Both running R2. ISDN is not an option on the carrier. :-( I could apparently setup both E1s just fine according to zttool (both OK with no alarms) but, and this is where it starts to get

Hi to all, I have a problem with this wildcard and one E1 line. The server is a Asus P4P800S with the 865PE chipset, and 512MB RAM. The kernel version is 2.4.26. I have donwload and build the latest CVS version of zaptel, libpri and asterisk following the ufficial instructions of digium. I have set up my server in this way: zaptel.conf loadzone=it defaultzone=it

New to list, going through steep learning curve with *, could someone assist with how to install zttool with slackware10, the normal make zttool fails, assume I am missing a dependency? (newt and newt-devel?) Trying to test Q.031 pri span with TE405p card, Google has little clue on Zttool and the * manual has a heading, but no entry? Thanks Magnus

I've been running Asterisk for months with no problems. I have grown to the point where I need an aditional TE cards. After many attempts I was able to add the second card without affecting the performance of the first. However, the second card is not working properly. Setup ===== - Running on a Dell Server. - RedHat 8 - Asterisk 1.0 - I have two TE410Ps on that box, card 0 assigned to

I have a TE405/TE410P card that was working on 1.0.X I upgraded the OS to Centos 4.5, Updated asterisk to 1.4 and zaptel to 1.4.5 and libpri. I copied all the zaptel and zapata and extensions.conf files from 1.0 I did update extensions.conf from 1.0 to 1.4 commands. I cannot get the card to work in 1.4.10. AHHH! I see with zttool that the T1 is in Green, I see calls coming in as the bits go

Hi, I installed s fresh system yesterday and it seems that zttool did not install!! ztcfg is there.. Anyone else had this problem or is it just me? -- ______________________________________________ http://www.linuxmail.org/ Now with e-mail forwarding for only US$5.95/yr Powered by Outblaze

Good day everyone, A Solution now exists for those of you still looking for the first model of Quad T1/E1 Interface Cards - the T400P and E400P. The T400P and E400P were manufactured by Digium until a few months ago, and were designed and released under the GNU Public License as the Tormenta II by Zapata Telephony. Varion, Inc. is now in full production manufacturing these boards. With the

Hi, It seems like my ATA is making a ringing noise... (as it used to), but now (After the upgrade from 1.0.7 to 1.2) asterisk also is either making the ringing, or passing the PRI ringing from the telco on to me. Any suggestions on how to fix this?

I just installed a TE410P on a Debian Sarge system running kernel 2.6.11-1-686-smp. Zaptel and Asterisk seem to be working fine. However, I have a couple of problems with the TE410P and Zaptel. First, the TE410P is showing me red alarms on 2 of the 4 T1s. This board (the TE410P) was just moved from another machine running REL3 and all 4 T1s were working there. I don't know why only

Hi all, I have a box running asterisk with T410 connected to a Nortel DMS 100 switch and another box running SER with grandstream phones on it So if there is a call from the pstn it goes from the Nortel to the asterisk and then to the SER box and finally to the phones.if the phone is busy or the number is invalid the * box will first send an ALERT message to the Nortel and say the call is going on

Hello everyone, I'm using a TE410P, no irq sharing, and all extraneous devices disabled, such as USB, Parallel etc. I'm getting a few IRQ misses according to ZTTOOL. We're running a standard PRI_CPE interface and seem to be getting dropped calls, and errors on the D-CHANNEL occasionally. The circuit itself is very solid, it was in use on our old PBX just a few weeks ago, never

Just noticed that no matter what the line condition is, zttool always reports "OK", so it's pretty useless. (In contrast, I'd get "Red alert" if I unplug the line connecting to an X100P.) I'm using zaptel 1.2.15 on Linux 2.6.15-28 (also tested on 2.6.10). Yuan Liu

SYNOPSIS Erratic red alarm T1 PRI on asterisk, but zttool running concurrently during alarm shows no errors, irq misses, or alarms, on any span. Using asterisk and quad Digium T405P, configured as follows: Span 1 connects to ISDN PRI (fractional 8 B channels, D channel 24). Span 2 connects to T1 Mux and analog stations. Span 3 connects to ISDN PRI Nortel BCM hybrid key system digital trunk.

Hello, I am missing any description of zaptel/DAHDI alarms. The TE200 series user manual contains only a description of LEDs states. These alarms states are visible in zttool/dahditool or in astersick CLI (zap show status) and I wonder what is the real meaning of these alarms for E1 channel. Possible alarm states (based on zaptel.h 1.2): 1. No alarms 2. Recovering from alarm 3. In loopback

In my * server I have a T100P, connected with a T1 crossover cable to an Adtran TA750 with 2 FXO cards. After I do 'modprobe wct1xxp;ztcfg' the alarm on the card starts blinking red. Running zttool confirmed that yes, it is a red alarm. I've read a few previous posts on this type of setup and I'm not too much closer. What should I be checking next? A different cable? The

An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20040810/16371a21/attachment.htm -------------- next part -------------- ? Hi, I'm using TE410P card with four T1 lines. I've configured all the channels in my /etc/zaptel.conf file. In zttool i'm getting "OK" for the "Span-1" but the other three spans giving

Hey all, I had a user complaining of calls which were dropping mid-conversation. I looked into the time of one of the calls, and saw the following: Apr 4 12:13:03 WARNING[6670] chan_zap.c: No D-channels available! Using Primary channel 28 as D-channel anyway! Apr 4 12:13:05 WARNING[6660] channel.c: Avoided initial deadlock for '0x82b8430', 10 retries! Apr 4 12:13:05 WARNING[6660]