similar to: ISDN-PRI - WCT1XXP error

Hi All, I wish to connect * to a Cisco using a E100P board. When I load the driver I got this error message: -bash-2.05b# modprobe wct1xxp ZT_CHANCONFIG failed on channel 1: Function not implemented (38) /lib/modules/2.4.21-SAX/misc/wct1xxp.o: post-install wct1xxp failed /lib/modules/2.4.21-SAX/misc/wct1xxp.o: insmod wct1xxp failed Follows Cisco configuration: isdn switch-type primary-qsig

Hi, I have two E100P boards connected to my PC. I wish to setup two E1-ISDN-PRI lines, the first SPAN with 15 channels and the second one with 30 channels. When I try to load zaptel modules, I get an error message: "Loading zaptel framework: Loading zaptel hardware modules: wct1xxp wcusb Running ztcfg: ZT_CHANCONFIG failed on channel 63: No such device" Follows my zaptel.conf:

Are there any sip providers out there providing full business telephone service. Not just single line/residential service like I have seen with vonage etc. For example take a company currently using a legacy pbx connected to the PSTN with a PRI. I would like to replace this setup with a data T1, an asterisk box, and some SIP Phones then pass all calls (local and long distance) directly

Hi guys, Thanks for your answers on my two questions yesterday. That's exactly what I was looking for, sorry for not noticing it myself, but I'm still getting acclimated to Asterisk and even Linux--from what I see so far, I love it. I've got another one now. Since my Asterisk install and configuration is fairly stable at this point, I'm interested it ensuring that during

All, I am trying to configure hdlc support on T100P Digium card - everything seems ok... but it just does not work at all. I was able to compile all drivers, the light on the card becomes green when I plug T1 link.... but I even can't ping default router IP... there is no data coming back to me, so I am confused completely now. Also I tried both protocols - raw hdlc and cisco hdlc. The

I'm trying to use ztcfg with the following zaptel.conf: span=1,1,0,esf,b8zs bchan=1-4 nethdlc 5-23 dchan=24 and I get "ZT_CHANCONFIG failed on channel 5: Function not implemented (38). This is on Debian 2.4.26. I have hdlc compiled as a module. Should hdlc be compiled into the kernel? Does anyone see a problem here? Thanks, -- Michael Welter Introspect Telephony Corp. Denver,

Just cross pairs 1-2 and 4-5 1 <--> 4 2 <--> 5 Never done an E1, but I think it's the same for a T1 4 wire cable. Tim Thompson Commercial Sales Engineer http://www.amatechtel.com (806) 722-2227 -----Original Message----- From: bam [mailto:bam@cqm.co.uk] Sent: Monday, December 29, 2003 9:12 AM To: asterisk-users@lists.digium.com Subject: [Asterisk-Users] E100P pinouts

my target is to produce a linux router with T100p to Fract T1 24chan to ethernet and TDM 4channel FXO. I have not been able to get nethdlc to work, just get zaptel networking not configured if I set bchan and dchan the card comes to life, but I don't believe this is correct for what I want to accomplish. according to markster@ this is the way they do it. using (multiple distro versions

Hi my question is: which is the best distribution to work with asterisk? thanks mark

Hello ml, i need some help on my zaptel configuration. My E100P only shows some YELLOW / RED alarm when I load the wct1xxp module and do a cat /proc/zaptel/1 Span 1: WCT1/0 "Digium Wildcard E100P E1/PRA Card 0" HDB3/CCS YELLOW RED ... .. . My /etc/zaptel.conf is: span=1,1,0,ccs,hdb3 bchan=1-15,17-31 dchan=16 loadzone=nl defaultzone=nl I tried zaptel-1.0RC2 and the latest CVS

Hi folks: Does the TDM400 card from Digium only support FXS, or is FXO functionality available or planned? -- Ron Gage - Saginaw, Michigan I am looking for work - resume at http://www.rongage.org/resume.doc Electrical Engineering, Linux Programming, Networking

Anyone tested this card in Greece? I would like to buy several of these but I don't know if it works well with the PSTN in Greece. The Quicknet Linejack card seems to be unable to understand the telephone network's tones (busy, ringing,...). TIA, Michael.

Hello all, A newer version asterisk-oh323 (v0.5.5) is available. This version contains updates for compilation with latest Asterisk sources, some additions ("atexit" cleanup) and some other fixes. http://www.inaccessnetworks.com/projects/asterisk-oh323 Regards, Michael.

Hi all, i don't know how often someone ask for this, but i ask agian: Is it possible to use G723.1 with * or not ? I tried to use G723.1 from * over OH323 to a gatekeeper from my provider. The situation is following: Zap/analog ---> IAX -----INTERNET-----IAX--->OH323---->GATEKEEPER/PROVIDER The provider supports G723.1. Can someone help me ? Regards, Thomas.

(to mods: sorry for any extra work I've put you through. Posting from my work account, as proper) Hello all, I'm back. I've got that lucky feeling that this will all work out very soon, and I hope that that is true. The issue: In my * server I have a t100P, connected with a T1 crossover cable to an Adtran TA750 with 2 FXO cards. After I do 'modprobe wct1xxp;ztcfg' the alarm

If you have an FXS port and would like to attach a PSTN analog line to it this device would do the job by converting the FXS port to FXO. It's a small external device. Works well with VOIP FXS and other FXS interfaces. Interface: 2 RJ11 Jacks (one for the FXS port and one for the PSTN outlet.) Cost: $35.00 with USPS regular mail included. Power: 9 to 20V dc power supply (Not

Hi, I'm cutting my teeth setting up a home asterisk server, but having some trouble getting Zaptel to recognize a X100P clone PCI (Motorola SM56 which should work according to various wiki's). What struck me was that the "/proc/interrupts" do not include IRQ 11 as the "lpcpi -v" is reporting. Am I missing something fundamental here? Any hint is greatly

Mythical Asterisk Creatures, oft-discussed, rarely seen: 1) An "advanced" graphical user interface 2) An IAX2 hardware device 3) A Radius CDR report module 4) A live-method, robust SQL-based dialplan 5) LDAP/SQL/Radius authentication for SIP phones 6) Robust R2 signalling support 7) Multilingual language recordings of all existing * .gsm files 8) Free exchange of PSTN gateways in

Hi, all I am trying to install E100P card, the 'modprobe zaptel' is ok, but when I did 'modprobe wct1xxp', I got such error, so can not load the driver for the card. /lib/modules/2.4.20-8/misc/wct1xxp.o: init_module: No such device Hint: insmod errors can be caused by incorrect module parameters, including invalid IO or IRQ parameters. You may find more information in syslog

I am running RedHat Fedora Core 3 with their "kernel-2.6.10-1.741_FC3" kernel, and if I use nethdlc in zaptel.conf, when I run ztcfg I get the message: ZT_CHANCONFIG failed on channel 11: Function not implemented (38) Does anyone have ideas on how I can work around this issue? T1 channels 1-10 are voice, 11-24 are data (second board isn't used at the moment). Here is my