similar to: X100P Driver loaded, but no IO on /dev/zap/1

Hi All, Googling X100P Clone I found several information about these cards and seems that some winmodem has the same chip used from the original X100P. Here below a list winmodem which should work as X100P clone: 1057 Motorola 5608 SM56 PCI Fax Voice Modem E159 Tiger Jet Network Inc 0001 Tiger 300/320 PCI interface I bought one "Trust 56k V92 PCI Internal Modem MD-1100" which has the

Hello After having installed my X100P, /proc/pci and /proc/interrupts dosent locate them. In my PCI list is it the Communication controller: Tiger Jet Network Inc ? then is dosent have a IRQ listed in /proc/pci.. All help appreciated Thanks and Regards Ajit ===========================/proc/pci================================== PCI devices found: Bus 0, device 0, function 0: Host

So I took a chance with an X100P knock-off on eBay. I'm running Asterisk + FreePBX on a PowerMac G3 (beige desktop) using Slackintosh 10.2 and kernel 2.6.16.16. Everything has been fine up until now. I compile the 1.2.5 Zaptel drivers without a problem, get the udev configuration in, modprobe zaptel, and finally modprobe wcfxo. At this point, I get the message: ZT_CHANCONFIG failed on channel

Thank you for the suggestions Andrew. I have not come across some of them before and will give them a shot. Based on my reading, changing the motherboard should have minimal impact unless that motherboard and the TDM400P don't get along (aka. IRQ sharing). I have disabled everything that is not needed and I do not believe I have any IRQ problems and I am NEVER wrong ;). Calls are crisp and

I was studying the asterisk-users list archives to learn if anyone has had success with an X100P on a sparc. I noticed some postings on the subject. I am wondering if anyone has learned anything new? I have an Ultra-60 running Gentoo with 2.6.10 and udev. I built * 1.0.5 and have been enjoying various SIP configurations, with 2 sipura phones and 2 UIP200 phones (got them working!) in my home,

Hi all, I have installed a TE110P in a BOX but when I load zaptel module I can't see any device in /proc/zaptel. And led of the card is green. My zaptel.conf is the next: span=1,1,0,ccs,hdb3,crc4 bchan=1-15,17-31 dchan=16 loadzone=es defaultzone=es and cat /proc/pci throguh next: PCI devices found: Bus 0, device 0, function 0: Host bridge: Intel Corp. 82845 845

I have just got my X100p card and am trying to install it. I have built and installed the zaptel drivers without any apparent errors and I am now trying to get them working. I have the following in config files In /etc/zaptel.conf fxsks=1 In /etc/asterisk/zapata.conf signalling=fxs_ks context=default channel => 1 Now when I try ti modprobe the drivers this is what happens: Command:

Hi all, I have just purchased the DevKit from Digium and received a X100P and a TDM400P (it has one FXS module). The problem is that I can't get the kernel module (wcfxs) to load and run. I have searched the archives and can't find anything about this. Do the messages below ring any bells with anyone ? There is no interrupt clash (see pci list below). I am running on a AMD 1.2G

Thanks in advance root@asterisk01:~# modprobe wcfxo /lib/modules/2.4.20/misc/wcfxo.o: init_module: No such device /lib/modules/2.4.20/misc/wcfxo.o: Hint: insmod errors can be caused by incorrect module parameters, including invalid IO or IRQ parameters. You may find more information in syslog or the output from dmesg /lib/modules/2.4.20/misc/wcfxo.o: insmod /lib/modules/2.4.20/misc/wcfxo.o

Hi, I'm using zaptel-1.2.22.1 with asterisk-1.2.10 and following steps to make zaptel working... OS is gentoo linux 2006.1 Hardware: --------- 0000:05:01.0 Communication controller: Tiger Jet Network Inc. Tiger3XX Modem/ISDN interface Subsystem: Unknown device 8085:0003 Flags: bus master, medium devsel, latency 32, IRQ 22 I/O ports at b400 Memory at ff900000

Hello All... I have searched in the archive and also followed Zara's instruction on getting incoming calls to work with Asterisk...but I still can't get Asterisk to answer incoming call on Linejack's LINE port. I attached a phone set to the PHONE port, and telco line to the LINE port on the Linejack(ISA) card. I have downloaded, compiled and installed the newest driver for

Hi! I've bought a Wildcard X101P card to play a bit with asterisk. I'm just trying to place a call to a number, wait until the receiver takes the call, and then play one of the .gsm sound files. I'm in France, so first I tried modprobing wcfxo with opermode=1, but the DAA mode remained FCC, so I changed the opermode variable in wcfxo.c to 1 by hand and recompiled & reinstalled

-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 I'm experiencing frequent kernel panics when using the X100P card under the 2.6.6 Fedora kernel. I've attached the kernel output to this message - - it looks like the IRQ stack is overflowing and trashing some memory, causing a series of oopses followed by a complete crash. I have just hacked the kernel to reenable 8k stacks and will see

I'm trying to use a shareware program called PowerISO to extract a .daa cd image to a raw iso9660 format so that I can view the contents. PowerISO runs like this: ________________ [nate@blackbox ~/.wine/drive_c/Program Files/PowerISO]$ sudo wine cdburn.exe Password: Usage: cdburn <drive> -erase [image [options]] cdburn <drive> image [options] Options:

1. I noticed that... - after cold booting the host, I see successful Dahdi/wcfxo messages in /var/log/messages - then, if I run either "/etc/init.d/dahdi restart", or "/etc/init.d/dahdi stop; /etc/init.d/dahdi start" without waiting more than about 10 seconds between the stop/start commands, I get the familiar error messages "DAHDI_CHANCONFIG failed on channel 1: No such

Hi, I using asterisk 1.2.4 on a CentOS with Linux 2.6.9-22.0.2.ELsmp kernel. I've two x100p cards connected, only one card is reconigzed by asterisk. 02:01.0 Communication controller: Tiger Jet Network Inc. Tiger3XX Modem/ISDN interface 02:02.0 Ethernet controller: Davicom Semiconductor, Inc. 21x4x DEC-Tulip compatible 10/100 Ethernet (rev 31) 02:03.0 Communication controller: Tiger Jet

Hi Last week I installed Asterisk (release1) with digium t100p single span T1 (wct1xxp) board on Dell GX270 pc configured for PRI. Asterisk/t100p is currently the only user of the t1 line. All worked well for about a half a day, PSTN to SIP phones to non-SIP IP phones etc. Alas, since then I consistently get multitudes of blue alarms on all b-channels followed by a loss of d-channel: Aug 31

Hi, I have already installed the X100P drivers but when I make to make call call, I always get No channel type registered for 'Zap'. Any idea how to solve this problem? It seems that the Zap module is not loaded but I have already load the driver by modprobe zaptel > modprobe wcfxo > ztcfg -vv thanks -------------- next part -------------- An HTML

Hi, I've been trying to get my zaptel x100p cards working for the past week now. this is what I've done: installed asterisk: make clean make linux 26 (for fedora core 2) make install installed zaptel: make clean make make install did a modprobe zaptel, and wcfxo got this in /var/log/messages: PCI: found IRQ 11 for device 0000:00:0f.0 wcfxo: daa mode is 'FCC' found a

Hi, One of my pbx's seems to be having some new issues. crackling interference on the zap channels running through the channel bank, and I noticed that these happen when I hit an "irq miss" in zttool: Current Alarms: No alarms. Sync Source: Digium Wildcard T100P T1/PRI C IRQ Misses: 82695 Bipolar Viol: 0 Tx/Rx Levels: 0/8 3 Total/Conf/Act: