similar to: DID line with Adtran TA750 and T100p

Hello, So all the pieces are finally here, and I'm ready to play. I remember reading on this list that the connection Channel Bank <-> T100P requires a "reverse cable." Is this a regular Ethernet reverse cable (i.e., only a couple of pairs reversed?) Please help me before I blow something up! Saludos, Jose.

Hello all, I've got a T100P connected to an Adtran TA750 with a T1 crossover... This connects to a patch panel with phone ports. The Adtran is fully populated with FXS cards. All I get on any phone port is a fast clicking noise... No dialtone. Asterisk 'sees' the card, (the channels show up in /proc/zaptel). Incoming calls are routed to the zap/x channel, but no ring. I'm

Hello Everyone, I am new to asterisk and linux too, I managed to installed asterisk on redhat8 with the help of mailing list archives and Handbook guide. I configured 2 SIP phones (grandstream) and it is working fine internally. We have T1 Line coming in with block of 200 DID Numbers. I want to assign DID Numbers to each of SIP phones as an extensions and able to call any PSTN line.

(to mods: sorry for any extra work I've put you through. Posting from my work account, as proper) Hello all, I'm back. I've got that lucky feeling that this will all work out very soon, and I hope that that is true. The issue: In my * server I have a t100P, connected with a T1 crossover cable to an Adtran TA750 with 2 FXO cards. After I do 'modprobe wct1xxp;ztcfg' the alarm

Rich, Thanks a bunch, totally understand now and that actually makes total sense. (no need for schematics). This also explains why I used an TA750 to go into a Nortel MICS system, using FXO and no buzz. Totally balanced load from the analog ports on the Nortel across the 5 feet of CAT5 to the FXO on the adtran. Now I need to get rid of some Adtrans --- Anyone lookin to buy? :) Thanks

Hello. I have been going thru the wiki and asterisk related sites and have not been able to find any documentation about how to configure an Adtran TA750 channel bank. The remote disconnect supervision doesn't seem to be working, when the remote caller hangs up asterisk takes up to 30-45 seconds to hangup the call. Can somebody help? Thank's

All, I need help. I have an (actually 2) Adtran TA750's with 8 FXO ports. I get a terrible buzz on every FXO port. If I unplug the Adtran and put an analog phone on each incoming line, I have no buzz. I also have 2 Carrier Access Access Bank I's with 12 FXO ports. When I plug the same analog lines into either one of those, no noise or buzz whatsoever. I went so far as to move the TA750

I believe it is not fiber, but I am not sure. I am going to take one of them home tonight and hook it to my POTS line there, which for sure is not fiber. Gregory P. Scasny Golden Technologies Inc. http://www.golden-tech.com 219-462-7200 -----Original Message----- From: asterisk-users-admin@lists.digium.com [mailto:asterisk-users-admin@lists.digium.com] On Behalf Of Michael Welter Sent:

I recently set up Asterisk with an Adtran TA750. All is well except the phones do not show the MWI. I have configured zapata.conf properly, as all phones will receive a stutter dial tone if there is a message waiting in it's assigned mailbox. Does anybody know how I might fix this problem? Thank you for your time __________________________________ Do you Yahoo!? Yahoo! SiteBuilder - Free,

Hello, I have just received Adtran TSU 600 with 24 FXS ports. I have installed sucessfuly T100P card. Adtran is connected to t100p with crossover T1 cable. On T100P card I have a green light and on Adtran I do not get any errors or alarms. But I do not get dialtone on FXS ports. Adtran is configured: For Network Timing, fxs ports ore fxs_ls on Adtran. In zaptel.conf: span=1,1,0,esf,b8zs

I have following setup Asterisk - T100P -> Adtran TSU600 P + FXOcard -> PSTN line When PSTN line is plugged directly in to analog X100P caller id is received by Asterisk but when I plug it into adtran I'm not getting caller id. Any ideas what kind of setup Adtran TSU600 requires to pass caller id to T100P ??? regards m.

Hello Can somebody send me please config files of zaptel.conf and zapata.conf for adtran fxs ports. I cannot make it work. I do not get a dial tone on Adtran and when I am trying to call from sip i get: app_dial.c:674 dial_exec: Unable to create channel of type 'Zap' == Everyone is busy at this time There are no errors on T100P and adtran. Please help! B.

Skipped content of type multipart/alternative-------------- next part -------------- No virus found in this outgoing message. Checked by AVG Anti-Virus. Version: 7.0.298 / Virus Database: 265.6.4 - Release Date: 12/22/2004

I have a T100P card connected to an Adtran and then a T1. I have added the following configurations to Asterisk...but, when I dial 9 and then a local phone number, it bounces between the dial tone and silence and the *error* light on the Adtran blinks. zaptel.conf span=1,0,0,esf,b8zs fxsks=1-8 loadzone=us defaultzone=us zapata.conf [channels] context=from-sip signalling=fxs_ks

>>TURN OFF HTML!!!!!!!!!!! >>Why the hell do you feel I need to read your text in a lightish blue >>color???????? Do you know how shitty that looks compared to everyone >>elses black on white. Blue doesn't offer the contrast my eyes prefer. So >>why the hell do you feel important enough to override my defaults? You >>sir are the annoying guest who comes in

Hello All, I've mostly solved my DID problem from a few days ago. Apparenly the lines weren't configured properly. Now heres the next question. 12 E&M wink lines from telco. I have them all plugging into an Adtran 750 with FXS cards. The Adtran ports are configured DPO. How do I signal this from Zaptel. I have them setup E&M in zaptel.conf and EM_W in zapata.conf. They

Jay, I have had a lot of trouble with the FXO ports on Adtran TA750. Unless the incoming POTS lines have a balance impedance, they will buzz very bad. Gregory P. Scasny Golden Technologies Inc. http://www.golden-tech.com 219-462-7200 -----Original Message----- From: asterisk-users-admin@lists.digium.com [mailto:asterisk-users-admin@lists.digium.com] On Behalf Of Jay Milk Sent: Sunday, April

I've been working with an adtran ta 850 hooked to a t100p pretty much all day today, and I haven't gotten past configuring zaptel.conf and zapata.conf. For some reason, when I pick up analog phone hooked up to the first module of a quad fxs card in the second slot of the ta 850, asterisk thinks that all four of the fxs modules in that card are going off hook. If I pick up a phone hooked

Hello, We keep having a really bad static problem on phone calls completed using a Adtran TA750 and T100P card. The phones are Polycom IP 500 phones and, it occurs across all phones. Not just one. Everything appears to be on it's own interrupt. I noticed the last time we did this, we rewired everything to make sure it wasn't an electrical issue. Well about a month and a half later

Hello, Did anybody successfully tried upgrade Adtran TSU 600 to firmware which is working properly with T100P and asterisk ? B.