similar to: T100P & Phones Configuration

Hi, I have scanned through the archives of this list and found a number of question about hardware, but I just can not find the answer to my question. I am new to phone systems, I got "drafted" to come up with a new phone system for our company (I guess they figure since I know computers I know phone systems as well :O). We have 5 analog (I guess they are called PSTN lines) lines coming

Hi Everyone. I have a client that uses an Altigen system. I am really new to PBX systems so all this is totally foreign to me. They currently have 5 inbound trunk lines and about 20 analog phones. >From what I can gather they are using the Altigen Quantum cards that support 8 extensions and 4 trunks. >From what I can gather the solution is a TDM04B and TDM01B to bring in the lines from

Hello all, I've got a T100P connected to an Adtran TA750 with a T1 crossover... This connects to a patch panel with phone ports. The Adtran is fully populated with FXS cards. All I get on any phone port is a fast clicking noise... No dialtone. Asterisk 'sees' the card, (the channels show up in /proc/zaptel). Incoming calls are routed to the zap/x channel, but no ring. I'm

Hello, I don't have any experience with channel banks and would appreciate any feedback on my theory outlined below: We have a single T1 entering the building with channels 1-12 being voice lines and 13-24 being a 768k internet connection. This T1 terminates to an Adit 600 (T1-1). Here's what I know. Channels 11-12 go out the Adit 600's 25-pair connector to a wiring block (and

OK, I think I'm ready for the next step from the X100P. Splitting a T1 with a T100P and a channel bank/s ~ 50 extensions. I think the existing system uses NEC phones for ~34 extensions, I don't know the specific model yet of the phones or the channel bank. If the channel bank is not compatible with Asterisk/digium what brand should I be looking at to interface best with Asterisk and

Hi all, I've seen a couple of posts recently from people who are doing something with Asterisk and a T100P and a Nortel PBX. However it's not clear exactly what they are doing. Does anyone know if it's possible to use a T100P or T400P as a DSX-1 interface to connect to a T1/PRI CO module in a Nortel PBX? We have a Nortel Norstar Modular ICS PBX and I'd like to plug its CO

I've tried to figure out from the web site the minimum hardware cost to run a small office Asterix solution but I'm afraid I miss something: Let's say that I want to connect four/five analogic extension to the PBX. I have: - 1 computer as the server (with linux and Asterisk on it) - 1 dummy patch panel to connect all the analogic phones around the office What (and how many) cards

Hello all :) I've just been handed a project that I need to get working pretty quickly. Basically I have four "analog DID trunks" for incoming only calls coming in. I know that these are Loop start with Wink start, and that after wink they send a 4-digit id number. Is this something that the Wildcard boards are able to handle and that Asterisk could interpret? The digits

Greetings, According to the FAQ "When you load the module and have no circuit/channel bank the LED's should flash red" I get the "knight rider" lights before the module loads, but after the modules are loaded I don't get any lights, other equipment plugged in or not. The card has been on my shelf a while so I wonder if it needs a firmware upgrade ? Can the cards

Hello, So all the pieces are finally here, and I'm ready to play. I remember reading on this list that the connection Channel Bank <-> T100P requires a "reverse cable." Is this a regular Ethernet reverse cable (i.e., only a couple of pairs reversed?) Please help me before I blow something up! Saludos, Jose.

Skipped content of type multipart/alternative-------------- next part -------------- No virus found in this outgoing message. Checked by AVG Anti-Virus. Version: 7.0.298 / Virus Database: 265.6.4 - Release Date: 12/22/2004

Hello, Again one more question about hardware. What could you suggest me to buy. I need hardware to connect let's say 4 analog lines. (FXO). This hardware should "talk" to Asterisk of course.. Thanks very much for some advices :) Bartek -------------- next part -------------- An HTML attachment was scrubbed... URL:

Hello All, I could use a recommendation if anyone has a moment. I have the T100P but I have not gotten my service yet. I want to have at least 12 lines of digital voice with DID. Should I just seek out a PRI ISDN provider or is there something else I should look for? I want to keep cost as low as possible. Also, I want to own my own router for the phones since it is always a hassle to get

I'm unable to get faxes working over tdm400p (4fxs modules) Too many errors sending and receiving faxes with an analog fax 1) echocancel=no on the zap channels 2) ztmonitored the channel for a good/low audio volume I'm trying to send fax between zap fxs channels. No way to get it working right Has someone else the same problem?

I have a nice used zhone channel bank I want to experiment with, but need a T1 interface for my * box to do so. The TE410P looks nice, but more money than I want to spend to experiment, and I don't need 4xT1, only 1xT1. Are there any good 1xT1 PCI cards that are recommended? Regards, -Dorn

Everyone-- Here's a cost analysis, rather crude and inspecific, of using Asterisk to implement a phone system. I'm really quite naive and new to all this, so I'd appreciate any corrections, tips, pointers, etc, from those in the community, who have far greater experience, knowledge, skill, etc. than I. Am I forgetting something important? Am I way off in my estimates? The Minimum

I know a few ppl have those CAC Adit 600's with t400 I can't seem to get my second span up on the T400 connected to the second spand on the adit (A:2) A:1 seems ok Can someone post they zaptel.conf span defintions And maybe a "print config" from the adit 600 cli I think my issue is timing srcs the coding, framing. bld out are all matched thx -------------- next part

Is there something special that needs to be done to allow a T100P/T400 to respond to a remote loop request? I am having some issues with a Point to point T1 line using zaptel ppp. This line gave us small problems when we had a pair of Cisco 2600's on either end but now with the zaptel ppp it is going down every couple of minutes for 15 intervals. The phone company says the line is good to

I have a couple of live T1s sitting around and they are not ISDN(like most of the people that are using Asterisk seem to be using), they are regular old 24 channel, robbed-bit, E&M wink start, D4AMI T1 circuits. Can I get these T1s to work with a T100P Digium card and asterisk? Searching through the lists and the documentation I haven't seen any examples of how to configure this kind