similar to: Noise with Grandstream/PSTN

I've done all the googling I can on this, and have come to the conclusion that a Grandstream BT101 can be abused to be a door phone. Could someone with access to one, confirm that the following is possible? Researched: 1. When set to auto-answer, dialing the phone will result in a short beep and instant speaker-phone connection. 2. When pressing the "message" button while

I've seen lots of stuff go around about Grandstream firmware levels (in my case specifically the BT101/102). I'm just wondering what the currently accepted 'best' firmware version is to use? After seeing stuff going around about buggy firmware I want to know what I'm getting into before upping past my current 1.0.5.11. It's relatively stable, and the last thing I want

Hi, I'm confused as anything by this bug. I'm hoping that it is just something screwy in my config. I have 1 Cisco 7960 and several Grandstream BT101 & 102's, and a Digium TDM31B. I'm running the latest CVS (CVS-HEAD-05/27/04-17:22:40) of both Asterisk and the Zaptel driver on Fedora Cora 1. When I make an outgoing call on the Cisco phone, everything works fine. I'm

I've searched the lists but I didn't find anything exactly like this. I have two Grandstream BT101 phones connected to an Asterisk. Periodically, for reasons that I can't determine, one or the other (or both) of the BT101s decide(s) to go on permanent busy. Dialing that phone gives: -- Executing Macro("SIP/24567-7856", "dialphone|SIP/27654") in new stack

Hello List, I have used isolinux for years without problems. Recently I decided to upgrade from 3.09 to 3.11. Every CD I create can be read on my Vectra (Pentium 3) and all other Pentium 3 boxes, but all my Pentium 4 boxes will not boot (they ignore the CD and boot from hard disk). The bochs VM will boot the CDs fine just like the Pentium 3 machines. I have tried 3.09 (which worked

Hello, Has anyone noticed that if you don't pick up a BT101 phone in 60 seconds it stops ringing and acts like it was never called ? Or is it just something I missed ? If it matters for something I have call waiting enabled on the phone. Product Model: BT100 Software Version: Program--1.0.5.11 Bootloader--1.0.0.18 HTML--1.0.0.37 VOC--1.0.0.6 Custom Ring Tone:

In the following scenario, the user calling from a SIPphone registered phone is able to transfer the called user to another extension. sip.conf: [general] port = 5060 context = from-sip register => number:password@proxy01.sipphone.com extensions.conf: [from-sip] exten => s,1,Dial(SIP/111&SIP/117) exten => 111,1,Dial(SIP/111,20) exten => 117,1,Dial(SIP/117,20) 1. The calling user

Hello, I resolved my echo issue using grandstream/estara etc etc sip phones and wcfxo interfaces from digium. I swapped out my via kt400 based msi kt4vl motherboard for an asus p4pe? i845? based motherboard and the echo has completly gone away along with aggressive suppressor option in the makefile. I hope this helps others. Brian J. Schrock Anistone Technologies, LLC 6926 Avery Rd. Dublin, OH

Original Post ---------------- I have an Asterisk related problem with mutualphone. I can connect to any number with any softphone that I am using (iaxcomm, SJPhone, and a few others). Also I have a Grandstream BT 101. But I cannot call (via Asterisk) to mutualphone destinations. Other destinations go fine. A working phone call (e.g. from iaxcomm) gives the following on the console: --

Hello friends, I'm having a problem with my home server (ASUS A7V133 motherboard) which has a horrible performance with ATA disks connected to an integrated promise controller. Below you can see iozone results of the same disk connected to the primary/ secondary controller versus the promise one. Promise ATA100 controller: ========================= Version 1.02a ------Sequential

Hello all, This email is intended rather informative than questioning. While developing some script-generated dial plan, we figured out that there are differences between Snom 190's and BudgeTone 101's relating to transfers. It appeared that the 190's will have their own 'Caller ID' set as the 'CALLERID' variable in astersisk when transfering a call, while the

Hi, I'm testing a Polycom IP600. With firmware version 1.1 the phone reboots at any time. With firmware version 1.2, the first reboot was an endless reboot. Then I moved the phone to another lan port, then it worked fine. Then I installed again in the initial lan port and the phone works well. However after some time of inactivity (1 hour?), the IP600 stops to send and receive calls.

Hi folks -- I'm trying to share out my home directory and one other directory from an SGI O2 running IRIX 6.3 to an HP Vectra running Win NT 4.0. I'm having some problems and would appreciate a hand. I've read the man pages, DIAGNOSIS.txt, the FAQ, and most of the other documents in the distribution. My problem is probably a simple configuration issue, but I haven't been able

Hi, I came back from a quiet weekend today and found my E400P box to have gone astray. Asterisk is loaded from inittab, and started crashing and reloading a couple of thousands of times, each time notifying my monitoring service :-P I remember there would be issues on old cvs stuff since the crash at digium so I made a clean checkout just now. Here is what happens when I load manually:

Any ideas ????? Jonn -------- Original Message -------- Subject: [asterisk-users] Internal LAN echo problem Date: Wed, 24 Oct 2007 08:34:32 -0500 From: Jonn R Taylor <jonnt at taylortelephone.com> Reply-To: Asterisk Users Mailing List - Non-Commercial Discussion <asterisk-users at lists.digium.com> To: Asterisk Users Mailing List - Non-Commercial Discussion <asterisk-users

Ok. I just got a TDM10B and it is in with my X100P. So as it says in the provided instructions, I used the command modprobe tor2 I get an error message saying that there is no such device. My zaptel.conf looks like this: fxsks=1 fxoks=2 So I load the X100P first. (modprobe wcfxo) Then I load the TDM10B (modprobe tor2) Then I'm told that the device doesn't exist. Please help

Is this supported? I have a very simple setup where I have 2 X100P cards and a TDM10B. The TDM10B is connected to a phone that has a digital answering machine built into it. If I make an inbound call on either X100P interface it gets transferred to the TDM10B interface. If I let it ring the TDM10B interface answers the call and the greeting message of the answering machine starts. Then shortly

Greetings! I have made great progress thanks to this group. My Asterisk seems to be working for the most part. I am using the following equipment/software: * HP Vectra VL - Pentium Pro CPU - 256MB RAM * Redhat Linux 8 - Loaded straight from distro CDs as Developer Workstation - latest updates from RHN * Asterisk (latest as of two weeks ago when I used CVS checkout) * X-Lite SIP Client on a

I just spent the last hour or so trying to get this firmware to work across a NAT with no success. I have a GS BT101 working through the same NAT, so I don't think it's the NAT itself. I have a STUN setup in * and pointed the UIP200 to it and I tryed several combinations of nat= in the sip.conf and in the config files for this phone. No luck(yes, I did a reload now with each change in

Hello All, I am looking for a way to do priority call ringing. That is when a caller places a call to another party, they can indicate that the call is a priority and get a different ring to occur (ring cadence) on the called parties phone. This would be synonymous to an intercom ring on a key system. After some investigation, I have come across the ability of the GS BT101 which will ring