similar to: My linux machine thinks its running windows!!! It crashes... (Problems with my x100p card.)

For those that have had X100P echo problems, it seems that somewhere just prior to Asterisk CVS-12/04/03-14:24:40 it has been fixed to where its hardly detectable for just a couple of seconds at the start of a call. (I use to have it rather bad for the first 15 seconds or so.) I'm using DECHO_CAN_MARK2 with KFLAGS+=-DAGGRESSIVE_SUPPRESSOR and echotraining=yes echocancel=yes

We have been pretty much able to solve our echo problems, except for the primary mode in which we desire to operate our system. See system diagram at bottom. Prior to making adjustments to cancel echos (all echocancel=no): Call Type Result (Before) --------- --------------- CP <- LEC PRI * TDMoE * FXO -> AP

After speaking with several people, and even participating in a forum of several other people with echo issues, I thought I'd share what we've done (well actually what our chief R&D engineer, Brett Bourn has done...) First let me say that normal cheapy PC hardware couldn't be made to function with out echo. We tried on both the single port Digium T1 card and the 4 port Digium T1

I notice the zaptel Makefile option the mark2 option & KFLAGS+=-DAGGRESSIVE_SUPPRESSOR is now gone. Does simply adding these options still compile in a certain echo can - or is there an other method of activating a particular can. I have not had to update my machine that is connected to pstn for a while & I don't want to jump into echotraining without a way to quickly enable what has

I've got * up and running everything seems to work ok except for when you dial out using the X100P card. Everything sounds great this end but the person you call complains that they can't hear you very well (Very Whispered). Is their any way to turn up the volume. I've fiddled with the gain settings in the zapata.conf file but to no avail. Any help would be much appreciated! -Ed

Yo all, I have a problem with a Dutch (KPN) PSTN-line, connected to an X100P. The call wil sound OK at first, but after 10-20 minutes, the audio will start to crackle. Soon after that, this crackle turns into a continuous noise and the parties won't be able to hear eachother anymore. It also sometimes happens that the party on the TDM400P hears a very loud, short-delay echo of themselves,

Hi All, I have a Soekris 4801 running Asterisk and I tried to add a X100P FXO card only to find that the Soekris will not boot with the card installed. The LEDs flash for a second and then nothing, it does not boot. I've tried 2 different X100p cards, both of which work in a regular desktop system, and still have no luck. I tried a different Soekris 4801 with no luck. I've also tried a

With the 1U Apple G5 server at a good reliability/storage/pricepoint level... got to thinking about compiling Asterisk on OS X.. at least for SIP phone call switching, voicemail, etc. Has anybody attempted this? Email me off list if this is too dev-heavy for the user list. Thanks, Ted W -----Original Message----- From: asterisk-users-request@lists.digium.com

Hi, I have problem with X100P clone card.I can not force it to work under Asterisk 1.4.27.1 and DAHDI Version: 2.2.0.2. I looked over and over on configuration and could not see any mistakes. Here are relevant configuration files. /etc/dahdi/system.conf > fxsks=1 > echocanceller=mg2,1 > loadzone = hu > defaultzone = hu > dahdi_tool > OK Wildcard X100P

I'm testing out my SNOM 200 phone by trying to call out through NuFone. When I do so, I don't hear an echo at all (in fact I can't hear myself through the phone) but the callee can hear an echo when she speaks. NuFone tells me their network is totally digital and so can't be involved in an echo. This is all well and good, but the echo is still there. Any suggestions? As a

Hello my brothers and sisters, Is "X100P" card suitable to VoIP? and if "yes", am i need to only "X100P" and "Asterisk" Package? or i need also to other cards or packages? and if "X100P" card not suitable to VoIP, please recommend a another card, (please take in your account that i would like to connect standard analog line to the card

To the guy who wanted to know if the Tiger 560 card was a X100P - I don't think so. Here's the lspci -vv from a fairly new X100P: 00:09.0 Communication controller: Tiger Jet Network Inc. Model 300 128k Subsystem: Unknown device 8085:0003 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B-

Looking at installing Asterisk and have not been able to find any info on "minimum" or "recommend" system hardware. I have a box P200MMX 128mb 4.5gb HDD which is running Redhat 8.0 fine. Noticing on the Digium web site it mentions that the single fxo card (Wildcard X100P) requires a minimum pIII 500. Is my intended box going to be too slow? My application is a small level,

Hi all, I'm having a problem with * being very finicky about the length of DTMF key-presses during menus, voicemail, etc. Basically, short (<100 ms) tones are ignored, anything between 100ms (or so) and about 300ms is correctly detected, and anything >300ms is interpreted as multiple presses of the same key. This is terrible for callers who are trying to get to the correct

Hi, all I only have x100p card, and my pc doesn't have sound card. How can I make a call and accept a call with x100p on my pc through the telephine line? If these tests are passed, I can get more money to buy a TDM 400 card and a sound card, even an IP phone. Any one can help me? I installed Redhat Linux 9.0 on pc. Thanks in advance. Best, Michael --------------------------------- Do

I'm trying to get the X100P card working in AU. So far I have managed to get it to handle incoming calls from the PSTN and have managed to eliminate pretty much most of the echo. My big problem is getting the outbound calls to work. When I get ZAP to dial out it won't connect and I get what I think is the Congestion signal - like a busy signal but with what appears to be a 10db

Ok, I have 2 PC's that are identical. I loaded Redhat9 on the first and Asterisk and installed a x100p card and it works fine. I ghost the first PC and install the ghost on the second PC. Everything comes up on the 2nd PC but I can't get it's x100p card to load. The systems sees the card, it's on interrupt 11. It shows up in /proc/pci and /etc/sysconfig/hwconf and lspci shows it

Hi. I have a x100p card installed on my asterisk box... my zapata.conf file includes the following lines: [channels] context=default switchtype=national signalling=fxo_ls rxwink=300 echocancel=yes rxgain=0.0 txgain=0.0 group=1 callgroup=1 pickupgroup=1 Basically, the zapata.conf file generated by make samples. Then in my extensions.conf I have this: [default] include => demo And demo is

Heya all, I'm experiencing some problems with a TDM40P and was wondering if anyone else on this list has similar experiences, or maybe even a possible solution. My setup is a dual PIII-750 with 1 gig of RAM, with an X100P, connected to an analog line to my telco, and a TDM40P with analog phones connected. The TDM-card is not sharing any interrupts, but the X100P is, with the 2 Adaptec SCSI

Hello. All. I am a bit new to asterisk, started from half a month ago. I am setting up a home asterisk server with analog card. I am using asterisk 1.4.27. At the moment, I bought a X100P card and installed it on my computer. I used it to connect my home phone line. For the moment, it works fine when dial in. Soon I noticed when I dial out through it to my mobile, it can't hang up