similar to: additional ports for devkit tdm400p(tdm10b) ?

Ok. I just got a TDM10B and it is in with my X100P. So as it says in the provided instructions, I used the command modprobe tor2 I get an error message saying that there is no such device. My zaptel.conf looks like this: fxsks=1 fxoks=2 So I load the X100P first. (modprobe wcfxo) Then I load the TDM10B (modprobe tor2) Then I'm told that the device doesn't exist. Please help

Hi all, I have just purchased the DevKit from Digium and received a X100P and a TDM400P (it has one FXS module). The problem is that I can't get the kernel module (wcfxs) to load and run. I have searched the archives and can't find anything about this. Do the messages below ring any bells with anyone ? There is no interrupt clash (see pci list below). I am running on a AMD 1.2G

I was considering buying a devkit, bit it looks like it's not longer available. Will there be a replacement devkit? If not, where to buy a reasonable priced channel bank? Which channel bank was included in the devkit and where can it be bought? (btw I live in Holland) Chris

I've been having trouble with a TDM10B that I installed a few days ago. At first I could not modprobe it at all (getting the errors below). I switched the X100P that was also installed (with a Motorola chip) with one with a Tiger-something chip, and then everything starts up okay. However, after a few hours, the FXS port dies (no battery or anything), and if I try to rmmod & modprobe

Hello all, New to the list, Asterisk and this wonderful world of convergence. From reading the docs, list and websites I hopefully correctly understand that I can use a plain cheap isdn4linux supported ISDN (passive) TA to hook up the PC to the ISDN line from the telco (FXO card?). Next in the PC I also need a FXS card like a Digium TDM10B or PhoneJack so I can hook up an analog phone to it. In

Semi-offtopic, Anyone know of voip providers who can provide tollfree number service? E.g. route 800-xxx numbers to our * ? Even better if they are familiar with * or can speak IAX ... -Dan

Is this supported? I have a very simple setup where I have 2 X100P cards and a TDM10B. The TDM10B is connected to a phone that has a digital answering machine built into it. If I make an inbound call on either X100P interface it gets transferred to the TDM10B interface. If I let it ring the TDM10B interface answers the call and the greeting message of the answering machine starts. Then shortly

Greetings: ------------ BACKGROUND -------------------------- I am using the Monta Vista development kit on an Intel RedHat Linux platform... the target is PPC_405. The configure utility that comes with the openssh-3.5p1 code will not support cross compilation. It gives an error message about not being able to test its results and then exits before it creates a Makefile. To get around this

I need to generate a minimal Samba working in a SH4 cpu in a STLinux 2.3 environment. The goal is to have very very simple Samba server running in a STLinux environment. STLinux Kernel has included the CIFS support. Really I'm a newbie in Samba cross-compilation. And obviously I've problems :-( Any help will be appreciated. Thanks :-) 1) First of all I've set some env vars: export

Is there anything special needed to load up a TDM10B card?? I got the card today.. Took it from the box, put it into a PCI slot.. connected the power to the card and booted the PC.. I have removed the X100P to avoid confusion and I have the following in the config files.. in /etc/zaptel.conf # For the X100P #fxsks=1 # For the TDM10B fxoks=1 in /etc/asterisk/zapata.conf [channels]

Any details yet? -Dan

Hi, Would someone assist me with the configuration of my TMD10B and X100P cards? I would ask Digium but my support was good for only one install...( I had to rebuild my * box). I wrote down the configuration but I must have made a mistake somewhere. I have followed the instructions on the Digium site but I must be missing something. Here's the config (snippets) I've been attempting to

So I have an X100P, and a TDM10B both working (at least I think they are). The drivers have been loaded and ztcfg -vv shows no errors in the configuration of two channels. When I run asterisk -vvvc and pick up my phone (plugged into TDM10B), I don't gear a dialtone. in phone.conf, I have [interfaces] mode=dialtone format=slinear ... Shouldn't that produce a dialtone when I pick up the

I installed the TDM400P and installed it on a system running on Fedora Core1, please refer to the steps below. I connected an analogue phone to the FXS port. When I pick up the speaker I don't hear the dialtone although when I press a number key I hear a DTMF generated. What could be the problem? I appreciate your help 1- First I installed the TDM400P in the PCI slot and connected

I'm trying to install on a 233Mz PII running RH7.1 kernel 2.4.2 The "astinstall" script pulled files from CVS ok and compiled with no warnings. When I try to run "modprobe wcfxo" and "modprobe wcusb" I get the following identical set of error messages: 15. Creating sample environment...SKIPPED ================= Installation Completed! ====================

Hi Lars, people. I''ve realized that currently the gem(version 1.6.26) doesn''t work with Ruby 2.0.0 in Windows 32 bits, neither the 64 bits version, I''m talking about the versions listed here: http://rubyinstaller.org/downloads/ . There you can see both versions of Ruby and also the both versions of the DevKit: mingw64-32 and mingw64-64. I''ve tested with both

Just a warning to dovecot listmembers. The list is being harvested. test3943395 is a unique address I created only for communication to the dovecot list. The following spam came from: Received: from dial-dynamic-62-69-52-187.surfdial.murphx.net (dial-dynamic-62-69-52-187.surfdial.murphx.net [62.69.52.187]) by sasami.anime.net (8.11.6/8.11.6) with SMTP id j7FLxtv03775 for

Ok. I am confused. I now have conflicting answers to my question: Do you need to use a special phone to use SIP? My setup is X100P and TDM10B. I would like to connect to iConnectHere, which uses SIP. Has anybody done this before (using similar equipment to what I have listed above)? And if it is not possible, could somebody please explain why. I don't understand why this wouldn't

Hello Everyone, I just got my Dev Kit TDM today... :D I installed the X100P ok (wcfxo); however, when I tried to 'modprobe wcfxs' for the TDM400P(TDM10B), I got this error message: /lib/modules/2.4.19/misc/wcfxs.o: init_module: No such device Hint: insmod errors can be caused by incorrect module parameters, including invalid IO or IRQ parameters /lib/modules/2.4.19/misc/wcfxs.o: