similar to: Zaptel.conf & digium E100P

All, I'd like to buy an E100P Wildcard frm Digium, but i prefer to buy it in Europe (costs, ...). Could somebody point me to an european reseller ? Thanks in advance. -- Nicolas Cartron nc@ncartron.org

Hello ml, i need some help on my zaptel configuration. My E100P only shows some YELLOW / RED alarm when I load the wct1xxp module and do a cat /proc/zaptel/1 Span 1: WCT1/0 "Digium Wildcard E100P E1/PRA Card 0" HDB3/CCS YELLOW RED ... .. . My /etc/zaptel.conf is: span=1,1,0,ccs,hdb3 bchan=1-15,17-31 dchan=16 loadzone=nl defaultzone=nl I tried zaptel-1.0RC2 and the latest CVS

Hi, I'm having trouble configuring and E1 link , I know the E1 is a PRI and the switchtype is 5ess. The problem is that everytime I try to dial I got and error saying that it was unable to open the zap channel . Devices are created in the /dev/zap directory and I can open them with a cat /dev/zap/1. I can also see the channels in /proc/zaptel/1. Thanks in advance [zaptel.conf]

Hello list, i've got some problems getting a E1 line with a E100P up and running (germany). # cat /proc/zaptel/1 Span 1: WCT1/0 "Digium Wildcard E100P E1/PRA Card 0" HDB3/CCS/CRC4 YELLOW RED "YELLOW RED" sounds not so good. When launching asterisk, enabling pri debug on that span, i see outgoing attempts: ;---------- snip -------- > [00 01 7f ] > Unnumbered

Folks, everything's in the subject, i've got a Linux Box with a Digium E100P E1 Card, modules are loaded, but I don't know which signalling to put in my zapata.conf... Thanks for you help. -- Nicolas Cartron nc@ncartron.org

Hullo everyone, Iam new to Asterix but am trying to get R2 signalling working with a Digium E100P E1/PRA Card. My Telecom doesn't have an implementation of ISDN PRI yet, so it's R2 that is supported. Could anyone have a patch to fix this for me. Am told it has something to do with Assembly Language programming. Please help me fix this. Regards, Nicholas

On the /proc/zaptel it was lost interrupts, you haven't got any so that's good! On opencall.org there's a known issues link and that mentions some fax machines that have issues, might be worth a quick check there. I can receive from our fax machine this end, if you'd like I'll send you a test fax if you send me your fax number, if you can receive from us and tpc then it's

Hi Last week I installed Asterisk (release1) with digium t100p single span T1 (wct1xxp) board on Dell GX270 pc configured for PRI. Asterisk/t100p is currently the only user of the t1 line. All worked well for about a half a day, PSTN to SIP phones to non-SIP IP phones etc. Alas, since then I consistently get multitudes of blue alarms on all b-channels followed by a loss of d-channel: Aug 31

I have configured /etc/asterisk/zapata.conf, but now Asterisk refuses to start: Asterisk 1.0.9, Copyright (C) 1999-2004 Digium. Written by Mark Spencer <markster@digium.com> .... [chan_zap.so] => (Zapata Telephony w/PRI) == Parsing '/etc/asterisk/zapata.conf': Found Sep 16 20:36:51 ERROR[6750]: chan_zap.c:6246 mkintf: Unable to get parameters Sep 16 20:36:51 ERROR[6750]:

<P>hi Everyone,</P> <P>We are configuring an ISDN PRI E1 with an E100P card, when you load the drivers, and starts the asterisk, cards also starts fine, givin following output,</P> <P>*CLI> <BR>&nbsp; == D-Channel on span 1 up<BR>&nbsp;&nbsp;&nbsp; -- B-channel 1 successfully restarted on span 1<BR>&nbsp;&nbsp;&nbsp; --

I have a user, running CVS a/o 11/23/03, who has complained about "phantom" messages showing up days or even weeks after she has deleted them. So I asked her to let me know when it happened again, and she called a few minutes ago. The directory listing below shows a listing of the /var/spool/asterisk/voicemail/default/XXXX/Old directory, and to my surprise the messages are indeed

Hola! I've a Digium E1 card, zaptel recognizes it as (loading the module with debug=1) Setting up DMA (write/read = 321b2000/321b2200) Controller version: 43 Framer: DS21554, Revision: 5 (E1) Found a Wildcard: Digium Wildcard E100P E1/PRA Using CCS/HDB3 coding/framing with CRC4 120 Ohms Calling startup (flags is 4099) Started DMA Got interrupt: 0x0005 /etc/zaptel.conf:

Hi, I am trying to track down the reason to my problems with sending and reciving fax with my PRI and 2 TDM400P Cards: PSTN <-> PRI (E100P) <-> * <-> TDM400P <-> Fax Machine I have used Zapbarge to listen to the data stream, but I can't say if it really have some time slips - fax kinda noisy in itself. Using the zttool i saw the Sync source for the TDM are

Hi.... Apologies for the length of this, but any help would be greatly appreciated ;-)... I have installed and configured a Digium E100P on my Asterisk PBX and I have connected this to an 8 port E1 VoIP gateway on a Cisco 6509. There is also an external E1 link from our Telco plugged into one of the other ports on this gateway and this gateway is in turn registered with a Cisco CallManager

Hi- Perhaps someone with an E100P in hand can answer this: I just received an E100P from Digium (I normally buy quad boards) I noticed that the circuit board says "T100P" on it, and I assume that the T100P and E100P both use the same circuit board. Can someone please confirm that their E100P says "T100P" on the artwork? Thanks Scott Scott M. Stingel Emerging Voice

I have spent some time this morning trying to add an Astribank to our current Asterisk, but it failed, so I just removed the hardware, restore the config files to the original setup and started asterisk.; I could see that no Zap channels are started so I did load chan_zap.so: pbx*CLI> module load chan_zap.so [Feb 26 10:32:18] WARNING[3809]: pbx.c:2968 ast_register_application: Already have an

Just cross pairs 1-2 and 4-5 1 <--> 4 2 <--> 5 Never done an E1, but I think it's the same for a T1 4 wire cable. Tim Thompson Commercial Sales Engineer http://www.amatechtel.com (806) 722-2227 -----Original Message----- From: bam [mailto:bam@cqm.co.uk] Sent: Monday, December 29, 2003 9:12 AM To: asterisk-users@lists.digium.com Subject: [Asterisk-Users] E100P pinouts

Hello, I have a E100P card from digium and I try to implement a conference bridge in asterisk. I wonder since I got the E100P card do I still need to load ztdummy for caller from h323 endpoints to work with Meetme? I load the E100P driver but i did not load the ztdummy driver. My h323 caller does not hear any voice play by Meetme. Looks like ztdummy is required as long as h323 is concern and

Hi, I had a question regarding asterisk installation with 2 E100P card. I would like to do such installation but I had some troubles: PABX -> E100P -> asterisk -> E100P -> PSTN In fact I would like to add some IP Phones to my PABX wich is full. But with this installation, I can't place call. I can receive call without problems. I also can place call from IP Phone, but I

hi see below's conversation. it seems the e100p card doesn't work with BT. Any idea how this'll work against Telenor (norway)? roy <RoyK> does anyone know if I can trust the E100P to do full PRI stuff in .no? <cypromis> dunno about no <cypromis> I cannot use it in UK <cypromis> cause the framer has problems with system-x switches at bt