similar to: TE410P startup

TE410P card down. I have three (3) TE410P in one machine running asterisk with SS7. My problems started last week when one of my cards started switching to E1 every time after reboot. I set the following in dahdi.conf and that solve the problem. /etc/modprobe.d/ options wct4xxp t1e1override=0x00 Now all 4 ports on that card is down with Red Alarm. I tried rebooting the machine and

hi, I'm trying to configure my newly acquired TE410P card to work as 4 E1 spans. This is supposed to be a drop-in replacement to the earlier E100P card. However, on loading the zaptel module it gets configured as T1 spans basically doing a 'cat' on /proc/zaptel/1 thru 4, it shows 24 channels per span. After this ztcfg fails saying 'ZT_CHANCONFIG failed for channel 97'.

hi all, i am trying to get my TE410P (see previous posts) working in Austria (telekom Austria - i am still waiting for an answer for my questions). my /etc/zaptel.conf looks like -------------------------------- span=1,1,0,ccs,hdb3,crc4,yellow span=2,2,0,ccs,hdb3,crc4,yellow bchan=1-15,17-31 dchan=16 bchan=32-46,48-62 dchan=47 loadzone=at defaultzone=at -------------------------------- after

Hi everybody I've just installed a new Redhat 8.0 and configured it with Asterisk, zaptel and libpri. Afterwards I installed a TE410P and configured this as well. But when starting Asterisk I get the following error message: ------------------------------------------------------- -- Registered channel 1, PRI Signalling signalling ..... -- Registered channel 15, PRI Signalling

Hi- I'm looking for an appropriate system board to power a system with two (2) Digium TE410P cards. Since these cards require the 3.3 volt PCI, I'm considering vendors like Tyan for the motherboard. Can anyone please tell me their experiences with the Tyan i7501 series (Xeon-basd), or recommend an alternate motherboard? Thanks Scott Scott M. Stingel Emerging Voice Technology Inc.

I've just encountered an odd problem with our Digium TE410P card and was wondering if anyone has experienced something similar before. We utilize all 4 ports with 2 of them connected to the PSTN as E1 with the second 2 ports connecting to a device which accepts T1. We are essentially acting as an E1 to T1 converter. This machine has been operational for close to 6 months without a problem.

Hi, Digium's E400P has RJ45 conector and my E1 link has BNC concetor. Could someone tell me the cable pinouts to make this conection? thanks Eduardo

Hello, I am looking to buy a large number of TE410P cards for a big international project. I have studied the documentation and zaptel.conf and as result I have the following questions: 1. How do you switch the card from ISDN PRI TE to NT? This means from being configured as User Equipment (the PABX) to be Network Equipment (the Exchange). 2. How do you configure the card for E1 or T1? 3. In

I'm installing TE405P card. This is my zaptel.conf. -------------------------------------- span=1,0,0,ccs,hdb3,crc4 span=2,1,0,ccs,hdb3,crc4 span=3,0,0,ccs,hdb3,crc4 span=4,0,0,ccs,hdb3,crc4 loadzone = us defaultzone= us -------------------------------------- When i modprobe wct4xxp, -------------------------------------- PCI: Found IRQ 11 for device 02:0b.0 PCI: Sharing IRQ 11 with

Hi to all, I have a problem with this wildcard and one E1 line. The server is a Asus P4P800S with the 865PE chipset, and 512MB RAM. The kernel version is 2.4.26. I have donwload and build the latest CVS version of zaptel, libpri and asterisk following the ufficial instructions of digium. I have set up my server in this way: zaptel.conf loadzone=it defaultzone=it

I am trying to install a TE405P which is to be connected to E1 trunks. I have set the jumpers to E1 (closed), but modprobe wct4xxp still fails with the message: ZT_CHANCONFIG failed for channel 97 - which obviously means the card is still in T1 mode. I have tried everything I can think of, any ideas? TIA

Hi. I'm just trying to install a TE410P card (jumped as E1). But I'm having problems loading the kernel module. [root@asterisk1 src]# modprobe wct4xxp /lib/modules/2.4.21-32.0.1.ELsmp/misc/wct4xxp.o: init_module: No such device Hint: insmod errors can be caused by incorrect module parameters, including invalid IO or IRQ parameters. You may find more information in syslog or the

Hi list, We have been trying to configure a Quad Span T1 card in a system running RH9. We have followed the instructions in the Wiki and searched the mailing lists, but so far havent got any success. Cable is connected to the first span, and module is loaded. Without loading the module the LED glows in red colour, but the moment we load module, it goes off. (No red or green) . We ran zttool

Hi all, I replaced a TE410P Rev C 1st Generation Firmware with a TE411P without any cfg changes (zaptel/zapata). As a result Asterisk crashes on outbound from PRI4 going to PRI1 calls: Aug 23 18:22:00 WARNING[4693]: chan_zap.c:7545 zt_pri_error: PRI: !! Got a UA, but i'm in state 1 Aug 23 18:22:00 WARNING[4693]: chan_zap.c:7545 zt_pri_error: PRI: !! Got a UA, but i'm in state 1

Greetings, According to the FAQ "When you load the module and have no circuit/channel bank the LED's should flash red" I get the "knight rider" lights before the module loads, but after the modules are loaded I don't get any lights, other equipment plugged in or not. The card has been on my shelf a while so I wonder if it needs a firmware upgrade ? Can the cards

Is anybody else using the following combination: * a TE410P card (wct4xxp driver) * a BT ISDN connection * DAHDI 2.3.0.1 * Asterisk 1.6.2.9 I'm trying to configure a new box to replace a legacy system (same hardware; some old version of Asterisk with Zaptel; works lovely but hopelessly out-of-date) and not having much joy. Specifically, I couldn't get it to see a D-channel on

Hello All I am looking for the cable I need to create to connect a TE121 card with a TN2464BP card (AVAYA ISDN Card), please let me know if someone have the information about this cable, my asterisk CLI show this: pri show span 1 Status: In Alarm, Down, Active And the card is in red, so I am thinking the problem is the card. Any idea??? Thanks John Teleperformance values:

hi all, i've now installed a TE410P (Quad T1/E1 Primary Card - Digium) and connected it to a primary line. My telco (eTel) only told me that they are using hdb3 and crc4. So i still don't know which coding i have to use (cas or ccs) - and what timing options i have to use. Have someone already get a card like this up in Austria with a line from eTel or from the telekom Austria ? Another

Hello I've got small PBX (30 simultaneous connections) based on asterisk (1.6.2.6), which uses Stargate 2N ISDN to GSM gate. It runs ok for day or two, but then I get: dahdi: HDLC Receiver overrun on channel TE4/0/1/16 (master=TE4/0/1/16) in my kernel logs, in asterisk i get: pri show spans PRI span 1/0: Provisioned, Down, Active PRI span 3/0: Provisioned, In Alarm, Down, Active (span 3

Hello, I have a Digium TE410P card. I get the "knight rider" lights before the module (wct4xxp) loads, but after the modules are loaded I don't get any lights. I have found the following 2 posts but still could not solve the problem http://lists.digium.com/pipermail/asterisk-users/2004-November/075277.html http://www.voip-info.org/tiki-index.php?page=Asterisk+TE410p+No+Interrupts