Displaying 20 results from an estimated 5000 matches similar to: "channel bank setup "What do I do now?""
2003 Jun 08
2
zapata.conf and zaptel.conf
Can anyone explain to me the difference in zaptel.conf and zapata.conf?
I'm trying to get a real clear understanding of them but its getting a
little murky in places. I will be setting up a PBX running asterisk with
2 T100P cards. I will be bringing a 23 channel PRI into one card and
connecting the other card to a Nortell 24 channel FXS channel bank. As I
understand it zapata.conf is
2004 Jul 02
0
Channel Bank Newbie Problem
Hi all
I'm trying to configure a TE410P in Europe with three
E1s and a T1 channel bank (already bought in the US) to receive and make
calls through *. I managed to get the E1s to work, but I'm having
trouble with the channel bank (a Rhino). I have tried the bank in spans
1 and 4 changing jumpers in the card (always with no PRI connected, as I
have no PRI where I'm testing now,
2004 Jan 17
1
Channel Bank Woes...
Hello all,
I have a new Carrier Access Adit 600 and am having a problem dialing out
and receiving incoming calls.
After the initial ring, the calling party will here nothing. There is a
silence, but the SIP phones that is supposed to ring will ring. The
calling party will not hear the sound of the ring that * sends out on
the line. Additionally, if someone picks up the receiver there is no
2003 Oct 14
2
T100P to Adtran TA750 - No dialtone or ring
Hello all,
I've got a T100P connected to an Adtran TA750 with a T1 crossover...
This connects to a patch panel with phone ports. The Adtran is fully
populated with FXS cards.
All I get on any phone port is a fast clicking noise... No dialtone.
Asterisk 'sees' the card, (the channels show up in /proc/zaptel).
Incoming calls are routed to the zap/x channel, but no ring.
I'm
2008 Jul 25
0
Slightly Off Topic: Cisco & Premisys Slimline
Has anyone got a Premisys Slimline channel bank working with a Cisco
AS5400 or similar?
I'm not sure if my unit is bad, or what. I'm using FXS Loop Start.
Calling the port connects immediately without ringing the attached
phone. If I pick up the phone, it's connected and I can talk to the
caller. Hanging up has no effect. I can see the bit transitions (0101
to 1111 when I go
2005 Aug 10
2
ZAP bchan and dchan HELP!!
We have install a DS3 with 28 DS1's we have an Adtran MUX breaking out
the DS1's, we are trying to setup the system with 2 dchannels for each 4
DS1's.
Everything looks fine when modprobe zaptel and wct4xxp and ztcfg -vvvvvv
but when I asterisk asterisk it says:
Aug 10 16:33:32 ERROR[8954]: chan_zap.c:6750 mkintf: Channel 24 is
reserved for D-channel.
Aug 10 16:33:32 ERROR[8954]:
2011 Jan 05
0
TE420 issue: card 0 span N: isr2=XX isr3=Y
I have just built a new system using an HP DL360G7 with a TE420 T1 card,
and this is the first system using a generation 7 server. I'm not sure
whether that is an issue or not.
I am using Asterisk 1.2, and Zaptel 1.4.12.1 with patches for GEN5 of
the TE420 card. I have successfully used this combination on several
systems based on the DL360G6 and TE420(gen5), which have been in
production for
2006 Jun 06
1
Asterisk exit on startup
I'm having a problem with a new installation of asterisk 1.2.5 with a
digium dual port T1 (span 1 connected to an outside line, and span 2
connected to a CAC access bank I channel bank with 24 fxs ports). When I
start Asterisk (either from safe_asterisk or asterisk -vvvc) it will
immediately exit after it initializes. It will start the logger,
register applications and functions, register
2003 Nov 20
4
T1 / Channel Bank Configuration
I know this topic has been covered before - I just want to make sure I
am understanding this correctly.
| -------------------
| | |
| T1 | Channel Bank |
| ----------| |
| | T1 Cross | |
| | | |
| | -------------------
--------------
| Asterisk |
| |
|
2005 Oct 09
2
Clicks, pops and noise
Hi all,
I've got a TE410p connected via T1 to four channel banks (2 FXO and 2 FXS), no PRIs.
Some users are complaining that they hear clicks and pops on the FXS lines,
generally when they pick up the phone it's noisy. This happens only after a
while, e.g. after a fresh restart of everything, all is fine but after some time
these noises start appearing. From what I've read on the
2013 Jan 06
2
PRI (Primary-NTT)
hi folks.
i recently setup an Asterisk system in Hong Kong. their phone
company told me that their T1 PRI switch type is Primary-NTT.
however in chan_dahdi.conf there's no such option. i have it
set to national. it worked fine for a while, but now suddenly
stop working. in coming call just keep ringing and didn't
even show up on console. out going call hang up immediately
with cause code
2004 Dec 22
0
TE410P to a Rhino CB-24 channel bank
Has anyone had any success with the Rhino CB-24? I can't get mine to
work, I tried all the obvious settings. The cb-24 gets stuck at init ESF
framing, as if it's not seeing the t1 card at all. It does get a t1
carrier (detecting voltage??)
Help!
Thanks..
Everything appears to look good on the server, I did:
[zaptel.conf]
span=1,0,0,esf,b8zs
fxogs=1-24
[zapata.conf]
signalling=fxo_gs
2005 Aug 02
2
Channel Bank Help Please....
Hello -
I have a Premisys Slimline Channel Bank connected to a Digium TE110P. I
am not able to call the FXS extensions or get dialtone on them. The
channel bank is connected via a T1 crossover to the cable and lights
show green. I really need to get this functioning by end of day. If
anyone can help me out I would be greatly appreciative.
Thanks,
Dave
zaptel.conf
loadzone =
2003 Apr 30
5
PRI Setup
Heh guys, I just received a T400 card, I've been using a T100 for a
little while, and it works fine when using a raw channelized T1. I'm
relocating my asterisk machine, and PRI's will only be available,
haven't found any good config info for PRI's, can someone point me to
PRI config info, or let me know what changes I need to make in order to
bring them up, I imagine,
2005 Jan 04
0
Question on behalf of a wannabe new list member
---------- Forwarded message ----------
Date: Tue, 4 Jan 2005 17:12:32 -0800
From: Bill D'Anjou <danjou@rocketinternet.net>
To: steve@daviesfam.org
Subject: FW: [Asterisk-Users] TE410P card in an HP-Compaq DL380 G4 server
Can you post this to the group for me? I've joined & I am receiving
e-mails from the group but when I try to post I get a bounce saying
"waiting for
2005 Jul 22
0
all zap channels get RING signal when starting *
hi all,
when i start * all zap channels get ring signal so i get a huge number
of incoming dummy calls when starting *. i'm using TE105P with 4 TA750
full fxo with latest CVS HEAD:
zaptel.conf:
span=1,0,0,esf,b8zs
fxsks=1-24
span=2,0,0,esf,b8zs
fxsks=25-48
span=3,0,0,esf,b8zs
fxsks=49-72
span=4,0,0,esf,b8zs
fxsks=73-96
loadzone=us
defaultzone=us
zapata.conf:
[channels]
context=incoming
2006 Feb 27
0
TE411P problem-- probably stupid.
Hi,
Probably a stupid syntax problem.. but can't seem to make
these files work for more than the first T1 (ok, if I comment out
the 2nd, 3rd, and 4th span).
Can someone proofread this for me?
Thanks!
======================
zaptel.conf
span=1,0,0,esf,b8zs
bchan=1-23
dchan=24
span=2,0,0,esf,b8zs
bchan=25-47
dchan=48
span=3,0,0,esf,b8zs
bchan=49-71
dchan=72
span=4,0,0,esf,b8zs
bchan=73-95
2007 Jan 03
0
Sangoma A102 w/ EC module gets intermittent echo/audio artifacts
I think you are absolutely right. The audio I heard earlier sounds exactly
like a timing issue. So:
wanpipe1.conf:
TE_CLOCK = NORMAL
TE_REF_CLOCK = 0
wanpipe2.conf:
TE_CLOCK = MASTER
TE_REF_CLOCK = 1
zaptel.conf:
span=1,1,0,esf,b8zs
span=2,0,0,esf,b8zs
I'm going to make this change and reload at lunchtime, I'll document it and
post it to the list if it works.
2007 Jan 04
0
Sangoma A102 w/ EC module gets intermittent echo/audio artifacts <--followup and resolution
Followup on this issue, it appears that using a single PRI's clock as the
master clock avoids clock drift between the PRI's and we get no more
artifacts. So, :
wanpipe1.conf:
TE_CLOCK = NORMAL
TE_REF_CLOCK = 0
wanpipe2.conf:
TE_CLOCK = MASTER
TE_REF_CLOCK = 1
zaptel.conf:
span=1,1,0,esf,b8zs
span=2,0,0,esf,b8zs
-----Original Message-----
From: Michael L. Young
2005 Sep 28
1
Sep 28 00:42:35 ERROR[5151] chan_zap.c: Unknown signalling method 'pri_net'
Any ideas?
51] logger.c: [chan_zap.so] => (Zapata Telephony)
Sep 28 00:42:35 VERBOSE[5151] logger.c: == Parsing '/etc/asterisk/zapata.conf': Sep 28 00:42:35 VERBOSE[5151] logger.c: == Parsing '/etc/asterisk/zapata.conf': Found
Sep 28 00:42:35 VERBOSE[5151] logger.c: == Parsing '/etc/asterisk/zapata-auto.conf': Sep 28 00:42:35 VERBOSE[5151] logger.c: == Parsing