similar to: Channel Bank configuration

I am having trouble getting my T100P and ADIT 600 talking. I have 2 FXO 8 port cards in the ADIT and a T1 controller card. I have a T1 x-over cable connecting two together. Here are copies of the relevant bits of my zaptel.conf and Zapata.conf Zaptel.conf span=1,0,0,esf,b8zs loadzone=us defaultzone=us Zapata.cfg context=default signalling=fxs_ks group=1 channel => 1-24 My

Hello, I am connecting Asterisk to an Adit 600 via a T100P. Unfortunately I am not able to get any lights on the T100P and the Adit 600 only shows red. I have already modprobed the t100p. Has anyone successfully connected these before? I've tried both a cross-over cable and a standard cat 5 cable, but I can't seem to get them to work. Any suggestions? Thanks! Craig

Hi, I was using samba 2.0.7 veersion for a while without any problem. This morning, suddenly, many windows (nt/98) cannot connect the samba server on our Linux (RedHat 6.2) server. Then, I downloaded the version 2.2.4, extracted, configure it, make, make install according to the document. Then I test it by running ./testparm it lists all of shared folders. Then, I run ./smbclient -L

Hello, I will be setting up two asterisk systems and I'm looking for some suggestions as to what the best way to do this will be. The 2 systems are for 2 companies that share a single T1 line. The T1 line has 12 voice channels and 12 data channels. Currently, they are set-up as follows: T1 line from provider enters CSU/DSU and splits voice/data channels. The voice channels are sent to

Folks, I'm experimenting with bringing multiple (8) analog lines from our local telco into a Carrier Access ADIT 600 channel bank with an FXO module, then having this talk to Asterisk via the T1 TDM controller on the ADIT and a TE405P card. I don't know if this will work well (ie: give me decent echo cancellation, call disconnect supervision, caller ID etc) but I haven't had much

Hello, I've recently purchased Adit 600 with 3FXS and 1FXO to be connected to my * server via T100P card. This is the output of "status equipment" command in the Adit600: For some reason the FXO card is seen as FXS, why? Is it ok? On the card it is written "FXO". Regards, Shlomi Bachar -------------- next part -------------- An HTML attachment was

Has anyone had any success using the Adit 600 with the CMG card talking MGCP to asterisk? I want to have a central asterisk server with 10 Adit 600's at various locations providing 24 FXS ports.... Thanks, Isaac

I am hoping to replace my Nortel 8x24 switch with Asterisk. Right now my cabling comes from my outside phone box into my office and into a punchdown block and leaves the punchdown block as an amphenol connector which currently plugs into the Nortel swicth. A second amphenol connector them plugs into the switch and extends to another punchdown block that I believe carries the lines throughout the

I'm having issues with echo. My setup is Polycom IP501 phones connected to an Adit 600 via T100P. 13 Lines going to the Adit. All echo so far is on the local side (Employees hears own voice, but only on some calls). Watching the channel with ztmonitor, I notice that TXGAIN is pegged out most of the time. RXGAIN is anywhere between 45 and 60%. Is it safe to assume that playing around

I know a few ppl have those CAC Adit 600's with t400 I can't seem to get my second span up on the T400 connected to the second spand on the adit (A:2) A:1 seems ok Can someone post they zaptel.conf span defintions And maybe a "print config" from the adit 600 cli I think my issue is timing srcs the coding, framing. bld out are all matched thx -------------- next part

Hello All, I could use a recommendation if anyone has a moment. I have the T100P but I have not gotten my service yet. I want to have at least 12 lines of digital voice with DID. Should I just seek out a PRI ISDN provider or is there something else I should look for? I want to keep cost as low as possible. Also, I want to own my own router for the phones since it is always a hassle to get

I've searched but can't find an answer as to how many MGCP paths can a single ADIT/CMG card support? It appears it's only 24 ports, maybe 48. What I'd like to do is install 6 Telco T1's into a single (or more) Adit 600 and route inbound calls towards asterisk. Can I have more than one CMG in a single chassis? Or maybe you know of a better way to connect T1's to

I work for a school dist, and I am having a bit of trouble with the "Student Server" We have about 3000 students all with their own accounts. I had the samba server setup to share their home directories but their home directories are the same as their login name. So jamie.mcparland would be an example of a share name. But in Win 9X it gets truncated to jamie.mcparla then we get the error

I'm looking to buy a channel bank. I'll be using this to basically dual a Toshiba PBX and Asterisk so that we can deploy Asterisk in small steps and have the Toshiba as a fallback in case something goes wrong. What I need is a channel bank that will allow me to take in 12 lines using the FXO ports in the CB and then output those lines to the Digium T100P. Has anyone had experience

Wondered if anybody might have some ideas about what could be causing this.... I have a T100p hooked up to an Adit 600 with 12 channels of voice off of a T-1 coming in. I have a t100p connected to a zhone z-plex with 24 fxs going to my stations. Some of the station are 2 line phones. These have 2 zap channels that are dialed when the extension is matched. Also, some extension require ringing 2

Here's our config: cisco 7960's running 6.3 sip code latest cvs of * t100p zaptel card adit 600 channel bank 7 pots lines and 2 fax machines on the adit 600 dialing out from the cisco phones gets sent out via the zap channels, but I'm having some serious echo problems. I currently have the adit set to +3 rxgain and -6 txgain, with my zapata.conf containing: echocancel=128

Say I get an ADIT 600 with two FXS8A and one FXO8A from ebay. a. Is it good for Asterisk? b. How do I connect the extensions and lines to it? Do I need a special jack? Can I get that jack in every corner? c. where can I find help for configuring it? d. what kind of backup does it have? Does it need to be reconfigured after a power outage? Shoval Tomer, IT Manager, SofTov Advanced Systems, Ltd.

I've been reading the Google searches trying to understand how to tie together Adit 600 to Asterisk to provide 2 way service. I'm about blind from reading. I assume, the answer is using MGCP between the boxes. However, the examples I found don't really explain fully enough to know how to modify examples to work for me. I'll have in the ADIT with T1's. There is a CMG and

I'm going to install asterisk with four digium cards. Can anyone mention a brand that carries boards with 4 compatible pci slots? Thanks Shoval Tomer, IT Manager, SofTov Advanced Systems, Ltd. Office: +972-3-9230686 ext. 179 Fax: +972-3-9216642 Mobile: +972-54-8000200

Hello, I have an Adit 600 (3 FXS cards) hooked up to a digium T1 card in my asterisk box. I 'connected' the slots to the a:1 T1 interfaces via the command line. The slots (3 fxs) are configured with 'ls' signaling. I configured the T1 card with the same line settings as the T1 interfaces on the adit and I get green lights on both the T1 card and the T1 interface on the adit (so