similar to: Help! Problems talking to upstream switch

Hello, I don't have any experience with channel banks and would appreciate any feedback on my theory outlined below: We have a single T1 entering the building with channels 1-12 being voice lines and 13-24 being a 768k internet connection. This T1 terminates to an Adit 600 (T1-1). Here's what I know. Channels 11-12 go out the Adit 600's 25-pair connector to a wiring block (and

This probably has an easy solution, but I found it yet. How can I get out of a remote console after using ssh to get into the box, making changes, reload etc. without stopping *? Thanks in advance. Sincerely, Andy Hester Consero

Ok, the Zhone sucks and the Adtran 750/850 seems to be a little too expensive. Can anyone recommend a decent channelbank that won't break the bank? TIA, -- Troy Settle Pulaski Networks http://www.psknet.com 540.994.4254 ~ 866.477.5638 Pulaski Chamber 2002 Small Business Of The Year

Wondered if anybody might have some ideas about what could be causing this.... I have a T100p hooked up to an Adit 600 with 12 channels of voice off of a T-1 coming in. I have a t100p connected to a zhone z-plex with 24 fxs going to my stations. Some of the station are 2 line phones. These have 2 zap channels that are dialed when the extension is matched. Also, some extension require ringing 2

Hi, Have posted to this list a couple of times and have always received great responses and help. I have a basic * system setup Using 3 X100P cards with 6 Snom200 IP phones. It was a bit of a struggle getting everything up and running but have been pretty happy with the flexibility and ease of *. My major problem is one that has been discussed on this list many times before. The echo

Can anyone recommend some phone sets that are adsi compliant and work well with asterisk?

Hello, I am connecting Asterisk to an Adit 600 via a T100P. Unfortunately I am not able to get any lights on the T100P and the Adit 600 only shows red. I have already modprobed the t100p. Has anyone successfully connected these before? I've tried both a cross-over cable and a standard cat 5 cable, but I can't seem to get them to work. Any suggestions? Thanks! Craig

Hi, I have scanned through the archives of this list and found a number of question about hardware, but I just can not find the answer to my question. I am new to phone systems, I got "drafted" to come up with a new phone system for our company (I guess they figure since I know computers I know phone systems as well :O). We have 5 analog (I guess they are called PSTN lines) lines coming

I know a few ppl have those CAC Adit 600's with t400 I can't seem to get my second span up on the T400 connected to the second spand on the adit (A:2) A:1 seems ok Can someone post they zaptel.conf span defintions And maybe a "print config" from the adit 600 cli I think my issue is timing srcs the coding, framing. bld out are all matched thx -------------- next part

I'm going to install asterisk with four digium cards. Can anyone mention a brand that carries boards with 4 compatible pci slots? Thanks Shoval Tomer, IT Manager, SofTov Advanced Systems, Ltd. Office: +972-3-9230686 ext. 179 Fax: +972-3-9216642 Mobile: +972-54-8000200

The benefits of * are obvious so that part of the marketing an * solution is easy. Anybody care to share ideas on how to target companies who would benefit most from */Digium? It seems to me that it would be an easy sell to small/medium companies who need advanced features such as ip trunking, IVR, Conference bridging, etc., etc. I would like to find a way to identify multi-location companies

I am having trouble getting my T100P and ADIT 600 talking. I have 2 FXO 8 port cards in the ADIT and a T1 controller card. I have a T1 x-over cable connecting two together. Here are copies of the relevant bits of my zaptel.conf and Zapata.conf Zaptel.conf span=1,0,0,esf,b8zs loadzone=us defaultzone=us Zapata.cfg context=default signalling=fxs_ks group=1 channel => 1-24 My

I just picked up a couple CAC Access Bank 1s loaded with FXS that should be arriving shortly. Does anyone have one that they use with Asterisk? If so, would you be willing to shoot me a note with your current configs? I'm not very familiar with CAC/etc, and it would save me countless hours of muddling through .. :) Any others tips you can give me on these banks would be very

Folks, I'm experimenting with bringing multiple (8) analog lines from our local telco into a Carrier Access ADIT 600 channel bank with an FXO module, then having this talk to Asterisk via the T1 TDM controller on the ADIT and a TE405P card. I don't know if this will work well (ie: give me decent echo cancellation, call disconnect supervision, caller ID etc) but I haven't had much

Hello All, I could use a recommendation if anyone has a moment. I have the T100P but I have not gotten my service yet. I want to have at least 12 lines of digital voice with DID. Should I just seek out a PRI ISDN provider or is there something else I should look for? I want to keep cost as low as possible. Also, I want to own my own router for the phones since it is always a hassle to get

I need a good reliable source for channel banks. Ebay is nice but too many variations of quality. I need one that can do 8 FXO and 16 FxS does anyone have a particular model, other than adtran that they can recommend??? And if possible include a source to buy from... Thanks in advance, Alex -------------- next part -------------- An HTML attachment was scrubbed... URL:

Say I get an ADIT 600 with two FXS8A and one FXO8A from ebay. a. Is it good for Asterisk? b. How do I connect the extensions and lines to it? Do I need a special jack? Can I get that jack in every corner? c. where can I find help for configuring it? d. what kind of backup does it have? Does it need to be reconfigured after a power outage? Shoval Tomer, IT Manager, SofTov Advanced Systems, Ltd.

Hello, I'm about to install asterisk as the PBX at a location that my company has just moved into and I would like to get some comments and advice on the installation. I am new to * and don't want to make any big mistakes so I would love to hear whatever anyone has to say. Here is what I have so far Server: * 2.8Ghz P4 - 1G ram * T400P Tormenta II (is this as good as the

Hello, I've recently purchased Adit 600 with 3FXS and 1FXO to be connected to my * server via T100P card. This is the output of "status equipment" command in the Adit600: For some reason the FXO card is seen as FXS, why? Is it ok? On the card it is written "FXO". Regards, Shlomi Bachar -------------- next part -------------- An HTML attachment was

Hello, I am working for a charity in the UK and I am projecting a new phone system. We would like to connect our two-wire telephones (40 or so) to an ADIT 600 channel bank, and connect that into an Asterisk box via the CMG card or T1 card. I have been in talks with Carrier Access about the purchase of a new channel bank and we tried to get a minor version of it first for testing with the