similar to: Tiger Jet card X100P

PC: HP Vetra VL400 Mainbood: Intel815 BIOS: Phonix 4.0 release 6.0 OS: REDHAT 9.0 I installed the X100P in PCI slot 2 and disable the USB port, serial-port and parallel-port in BIOS. I can't found the X100P card in " cat interrupts" But I can found the card in the "cat ioports" use "lspci" I found the X100Pcard use the interrupts 11 too. Who can help me to solve

Hi all! I'm new with telephony cards and DAHDI drivers. I have installed Asterisk NOW 3.0.0 and update to Asterisk 11.7.0, modules are update too. I'm following the installation guide of Atcom [1] for AX1600P analogic card, modules are loaded [root at pbx ~]# lsmod | grep -E "hisax|netjet|dahdi" netjet 14618 0 isdnhdlc 4523 1 netjet mISDNipac

Hi, I using asterisk 1.2.4 on a CentOS with Linux 2.6.9-22.0.2.ELsmp kernel. I've two x100p cards connected, only one card is reconigzed by asterisk. 02:01.0 Communication controller: Tiger Jet Network Inc. Tiger3XX Modem/ISDN interface 02:02.0 Ethernet controller: Davicom Semiconductor, Inc. 21x4x DEC-Tulip compatible 10/100 Ethernet (rev 31) 02:03.0 Communication controller: Tiger Jet

Hi, I have a TDM400P running with only one FXO port running on a VIA EPIA MS10000 (1Ghz Via Eden). When I run zttest from Zaptel 1.2.1 it hang and when I interrupt it with Ctrl-C that is the result: ?anyone have some idea about why isn't working? Some additional info: # /usr/src/zaptel/zttest -v Opened pseudo zap interface, measuring accuracy... --- Results after 0 passes --- Best:

So I took a chance with an X100P knock-off on eBay. I'm running Asterisk + FreePBX on a PowerMac G3 (beige desktop) using Slackintosh 10.2 and kernel 2.6.16.16. Everything has been fine up until now. I compile the 1.2.5 Zaptel drivers without a problem, get the udev configuration in, modprobe zaptel, and finally modprobe wcfxo. At this point, I get the message: ZT_CHANCONFIG failed on channel

Hi, I've got asterisk working as a PSTN gateway between two sites. The IP connection is pretty good and bandwidth exceeds 640Kbps all the time. I'm using X100P hardware on 300Mhz and 333MHz systems. One of them has a sound card, but the slower system does not have a sound card. Both are connected to PBXes and I have busydetect=yes on one end because the PBX doesn't drop the

Hi All, I hope I'm posting this to the appriopriate list, and that cross posting to two lists is OK. (If not, I'm sure I'll hear about it quickly :)) I'm running Asterisk on my (new) VIA EPIA-V motherboard. This seems to be the ideal platform for a home version of asterisk - its small, quiet, low power, and should have plenty of computing horsepower if only it would work!

Hello list, After upgrading from BRIstuff 1y-b to 1y-e my ISDN card is suddently detected as 2 ports instead of 4. I still load the driver as "modprobe qozap ports=12" as I've always done. But now it only sees 2 ports. Output of "lspci -vvv" ------ cut -------- 02:01.0 ISDN controller: Cologne Chip Designs GmbH ISDN network Controller [HFC-4S] (rev 01) Subsystem:

Hi, I'm trying to passthrough legacy PCI ISDN controller to a KVM based virtual machine: <hostdev mode='subsystem' type='pci' managed='yes'> <source> <address domain='0x0000' bus='0x04' slot='0x00' function='0x0'/> </source> <address type='pci' domain='0x0000' bus='0x00'

Hello list, I'm having a problem with a BRI card, a B200E (PCI-e) card on an Intel server with a riser that I'm guessing is what's making the problem. The output of lspci -vvv is: 07:00.0 ISDN controller: Cologne Chip Designs GmbH ISDN network Controller [HFC-4S] (rev 01) Subsystem: Cologne Chip Designs GmbH Device e884 Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop-

Hello, I am having problems, getting my asterisk-domU to work properly. It consists of the following components: - Debian Etch under Xen-3.1 with a 2.6.18-kernel - Asterisk 1.2.24 - mISDN-1.1.5 I have 2 HFC-ISDN-cards, which I pass through to the Asterisk-DomU in permissive mode. This is working fine. The strange problem is, that the two HFC-ISDN-cards are not beeing initialized by the

Hi List, I'm setting up a system with one TDM400P (2*FXO + 2 * FXS) and one Junghanns QuadBRI on a Fedora Core 6 (Kernel 2.6.20-1.2944.fc6). I'm using the bristuff-0.3.0-PRE-1y-e kit. It download zaptel-1.2.16, libpri-1.2.4 and asterisk-1.2.17 When it's the time for ztcfg to do its job it complains with <ZT_SPANCONFIG failed on span 2: No such device or address (6)>

Hi everyone. We have a problem here... Hope somebody can give us some hints. We have a HP ProLiant DL180 G6 Server with a Debian/Lenny sytem. Asterisk 1.4.21.2 (1.4.21.2~dfsg-3+lenny1) with zaptel (1.4.11) and libpri (1.4.3) is installed. There is a QuadBRI-Card installed: # lspci -vv -s 06:04.0 06:04.0 ISDN controller: Cologne Chip Designs GmbH ISDN network Controller [HFC-4S] (rev 01)

Hi, The following error message appeared in syslog while the filesharing client overnet was running and writing to the disk. I first only noticed that suddenly Opera was frozen and no new terminals could be started. Regards W. Pichler syslog Jun 15 13:15:34 pc kernel: Unable to handle kernel NULL pointer dereference at virtual address 0000000e Jun 15 13:15:34 pc kernel: printing eip: Jun

Ack! This slipped through my email. I am terribly sorry. Thank you so much for responding. On 04/06/2014 08:43 PM, Ilia Mirkin wrote: > On Sun, Apr 6, 2014 at 7:16 PM, ~Stack~ <i.am.stack at gmail.com> wrote: >> Greetings, [snip] >> My working kernel is: 2.6.32-358.23.2.el6.x86_64 (and anything before). >> >> The problem kernel is: 2.6.32-431.1.2.el6.x86_64 and

Hi! I tried to pcipassthrough usb-controllers to domu to use it with a memory-stick. First xen complained that the driver needs write-access to its configuration space, so I added these to pci-quirks. Since it still didn''t work I also added the device to pci-permissive but I still get an errormessage with Oops (at the end of this email) when sticking in the memory-stick. I tried

Hi! I tried to pcipassthrough usb-controllers to domu to use it with a memory-stick. First xen complained that the driver needs write-access to its configuration space, so I added these to pci-quirks. Since it still didn''t work I also added the device to pci-permissive but I still get an errormessage with Oops (at the end of this email) when sticking in the memory-stick. I tried

Hi all, I've seen a couple of posts recently from people who are doing something with Asterisk and a T100P and a Nortel PBX. However it's not clear exactly what they are doing. Does anyone know if it's possible to use a T100P or T400P as a DSX-1 interface to connect to a T1/PRI CO module in a Nortel PBX? We have a Nortel Norstar Modular ICS PBX and I'd like to plug its CO

Hi all, For some reason VSAT or Satellite Internet services are not mentioned (or searchable) in this list's archives. I thought I'd let you know that I tested Asterisk using IAX (not IAX2) to make a phone call from an analog phone hooked up to an Asterisk system behind a Linksys router connected to a Gilat VSAT satmodem, and it worked. The "other end" (gateway) is a

-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 Hi list, I have a *very* strange problem, unfortunately it's kind of a show stopper regarding the deployment of the machine. :( I have two Intel Gigabit Ethernet NICs on board (Supermicro-based Server), quoting lspci (full output see at the end of the email): 0d:00.0 Ethernet controller: Intel Corporation 82573E Gigabit Ethernet Controller