search for: tripp_lit

...metimes depends on the hardware on the host side - for 3016, pre-USB3 controllers had better luck than USB3 controllers, even on non-superspeed ports). David mentioned your model is likely protocol 4004. Here are other compatibility reports with that protocol ID: * https://networkupstools.org/ddl/Tripp_Lite/SU1000RTXL2UA.html * https://networkupstools.org/ddl/Tripp_Lite/SU1500RTXL2UA.html * https://networkupstools.org/ddl/Tripp_Lite/SU1500RTXLCD2U.html * https://networkupstools.org/ddl/Tripp_Lite/SU1000XLA.html * https://networkupstools.org/ddl/Tripp_Lite/SU2200XLA.html Seems like a good choice to m...

We're looking at replacing some old APC SmartUPS 5000s with something that has USB so NUT can more easily talk with it (and yes, I've tried USB-RS232 adapters and every one I tried started kicking out errors within a few hours). One of the bids we have is for a "Tripp Lite UPS Smart Online 5000VA 4500W Rackmount 5kVA 200V/240V" as the potential replacement unit. I have no

...down". There is a big clunk noise and the UPS immediately turns off its outlets...and after a few seconds there is a clunk and the ups outlets are back on. I don't understand why the UPS is not staying off when issuing the command /etc/killpower or via sudo upsdrvctl shutdown. ups.conf: [Tripp_Lite] driver = usbhid-ups port = auto pollinterval = 10 desc = "Tripp-Lite SMART1500LCD" vendorid = 09ae ignorelb override.battery.charge.low = 10 ---------------------------------------------------------------------------- nut.conf MODE=standalone -----------------------------------------...

...esults (mostly upsc output, rather than full end-to-end) from connecting many of their their USB UPS models to NUT from one of their sales offices. Interestingly, the following models have the same USB product ID as your UPS, and the Smart1000LCD was on that list: * http://networkupstools.org/ddl/Tripp_Lite/AVR900U.html * http://networkupstools.org/ddl/Tripp_Lite/G1010USB.html * http://networkupstools.org/ddl/Tripp_Lite/SMART1000LCD.html > _______________________________________________ > Nut-upsuser mailing list > Nut-upsuser at lists.alioth.debian.org > http://lists.alioth.debian.org...

...ROBLEM: NUT is ABLE to see the UPS BUT it is not getting the right(?) descriptor? I am using the usbhid-ups driver set. I have tried others, tripplite, tripplite_usb, and blazer_usb and none works. This is the closest I can see it being ?working? According to http://www.networkupstools.org/ddl/Tripp_Lite/SMART1300LCDT.html. It was ?verified? working with NUT version 2.6.4 If any additional information is required please let me know. I like to get this resolved. LOGS & OUTPUTS /usr/local/libexec/nut/upsdrvctl start Network UPS Tools - UPS driver controller 2.7.3 Network UPS Tools - Gener...

...en how many of the model names are reused for very different hardware, it can be helpful to see at least the first few digits of a serial number, but in this case, I don't think we have too many other reports of this hardware to go on. The closest ones seem to be: http://networkupstools.org/ddl/Tripp_Lite/SMART2200RMXL2U.html > If I understand the NUT process correctly, it looks for this LB status in order to create the POWERDOWNFLAG. "In upsmon.conf, add a POWERDOWNFLAG directive with a filename. upsmon will create this file when the UPS needs to be powered off during a power failure whe...

Hello, https://networkupstools.org/ddl/Tripp_Lite/AVR750U.html Going off of this page, it looks like this should be supported by usbhid-ups, but it seems to be failing. Attached is a log of my attempts to start the driver. Let me know what I can do to help. -------------- next part -------------- An HTML attachment was scrubbed... URL: <http:...

I have a TrippLite AVR550U that my company uses several individual Linux boxes in one large system, all running Ubuntu 18.04LTS, and all will be using the package version of nut - 2.7.4. In my scenario, our usage case is for the PCs to all shut down, followed by the individual UPSes, when mains power is removed from the whole system. (This isn't a typical setup for UPS, but it's what

...descriptor? I am using the usbhid-ups driver set. I have tried others, tripplite, tripplite_usb, and blazer_usb and none works. This is the closest I can see it being ?working? For that USB ID (09AE/3016), usbhid-ups is the correct driver. > According to http://www.networkupstools.org/ddl/Tripp_Lite/SMART1300LCDT.html. It was ?verified? working with NUT version 2.6.4 In a message on nut-upsdev, Marco Walther just cited this thread: http://thread.gmane.org/gmane.comp.monitoring.nut.devel/6482 which mentions that the UPS works on Debian Linux 7.1. Marco's patch is against NUT 2.7.3, and...

Hi all, My apologies if this has been asked, but is there anyone who would be willing to help me figure out what to 'edit' in what and which (all?) '.conf' files in /etc/nut to be able to use my new Tripp Lite Smart1300LCD please? I have/need just the most basic setup. It's only me using my computer and only this one computer and a few peripherals being used on the

...1:1 mapping of HID Usage IDs to NUT variables). That might not happen until the weekend. For completeness, would you mind sending the output of "upsrw" and "upscmd -l"? I would like to verify some of the other mappings, and also publish that here: http://networkupstools.org/ddl/Tripp_Lite/index.html

...hark+USBCap on Windows to trace what's going to the TrippLite when this setting is changed -- I've just had very little luck with WS/USBCap in the past, just too much information to sort through. Does the output from "upsc" look similar to this? http://new.networkupstools.org/ddl/Tripp_Lite/AVR750U.html I don't think we have a listing of valid NUT instant commands for the model mentioned in that variable dump (or the AVR550U, for that matter), but both variables and commands could help debug this problem. https://networkupstools.org/stable-hcl.html#footnotes If the delay settin...

At the company I work for, we are using many TrippLite OMNI900LCD UPSs and are having difficulty setting the lower transfer threshold voltage. On our other model, the Eaton MGE-3S550, this can be set using upsrw to set the input.transfer.lowsetting, but on the Omni900, this option is not available. In our testing, it defaults to ~95v but we want to set it to 84v. More info: - OS = OpenSuse 13.1 -

...en how many of the model names are reused for very different hardware, it can be helpful to see at least the first few digits of a serial number, but in this case, I don't think we have too many other reports of this hardware to go on. The closest ones seem to be: http://networkupstools.org/ddl/Tripp_Lite/SMART2200RMXL2U.html > If I understand the NUT process correctly, it looks for this LB status in order to create the POWERDOWNFLAG. "In upsmon.conf, add a POWERDOWNFLAG directive with a filename. upsmon will create this file when the UPS needs to be powered off during a power failure whe...

...nstalled nut and tried to configure based on your HCL (which I did not check before buying...) Doesn't "just work" - help? this page says that my model is NOT on the HCL, but the drop downs on the search seemed to say otherwise? (see attachment) https://networkupstools.org/ddl/Tripp_Lite/ lsusb shows Bus 001 Device 004: ID 09ae:3024 Tripp Lite  The error shows:  nut-driver.service - Network UPS Tools - power device driver controller    Loaded: loaded (/lib/systemd/system/nut-driver.service; static; vendor preset: enabled)    Active: failed (Result: exit-code) since Tu...

Hello, I've got Tripplite Smart Int 1000 UPS with lan4.1 serial interface. Quite sympathetic UPS, I must say from first glance. I have made a proper serial cable (btw i hate all those constructor's decisions to make distinct serial wiring for each and every UPS type from each and every manufacturer!) I use [tripplite] driver for NUT and I can use upsc to get report from UPS, but

Thanks again for your help, Charles. I was able to install the Tripp Lite software on my Ubuntu machine, and it sort of works. It does something which continually changes the USB device ID of the UPS, and prints voluminous error messages in the log. However, one of the things that it can do is to schedule a UPS shutdown, which Nut does not know how to do. So I monitored the USB port with

...en how many of the model names are reused for very different hardware, it can be helpful to see at least the first few digits of a serial number, but in this case, I don't think we have too many other reports of this hardware to go on. The closest ones seem to be: http://networkupstools.org/ddl/Tripp_Lite/SMART2200RMXL2U.html > If I understand the NUT process correctly, it looks for this LB status in order to create the POWERDOWNFLAG. "In upsmon.conf, add a POWERDOWNFLAG directive with a filename. upsmon will create this file when the UPS needs to be powered off during a power failure whe...

Hi Everyone, New to the list. Thanks in advance for any assistance you are able to provide. I have a TrippLite SMART2200RM2UN UPS. I have installed and configured NUT as instructed on the website, and am able to monitor the status of the UPS without much problem. The only problem I am seeing is that I cannot get the machine to actually send a Low Battery ( LB ) signal. When I run

I have a Tripp-Lite BCPERS450, connected to a system running Ubuntu 16.04.3 LTS and NUT 2.7.2-4ubuntu1.2. I had to make my own /lib/systemd/system-shutdown/nutshutdown, but now everything is working except for powering on and off the UPS. Regardless of the settings of offdelay and ondelay in upsconf, and regardless of whether the AC power is on, when I say "upsdrvctl shutdown" the UPS