search for: tdm_voice

...p://www.voip-info.org/wiki/index.php?page=Asterisk+ss7+setup I have the cross over cable between them. however, wanpipe shows connected but the signaling link does not align. i have my configs for host A ##wanpipe1.conf [devices] wanpipe1 = WAN_AFT_TE1, Comment [interfaces] w1g1 = wanpipe1, , TDM_VOICE, Comment [wanpipe1] CARD_TYPE = AFT S514CPU = A CommPort = PRI AUTO_PCISLOT = NO PCISLOT = 4 PCIBUS = 15 FE_MEDIA = E1 FE_LCODE = HDB3 FE_FRAME = NCRC4 FE_LINE = 1 TE_CLOCK = MASTER TE_REF_CLOCK = 0 TE_HIGHIMPEDANCE...

...'s my planed setup : PRI from telco <--> (port 1 of A104d) * (port 2 of A104d) <--> PM3 The PM3, for those who don't know is lucent's portmaster RAS dial-up router. I had setup asterisk, zaptel, libpri, wanpipe (as I have sangoma's cards). In wancfg, I have port 1 as TDM_VOICE, with hardware echo on, span 1. Port 2 is TDM_VOICE, without hw echo, Clock as master, reference 0 (for the time being, I'm still not hooked up with my pri, will be 1 in the future), span 2. I alswo had to enable High Impedance on port 2 to operate without alarms. Zaptel.conf: ------------...

...39;re tied down by limiting software and excessive licensing costs. Thanks! Geraint pri show spans shows all spans as up and active. zap show status shows all as ok wanrouter status shows all as connected wanpipe1 and 2: [devices] wanpipe1 = WAN_AFT_TE1, Comment [interfaces] w1g1 = wanpipe1, , TDM_VOICE, Comment [wanpipe1] CARD_TYPE = AFT S514CPU = A CommPort = PRI AUTO_PCISLOT = NO PCISLOT = 1 PCIBUS = 16 FE_MEDIA = E1 FE_LCODE = HDB3 FE_FRAME = CRC4 FE_LINE = 1 TE_CLOCK = NORMAL TE_REF_CLOCK = 0 TE_SIG_MODE = CC...

...Running * 1.0.9, Zaptel 1.0.9, FC2 yum-updated to current, quad Xeon. Production box, handles 2-6 thousand calls a day, snom 360 handsets w/ latest firmware, load average never goes over 2.0 My conf files: wanpipe1.conf: [devices] wanpipe1 = WAN_AFT_TE1, Comment [interfaces] w1g1 = wanpipe1, , TDM_VOICE, Comment [wanpipe1] CARD_TYPE = AFT S514CPU = A CommPort = PRI AUTO_PCISLOT = NO PCISLOT = 4 PCIBUS = 1 FE_MEDIA = T1 FE_LCODE = B8ZS FE_FRAME = ESF FE_LINE = 1 TE_CLOCK = NORMAL TE_REF_CLOCK = 0 TE_HIGHIMPEDANCE = NO LBO = 0DB FE_TXTRISTATE = NO MTU = 1500 UDPPORT = 9000 TTL = 255...

I have installed Asterisk on a CentOS4 box and then installed Asterisk from CVS. I installed a Sangoma A101 and connected it to a Adtran 600 using a T1 Crossover cable. The 600 has 12 x FXS, 12 x FXO interfaces. I ran through the wanpipe install instructions and configured it, now I can run [root@altpbx asterisk]# wanrouter hwprobe ------------------------------- | Wanpipe Hardware Probe Info

...onfigure the card for CAS, it will never connect. My card is currently configured (and makes only outgoing calls) as: E1 PRI, CCS, HDB3,NCRC4 (i have no idea what dss1 is or where it goes) My /etc/wanpipe/wanpipe1.conf is: [devices] wanpipe1 = WAN_AFT_TE1, Comment [interfaces] w1g1 = wanpipe1, , TDM_VOICE, Comment [wanpipe1] CARD_TYPE = AFT S514CPU = A CommPort = PRI AUTO_PCISLOT = NO PCISLOT = 1 PCIBUS = 4 FE_MEDIA = E1 FE_LCODE = HDB3 FE_FRAME = NCRC4 FE_LINE = 1 TE_CLOCK = NORMAL TE_REF_CLOCK = 0 TE_SIG_MODE = CC...

...f you want to edit this file, it is # recommended that you use wancfg program # to do so. #================================================ # Sangoma Technologies Inc. #================================================ [devices] wanpipe1 = WAN_AFT, Comment [interfaces] w1g1 = wanpipe1, , TDM_VOICE, Comment [wanpipe1] CARD_TYPE = AFT S514CPU = A CommPort = PRI AUTO_PCISLOT = YES PCISLOT = 1 PCIBUS = 1 FE_MEDIA = E1 FE_LCODE = HDB3 FE_FRAME = CRC4 FE_LINE = 1 TE_CLOCK = NORMAL ACTIVE_CH = ALL TE_HIGHIMPEDANCE = NO INTERFACE = V35 CLOCKING = EXTERNAL BaudRate = 2048 MTU = 2048 UDPPO...

...onfigure the card for CAS, it will never connect. My card is currently configured (and makes only outgoing calls) as: E1 PRI, CCS, HDB3,NCRC4 (i have no idea what dss1 is or where it goes) My /etc/wanpipe/wanpipe1.conf is: [devices] wanpipe1 = WAN_AFT_TE1, Comment [interfaces] w1g1 = wanpipe1, , TDM_VOICE, Comment [wanpipe1] CARD_TYPE = AFT S514CPU = A CommPort = PRI AUTO_PCISLOT = NO PCISLOT = 1 PCIBUS = 4 FE_MEDIA = E1 FE_LCODE = HDB3 FE_FRAME = NCRC4 FE_LINE = 1 TE_CLOCK = NORMAL TE_REF_CLOCK = 0 TE_SIG_MODE = CC...

I upgraded from Tormenta2 to Sangoma A101. I followed the instructions, and installation was successful. zttool, ztcfg, all show card is installed properly. I copied the parameters from my old working zaptel.conf, zapata.conf and zapata-auto.conf. Verified on Sangoma website that these files are correct. Also configured wanpipe1.conf. But doing all this didn't start the PRI channels. It says

...t to edit this file, it is # recommended that you use wancfg program # to do so. #================================================ # Sangoma Technologies Inc. #================================================ [devices] wanpipe1 = WAN_AFT_ANALOG, Comment [interfaces] w1g1 = wanpipe1, , TDM_VOICE, Comment [wanpipe1] CARD_TYPE = AFT S514CPU = A CommPort = PRI AUTO_PCISLOT = NO PCISLOT = 6 PCIBUS = 1 FE_MEDIA = FXO/FXS TDMV_LAW = MULAW TDMV_OPERMODE = FCC MTU = 1500 UDPPORT = 9000 TTL = 255 IGNORE_FRONT_...

...nd debugging output: ==begin zaptel.conf ==================== loadzone=us defaultzone=us span=1,0,0,ccs,hdb3 bchan=1-15,17-31 hardhdlc=16 ==end zaptel.conf ====================== ==begin wanpipe1.conf ================== [devices] wanpipe1 = WAN_AFT_TE1, Comment [interfaces] w1g1 = wanpipe1, , TDM_VOICE, Comment [wanpipe1] CARD_TYPE = AFT S514CPU = A CommPort = PRI AUTO_PCISLOT = NO PCISLOT = 4 PCIBUS = 13 FE_MEDIA = E1 FE_LCODE = HDB3 FE_FRAME = NCRC4 FE_LINE = 1 TE_CLOCK = NORMAL TE_REF_CLOCK = 0 TE_...

...an = 3,3,0,ccs,hdb3,crc4,yellow span = 4,4,0,ccs,hdb3,crc4,yellow #channel definitions #bchan = 1-15, 17-31, 32-46, 48-62, 63-77, 79-93, 94-108, 110-124 #dchan = 16,47,78,109 bchan = 1-15,17-124 dchan = 16 my wanpipe1.conf [devices] wanpipe1 = WAN_AFT_TE1, Comment [interfaces] w1g1 = wanpipe1, , TDM_VOICE, Comment [wanpipe1] CARD_TYPE = AFT S514CPU = A CommPort = PRI AUTO_PCISLOT = NO PCISLOT = 13 PCIBUS = 6 FE_MEDIA = E1 FE_LCODE = HDB3 FE_FRAME = NCRC4 FE_LINE = 1 TE_CLOCK = NORMAL TE_REF_CLOCK = 0 TE_HIGHIMPEDANCE...

...how to validate this setup? I am running all this on ubuntu lucid, kernel 2.6.32. Asterisk version 11.5.0 Dahdi 2.6.1 Wanpipe 7.0.3 Here's a few config snippets: wanpipe1.conf (the other wanpipe.conf files are similar) [devices] wanpipe1 = WAN_AFT_TE1, Comment [interfaces] w1g1 = wanpipe1, , TDM_VOICE, Comment [wanpipe1] CARD_TYPE = AFT S514CPU = A CommPort = PRI AUTO_PCISLOT = NO PCISLOT = 4 PCIBUS = 5 FE_MEDIA = E1 FE_LCODE = HDB3 FE_FRAME = NCRC4 FE_LINE = 1 TE_CLOCK = NORMAL TE_REF_CLOCK = 0 TE_SIG_MODE = CC...

...f you want to edit this file, it is # recommended that you use wancfg program # to do so. #================================================ # Sangoma Technologies Inc. #================================================ [devices] wanpipe1 = WAN_AFT, Comment [interfaces] w1g1 = wanpipe1, , TDM_VOICE, Comment [wanpipe1] CARD_TYPE = AFT S514CPU = A CommPort = PRI AUTO_PCISLOT = YES PCISLOT = 2 PCIBUS = 1 FE_MEDIA = E1 FE_LCODE = HDB3 FE_FRAME = CRC4 FE_LINE = 1 TE_CLOCK = NORMAL ACTIVE_CH = ALL TE_HIGHIMPEDANCE = YES MTU = 1500 UDPPORT = 9000 TTL = 255 IGNORE_FRONT_END = NO TDMV_SPA...

...h FCS check on channel 16. Here is my /etc/zaptel.conf # MFC/R2 normalmente no usa CRC4 span=1,0,0,cas,hdb3 cas=1-15:1101 dchan=16 cas=17-31:1101 This configuration works with Digium cards. Here is the wanpipe1.conf file: [devices] wanpipe1 = WAN_AFT, Comment [interfaces] w1g1 = wanpipe1, , TDM_VOICE, Comment [wanpipe1] CARD_TYPE = AFT S514CPU = A CommPort = PRI AUTO_PCISLOT = NO PCISLOT = 2 PCIBUS = 1 FE_MEDIA = E1 FE_LCODE = HDB3 FE_FRAME = NCRC4 FE_LINE = 1 TE_CLOCK = NORMAL TE_REF_CLOCK = 0 TE_HIGHIMPEDANCE...

...s echocancelwhenbridged=yes echotraining=yes adsi=no callprogress=no switchtype => euroisdn signalling => pri_cpe callgroup => 1 group => 1 immediate => no channel => 1-10 ##EOF ##/etc/wanpipe/wanpipe1.conf [devices] wanpipe1 = WAN_AFT, Comment [interfaces] w1g1 = wanpipe1, , TDM_VOICE, Comment [wanpipe1] CARD_TYPE = AFT S514CPU = A CommPort = PRI AUTO_PCISLOT = NO PCISLOT = 0 PCIBUS = 1 FE_MEDIA = E1 FE_LCODE = HDB3 FE_FRAME = CRC4 FE_LINE = 1 TE_CLOCK = NORMAL TE_REF_CLOCK = 0 ACTIVE_CH = ALL...

Hi, got a Sangoma A200 with a bunch of extension cards and having real problems getting it to deal with a normal single BT line Symptoms are that incoming calls are fine. Outgoing calls ring the far end, BUT asterisk never sees that the call is answered (ie no message in the logs files saying so), as a result the remove end can hear the PBX side talking, but there is no audio back from the

...1-23 dchan = 24 Here's the Zapata files ------------------------------------ [channels] zcontext = from-pstn switchtype = national pridialplan = national signalling = pri_net group = 0 channel => 1-23 wanpipe1.conf [devices] wanpipe1 = WAN_AFT, Comment [interfaces] w1g1 = wanpipe1, , TDM_VOICE, Comment [wanpipe1] CARD_TYPE = AFT S514CPU = A CommPort = PRI AUTO_PCISLOT = NO PCISLOT = 5 PCIBUS = 2 FE_MEDIA = T1 FE_LCODE = B8ZS FE_FRAME = ESF FE_LINE = 1 TE_CLOCK = NORMAL ACTIVE_CH = ALL TE_HIGHIMPEDANCE...

...f you want to edit this file, it is # recommended that you use wancfg program # to do so. #================================================ # Sangoma Technologies Inc. #================================================ [devices] wanpipe1 = WAN_AFT, Comment [interfaces] w1g1 = wanpipe1, , TDM_VOICE, Comment [wanpipe1] CARD_TYPE = AFT S514CPU = A CommPort = PRI AUTO_PCISLOT = YES PCISLOT = 2 PCIBUS = 1 FE_MEDIA = E1 FE_LCODE = HDB3 FE_FRAME = NCRC4 FE_LINE = 1 TE_CLOCK = NORMAL TE_REF_CLOCK = 0 ACTIVE_CH = ALL TE_HIGHIMPEDANCE = YES FE_TXTRISTATE = NO MTU = 2100 UDPPORT = 9000 TTL...

[This email is either empty or too large to be displayed at this time]