Displaying 20 results from an estimated 50 matches for "tdm410".
Did you mean:
tdm400
2009 Jun 10
3
Query about tdm410 cards
Hi
recently bought a soekris net5501 and a tdm410 to place in there.
I am having some issues attaching 12V power to the card via the molex
card - basically the box for the motherboard is too small.
I have read up about a PWR2400b and it seems to use 2wire pin, I am
guessing to connect to P8 just behind the molex connector on the tdm410.
can any...
2016 Jan 05
3
Detected alarm on channel 3: Red Alarm
Hi everyone!
I have a Digium Card TDM410
But, it appear for me this massege
chan_dahdi.c:8061 handle_alarms: Detected alarm on channel 3: Red Alarm
But my line is ok!
But sometimes it back
sig_analog.c:3807 analog_handle_init_event: Alarm cleared on channel 2
But it again back to red alarm.
What can be happen?
My lines is all ok!...
2009 Jun 23
1
How to force TDM410 to alaw
Hi
I am having some problem forcing my tdm410 to alaw over ulaw, I have
1.6.1.0 asterisk (debian i486)
dahdi 1:2.2.0 built with the hardware echo canceller firmware
/etc/asterisk/chan_dahdi.conf
alaw=1-4
but I have this in the general section, before any channel definition
dahdi show channel 1
Default law: ulaw
even when i h...
2012 Jun 18
1
TDM410 PTSN line setup with 1 analog phone
Hello, I have a current asterisk 1.8.13.0 asterisk-addons 1.6.24 asterisk-sounds
1.2.1 dahdi-linux-complete 2.6.1+2.6.1 libpri 1.4.12 and asterisk-gui 2.1.0.rc1
(not trying to use the gui, want to do everything by hand) with a TDM410 with
2FXO and 2FXS. I have my POTS (PTNS) line plugged into port 1 (FXO) and a
analog phone connected to port 3 (FXS). I compiled asterisk with asterisk
samples so I realize that may have messed me up.
This is all running on Ubuntu Server 12.04. I have been googling/researching
reading t...
2008 May 20
5
Server recommendation help
...have determined it
is because of a IRQ problem and have decided to get a new server. Can
anyone suggest a server grade setup that supports this? I would rather
not buy a machine that will be unstable. I am not opposed to building
one if need be.
Cards I have installed:
Digium TE205P - 5v
TDM410
Thanks for any suggestions
Richard
--
This message was scanned by ESVA and is believed to be clean.
2009 Dec 08
1
Configure DAHDI with TDM410 for analog Modem calls
Hello,
I am currently trying to configure an Asterisk (current 1.4) box with a TDM410P and 2 FXS as well as 2FXO modules.
An analog modem is directly connected to the TDM (port 4) which itself is directly connected to the PSTN (port 1).
[V.34 Modem]-----[TDM on Ast. 1.4 TDM]---PSTN
When I try to establish an analog modem connection with this setup, the modem is unable to connect...
2009 Dec 09
1
Configure DAHDI with TDM410 for analog
Hello,
I am now working on a project which need data modem calls passing trough
asterisk with a TDM card. But i found out (as Mr Greg woods) that it was
impossible. So know i am trying doing this using an E1/T1 card (TE110P). I
am still working on it so we can help each other to find a solution to
this.
2011 Jan 06
0
TDM410 and DSL
Hi all,
I have a system installation in Guam with two trunks. One has a DSL service
riding on it with the usual filter. That channel however keeps throwing
alarms. I bypassed the filter and it stopped throwing alarms, but of course
the high frequencies annoy the users. I swapped the filters and the alarms
came back.
Any suggestions? Could I have a bad DSL modem?
Cassius
-------------- next
2010 Feb 18
0
Digium TDM410 passthrought to KVM VM trixbox
Hello, my name is Paul.
I need to map a PCI device for a virtual machine.
The Linux distribution is Ubuntu server 9.10, infrastructure
virtualization is "KVM". The virtual machine will install trixbox. To
map the PCI card is a "Digium TDM410p.
There currently, KVM hosts a virtual machine that runs smoothly
without any problems. In fact, this virtual machine is running
Openfiler and has direct access to 2 physical disks installed on the
server.
Creating a new virtual machine can not connect the Digium card,
directly to the virtu...
2016 Jan 05
2
Detected alarm on channel 3: Red Alarm
...digium.com] On Behalf Of Vitor Mazuco
>> Sent: Tuesday, January 05, 2016 9:21 AM
>> To: Asterisk Users Mailing List - Non-Commercial Discussion
>> Subject: [asterisk-users] Detected alarm on channel 3: Red Alarm
>>
>> Hi everyone!
>>
>> I have a Digium Card TDM410
>>
>> But, it appear for me this massege
>>
>> chan_dahdi.c:8061 handle_alarms: Detected alarm on channel 3: Red Alarm
>>
>> But my line is ok!
>>
>> But sometimes it back
>>
>> sig_analog.c:3807 analog_handle_init_event: Alarm cleared on...
2009 Jun 28
1
Sangoma A200
Hi
I was wondering if any one has used these cards, I am looking at this as
a replacement for the tdm410, I have some issues with installing the
tdm410 in a small case because of the power plug being at the end of the
board.
I am in australia seems like we have a different setup for out fxs
voltage, any one in oz using this card ?
Thanks
Alex
-------------- next part --------------
A non-text atta...
2009 May 14
2
Problem with Asterisk + TDM410 FXO
...r from legacy PABX + PSTN
lines to VOIP infrastructure.
I borrowed a spa9000 to place between the PABX and the PSTN lines. I
have had this going for a while (>5 months) and it has been working fine
(some issues with echo and other minor things), which is why I am moving
to asterisk.
I bought a tdm410 with 3 fxo + fxs. The fxs is connected to a fax line
and used just in case the internet connection is down.
I have tested the pstn line connection with a soft phone and it seems to
be working fine. I need some help on how to tell asterisk to ignore the
line for incoming !
when I connect the PABX...
2008 Oct 12
3
setup for fax machine
...a ( chan_dahdi ) set
faxdetect=incoming
then the dial plan would have
[incoming-pstn]
exten => fax,1,Dial(DAHDI/1) ; the fax machine
exten => fax,2,Hangup()
exten => s,1,Answer()
exten => s,2,Dial(DAHDI/2) ; internal extension
.............
Would this work? I'll need another TDM410 card to do this, so I'd like
some reassurance before I go purchase it.
sean
2008 May 05
3
TDM410P driver?
Quick and dirty question: for the TDM410P I must use the wctdm24xxp driver?
Att
Vin?cius Fontes
Desenvolvimento
Canall Tecnologia em Comunica??es Ltda.
2008 Feb 15
7
Digium stopped TDM400P production: alternatives??
Hi,
Digium stopped to produce TDM400P and the new TDM410 is too new to find
it in our shops. The only alternative available is a "fully-compatible"
Openvox product...but is it really "fully-compatible"? Any experience
about Openvox products (card and zaptel versions, etc...)?
Thank you!
Giorgio.
2009 Oct 07
2
system cmd + fax line
Hi
I have a site that has asterisk install with a tdm410 one port is
connected to a pstn that is used as a backup outbound line when/if the
internet/voip is unavailable.
Currently my dial plan for this line is to ignore it, I just basically
do a
s,1,noop
s,n,wait (60)
s,n,hangup
what I would like to do is if I call from a certain number be given an...
2010 Sep 15
2
incoming call FXO
Hi all,
Recently I have instaled one Digium TDM410 on my Asterisk. After instaled , I can do outgoing calls but I cant receive calls. I receive the following messages:
chan_dahdi.c: Got event 2 (Ring/Answered)...[Sep 14 11:24:44] NOTICE[2654] chan_dahdi.c: Got event 18 (Ring Begin)...[Sep 14 11:24:44] WARNING[2654] pbx.c: Channel 'DAHDI/4-1...
2009 Apr 29
2
Something wrong with DAHDI signalling according to the CLI
I have Asterisk 1.4.24 en a Digium TDM410 with EC and with 3 FXO
modules.
When I plug one PSTN-line into a FXO-port I am able to receive calls on
this line and I can also make calls from an internal SIP-phone to the
external PSTN-network.
Still I am bothered about something that appears on the CLI when I do a
reload chan_dahdi.so :
aste...
2004 Apr 12
1
Re: Booting error - Unable to specify channel 2:
...able to remove
parallel and serial interfaces as well since nothing is connect to this
box. Here's what I have now:
0: 27713309 XT-PIC timer
1: 167 XT-PIC keyboard
2: 0 XT-PIC cascade
3: 277073215 XT-PIC wctdm <------ TDM410
4: 1114724 XT-PIC eth0
7: 277082652 XT-PIC wcfxo <------ X100P
8: 1 XT-PIC rtc
9: 277077218 XT-PIC wcfxo <------ X100P
12: 0 XT-PIC PS/2 Mouse
14: 102780 XT-PIC ide0
15: 3...
2009 May 15
1
how to ignore a ring on a line
Hi
I have a fxs (tdm410 ) connected to a pstn that is primarily used for
faxing, it is meant to be a just in case line.
How do I tell asterisk to ignore the line completely - ie don;t pick up
when it rings ?
Alex
--
"I will have a foreign-handed foreign policy."
- George W. Bush
09/27/2000
Redwood, CA
---...