search for: freshmakers

Greetings all, I'm new to asterisk... Finally got two IP phones and two TDM400P's (one with four FXO modules and one with four FXS modules)... Began experimenting a couple days ago and have ran into a very aggrevating problem. My system consists of the following hardware: Abit BL7-RAID motherboard Pentium 4 1.6GHz processor 512MB SDRAM 2 TDM400P cards 2 3Com 3c905

No matter what I do, I've tried now three different motherboards, my TDM400P keeps giving 'Freshmaker failed register test' after emitting a list of xx != 00 errors. Anyone have any clues for me? I'm wondering if I got a bad module or what. TIA -- Undocumented Features quote of the moment... "It's not the one bullet with your name on it that you have to worry about;

The REV I card shows up in the PCI table as: 02:05.0 Network controller: Tiger Jet Network Inc. Intel 537 (or 02:05.0 Class 0280: e159:0001) Subsystem: Unknown device b119:0001 But the REV E/F shows up as: 02:0d.0 Communication controller: Tiger Jet Network Inc. Tiger3XX Modem/ISDN interface (or 02:0d.0 Class 0780: e159:0001) Subsystem: Unknown device b100:0003 One

Hi, We have two of these 4 port FXO cards. However, we are having some problems with incoming/outgoing calls. The latest version of Asterisk/zaptel from CVS is being used. Voicemail, internal SIP <-> SIP calls between Pingtel xpressa hard phones work terrific, echotest is fine, and so on. The zaptel and wcfxs modules load fine, and show all 8 FXO interfaces in dmesg:

hi guys, i got a TDM400P FXS card an everything is fine except for this when i do modprobe wcfxs , the linux shows 2 TigerJet Network Inc Model 300 128k. i don't know why it is showing 2 of them. or is that what it is? ERROR: Freshmaker version: 63 Freshmaker passed register test ProSLIC on module 0 insane (1) 0 should be 2 Module 0: Not installed ProSLIC on module 1 insane (1) 0 cshould be

Hi , I have an asterix (1.2.7.1) box with 3 TDM400P and 10 FXO modules, and zaptel (1.2.5). The problem is that 6 modules can't be initaized and i get the folowing error: May 7 09:17:37 WARNING[7739] chan_zap.c: Unable to specify channel 9: No such device May 7 09:17:37 ERROR[7739] chan_zap.c: Unable to open channel 9: No such device here = 0, tmp->channel = 9, channel = 9 ztcfg output

I apparently have a dead FXS module. Is there any kind of test I can run on it (on a live system) to determine if its good or bad? The telephone has no dialtone, gets no calls. It has been working for several months, and just quit yesterday. Thanks! Found a Wildcard TDM: Wildcard TDM400P REV I (4 modules) Freshmaker version: 73 Freshmaker passed register test Module 0: Installed -- AUTO

Hi i have buy a Digium TDM400P with 1 fxo modules TDM01B for connect my asterisk to a french analog line. In my zaptel.conf, i have: loadzone=fr defaultzone=fr fxols=3 when i load the module, i have in logs: Nov 24 06:13:40 gw kernel: Freed a Wildcard Nov 24 06:13:40 gw kernel: Zapata Telephony Interface Unloaded Nov 24 06:13:40 gw zaptel: Removing zaptel module: succeeded Nov 24

Hi, I have received a new card TDM400P revision E, from digium. When I tried to modprobe wcfxs it gave me the following errors: Freshmaker version: 63 Freshmaker passed register test ProSLIC on module 0 insane (1) 255 should be 2 Module 0: Not installed ProSLIC on module 1 insane (1) 255 should be 2 Module 1: Not installed ProSLIC on module 2 insane (1) 255 should be 2 Module 2: Not installed

I have a TDM400. Just updated Fedora 12 to kernel 2.6.32. Rebuilt and installed dahdi-2.2.1. kernel modules loaded. lsmod | grep wctdm wctdm 37233 0 dahdi 194985 1 wctdm lsmod | grep dahdi dahdi 194985 1 wctdm crc_ccitt 1549 2 dahdi,isdnhdlc dmesg: dahdi: Telephony Interface Registered on major 196 dahdi: Version: 2.2.1

Hi- I'm totally stumped configuring my TDM400P with one FXS and one FXO module. Before I got the FXO module, I used to have an X101P, and everything was working very well. Now * doesn't seem to recognize the FXO channel. I've searched the wiki and the list archives. Stock Debian 3.0 stable installation. Any advice? Thanks. -- David Here's my configuration: modprobe zaptel

I am having trouble with chan_zap.so not loading. When I load it from modules.conf, Asterisk bails out without any error message. When I load it from the console, it just says "Unable to load module chan_zap.so" no matter what verbose level I am using. dmesg says: Zaptel Version: 1.4.4 Zaptel Echo Canceller: MG2 Freshmaker version: 73 Freshmaker passed register test Module 0:

I installed the TDM400P and installed it on a system running on Fedora Core1, please refer to the steps below. I connected an analogue phone to the FXS port. When I pick up the speaker I don't hear the dialtone although when I press a number key I hear a DTMF generated. What could be the problem? I appreciate your help 1- First I installed the TDM400P in the PCI slot and connected

I'm running Asterisk on a Gentoo box with the Zaptel 1.2.1 drivers. If I boot the machine without having the wcfxs module autoload, then install the module with modprobe, asterisk works just fine. If I boot the machine and autoload the wcfxs module, the module loads fine: > Jan 11 11:06:55 asterisk Zapata Telephony Interface Registered on major 196 > Jan 11 11:06:55 asterisk ACPI: PCI

I have read thru what other users have tried in this list when they have experienced seemingly similar issues to what I have, without success. I suspect there might be an issue regarding both the X100P and TDM04b cards being used in an Intel SE7525GP2 motherboard, as I had to even wait for a BIOS update from Intel in order to utilize my 3ware 9500 SATA raid controller on it (3ware Kb -->

Hi all, I'm trying to install a TDM400P card, and I need some help. Please, see below... after dmesg command: [root@voip root]# dmesg via82cxxx: board #1 at 0xD800, IRQ 5 Zapata Telephony Interface Registered on major 196 PCI: Found IRQ 3 for device 00:09.0 PCI: Sharing IRQ 3 with 00:10.1 Freshmaker version: 71 Freshmaker passed register test Module 0: Installed -- AUTO FXS/DPO Module 1:

From asterisk -cvvvvv == Parsing '/etc/asterisk/chan_dahdi.conf': == Found == Parsing '/etc/asterisk/users.conf': == Found -- Automatically generated pseudo channel [Nov 11 17:43:28] WARNING[5756]: chan_dahdi.c:18155 process_dahdi: Ignoring any changes to 'userbase' (on reload) at line 23. [Nov 11 17:43:28] WARNING[5756]: chan_dahdi.c:18155 process_dahdi:

Looking for some help from the UK please. I backed up all my Asterisk configuration before re-installing the server from 32 -> 64 bit. Unfortunately I did not transfer the backup to another machine!!!!! I now have a TDM400P that is not picking up the line. Can you see what I have done wrong when I have rebuilt the config please: dahdi_scan ---------- [1] active=yes alarms=OK

Hi, I am struggling to get rid of a conflict on DELL 2800 : PCI Parity error (EB113 on the display) I am learning linux and asterisk as I go along, there might be obvious things I should know, but bear with me. >From demsg below my 2 digium cards installed are listed (no config or connections done to digium cards yet), the conflict is with the TDM400P card, without that card, in any slot, no

Hi all, I was wondering if anyone had any pointers on how to determine whether or not a module has gone wonky on the TDM400P? I have a 2 FXO (channels 3 and 4) and 2 FXS unit (channels 1 and 2). The bad (?) module in question is the FXO module on channel 3. I can't dial in to or out of that channel; dialing in gives a busy signal, dialing out just shows * hanging around after attempting a