search for: dss1

...------ CAPI Subsystem Rev 1.1.2.8 capifs: Rev 1.1.2.3 capi20: Rev 1.1.2.7: started up with major 68 (middleware+capifs) Modular ISDN Stack core $Revision: 1.37 $ mISDNd: kernel daemon started (current:ca4d8680) mISDNd: test event done ISDN L1 driver version 1.18 ISDN L2 driver version 1.31 mISDN: DSS1 Rev. 1.42 mISDN Capi 2.0 driver file version 1.20 ISAC module $Revision: 1.17 $ mISDN_dsp: Audio DSP Rev. 1.24 (debug=0x0) EchoCancellor MG2 dtmftreshold(100) mISDN_dsp: DSP clocks every 64 samples. This equals 8 jiffies. DTMF modul version 1.16 Traverse Tech. NETjet-S driver, revision 1.6 nj_prob...

...uld it be possible to mail me a few bits of the important config files? Sorry if I should have included something else too, but let me know and I'll provide it! Steve My capi.conf is as follows: # card file proto io irq mem cardnr options #b1isa b1.t4 DSS1 0x150 7 - - P2P b1pci b1.t4 DSS1 - - - - c4 c4.bin DSS1 - - - - c4 - DSS1 - - - - c4 - DSS1 - - - - P2P c4 -...

Hi, I am requesting for a E1 connection from my telco. They are asking if I want DSS1 or SS7, and I am stuck here. Could someone tell me the difference between the two? How should I decide which one to use? Thanks in advance for your help. Mark -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachm...

...ccountcode= context=Amt callgroup=2 devices=2 [ISDN1] isdnmode=ptp msn=3899231 incomingmsn=* controller=1,2,3 softdtmf=1 accountcode= context=Intern-ISDN callgroup=1 devices=6 /etc/capi.conf #SuSEconfig.isdn generated # card file proto io irq mem cardnr options c4 c4.bin DSS1 - - - 1 p2p c4 - DSS1 - - - 2 p2p c4 - DSS1 - - - 3 p2p c4 - DSS1 - - - 4 p2p Versions: net-misc/asterisk-chan_capi-cm-0.5.4 net-misc/asterisk-1.0.8-r1 +als...

...ies of /etc/asterisk/extensions.conf ====================================== s,1,Dial,CAPI/523065:b${EXTEN}|30 s,1,Dial,CAPI/523065:${EXTEN}|30|r Here's my /etc/isdn/capi.conf ===================== # card file proto io irq mem cardnr options #b1isa b1.t4 DSS1 0x150 7 - - P2P b1pci b1.t4 DSS1 - - - - c4 c4.bin DSS1 - - - - c4 - DSS1 - - - - c4 - DSS1 - - - - P2P c4 -...

Has anyone a working /etc/asterisk/capi.conf example for Germany or Switzerland using the AVM C4 - ISDN Card. I try to connect asterisk to 3 wires BRI-ISDN (Swisscom). I appreciate your help and it would save me a lot of time, figuring it out by myself. regards, Claudio

I am going to try to figure out why mu asterisk box connected by back to back cable to an PRI appliance is not going to send the PROGRESSING dss1 message. In fact i see the SETUP and the follwing CALL PROCEEDING but not the PROGRESSING so the appliance doesn't allow the "early audio" !!!!! this is my zapata.conf [channels] context = ser switchtype = euroisdn usecallerid = yes echocancel = yes echocancelwhenbridged = yes relaxd...

...But i can't connect to my ISDN Line. misdnportinfo gives (what does ":Layer 4 protocol 0x04000001 is detected, but not allowed for TE lib" mean?): best regards and thanks t. asterix asterisk # misdnportinfo Port 1: TE-mode BRI S/T interface line (for phone lines) -> Protocol: DSS1 (Euro ISDN) -> Layer 4 protocol 0x04000001 is detected, but not allowed for TE lib. -> childcnt: 2 * Port NOT useable for PBX (maybe there is already a PBX running?) -------- Port 2: TE-mode BRI S/T interface line (for phone lines) -> Protocol: DSS1 (Euro ISDN) -> Layer 4 protocol...

...estings, I can see channel is respectively up (with patton web server status page) and OK (with dahdi_tool) from both sides but I can't dial a single call ("Unable to create DAHDI for unknown reason...") from asterisk to patton. In my setup, my main settings are : Smartnode side: dss1,Net,pp,q931,q921 B410P side: euroisdn,bri_cpe,span=1,1,0,ccs,ami,bchan=1-2,hardhdlc=3 Both devices lights are green but I think this only means layer1 diag is OK. Looking at http://en.wikipedia.org/wiki/Digital_Subscriber_System_No._1, I would say DSS1 and EuroISDN are the same (but that doesn'...

...BT tell me there's no problem they can see with the ISDN line involved. jd This is the dialstring : exten => _9.,1,SetCallerPres(allowed) exten => _9.,2,SetCIDNum(252000) exten => _9.,3,Dial(CAPI/g1/${EXTEN:1}/b) exten => _9.,4,Congestion /etc/capi.conf contains : c2 c2.bin DSS1 - - - - P2P c2 c2.bin DSS1 - - - - P2P /etc/asterisk/capi.conf contains : [general] nationalprefix=0 internationalprefix=00 rxgain=0.9 txgain=0.3 ; interface sections ... [ISDN1] isdnmode=DID incomingmsn=* controller=1 group=1 softdtmf=on relaxdtmf=on accountcode= context=capi-in holdtype=hold...

...e a Digium B410P 4-port BRI card. I installed misdn 1.1.3 with hfcmulti driver and misdnuser 1.1.3. I configured the card "correctly" as misdnportinfo reports: # misdnportinfo Port 1: TE-mode BRI S/T interface line (for phone lines) -> Interface is Poin-To-Point. -> Protocol: DSS1 (Euro ISDN) -> childcnt: 2 -------- Port 2: TE-mode BRI S/T interface line (for phone lines) -> Interface is Poin-To-Point. -> Protocol: DSS1 (Euro ISDN) -> childcnt: 2 -------- Port 3: TE-mode BRI S/T interface line (for phone lines) -> Interface is Poin-To-Point. -> Prot...

Hi list, I am searching for a possibility to do a certain call transfer method which is called "path replacement" in QSIG. But I want to do that in DSS1 (EuroISDN). If my asterisk does a call transfer I want the machine to signalize on dchan that the call path has to be replaced to a direct connect between the caller and the called, i.e. my machine is to hang up after the transfer and the channels are free again. Is it possible and with what card v...

...(level, low) -> IRQ 5 c4: PCI BIOS reports AVM-C2 at i/o 0xd000, irq 5, mem 0xe1000000 kcapi: Controller 1: c2-d000 attached kcapi: Controller 2: c2-d000 attached c4: AVM C2 at i/o 0xd000, irq 5, mem 0xe1000000 c4: revision 1.1.2.2 c2-d000: card 1 "C2" ready. c2-d000: card 1 Protocol: DSS1 c2-d000: card 1 Linetype: point to multipoint c2-d000: C2-card (3.11-04) now active kcapi: card 1 "c2-d000" ready. c2-d000: card 2 "C2" ready. c2-d000: card 2 Protocol: DSS1 c2-d000: card 2 Linetype: point to multipoint c2-d000: C2-card (3.11-04) now active kcapi: card 2 "c...

...clude zapata-auto.conf Zapata-auto.conf has: callerid=asreceived ;Sangoma A102 port 1 [slot:1 bus:4 span: 1] switchtype=euroisdn context=from-pstn group=0 signalling=pri_cpe channel => 1-15,17-31 Note: According to the tech support in the local telco, my E1 should be: E1 PRI, CAS, HDB3, NCRC4, DSS1 However if I configure the card for CAS, it will never connect. My card is currently configured (and makes only outgoing calls) as: E1 PRI, CCS, HDB3,NCRC4 (i have no idea what dss1 is or where it goes) My /etc/wanpipe/wanpipe1.conf is: [devices] wanpipe1 = WAN_AFT_TE1, Comment [interfaces] w1g1...

...to that interface. The asterisk and diva drivers are working ok but i cannot communicate to outside via this bri. Xlite gives me the message: "call failed: declined". Anyone have experience with this setup? What are the main parameters for bri card configuration? D-channel protocol: ETSI-DSS1 or other? Interface mode: NT or TE? Direct Inward Dialing (DID): Yes ou no? (MSN ou DID?) Thanks by any kind of help! Best regards, PS.

Hallo all, I am trying to get * with chan_capi and a ptp-ISDN with 4 lines on a AVM C4 card to work. But weather inbound nor outbound is working :( My capi.conf: ; ; CAPI config ; ; [general] nationalprefix=0 internationalprefix=00 rxgain=0.8 txgain=0.8 [interfaces] mode=immediate isdnmode=ptp msn=8993 incomingmsn=* mode=immediate controller=1,2,3,4 softdtmf=1 ;accountcode= context=demo

Hi All, We've got msidn configured: Port 1: TE-mode BRI S/T interface line (for phone lines) -> Protocol: DSS1 (Euro ISDN) -> childcnt: 2 -------- mISDN_close: fid(3) isize(131072) inbuf(0x8fd5060) irp(0x8fd5060) iend(0x8fd5060) and running on Asterisk 1.4.21.2: pbx*CLI> misdn show stacks BEGIN STACK_LIST: * Port 1 Type TE Prot. PMP L2Link UP L1Link:UP Blocked:0 Debug:0 but I'm not sure...

Hi To troubleshoot FreeBSD panics triggered by ISDN load on an asterisk system, we are looking to buy an ISDN call generator/simulator device. The minimum requirements include: - Not too expensive - PRI support (BRI support is a plus) - CCS+CRC4 farming + HDB3 coding - EuroISDN (DSS1) support. - A minimum of 4 ports (120 channels/concurrent calls) - Compatibility with Digium cards. - DUT in TE mode. - Reliable & stable operation. I would like to hear your recommendations for and experiences about such a device. Recommendations on hand crafted systems using Asterisk, DAHDI...

Hi, I am using Asterisk on a DSS1 ISDN-BRI with ISDN4Linux (and a Fritz Card PnP). The ISDN-BRI is in PTP-Mode (Point to Point "german: Anlagenanschluss") which is enabled within I4L with "hisaxctrl fcpcipnp0 7 1". Everything works fine except that I can not see the called number/MSN of incoming calls within A...

Hi We interfaced our ASCOTEL PBX to Asterisk. by EuroISDN PRI , DSS1 It works fine on channels 1- 15, but on 17-31 the miststood each other. Asterisk speaks in Timeslots, the PBX in B-channels The signalling is ok, but the bridging is shifted. The first incoming connection is bridged to "nirwana" also no indication is hearable, calling a second internal...