search for: bpviol

...) (Slaves: 01) 1 channels to configure. orange:~# and my zaptel.conf file contains orange:~# more /etc/zaptel.conf fxsks=1 loadzone=uk defaultzone=uk orange:~# but zap show status in the command line shows orange*CLI> zap show status Description Alarms IRQ bpviol CRC4 Fra Codi Options LBO Wildcard X100P Board 1 OK 0 0 0 CAS Unk YEL 0 db (CSU)/0-133 feet (DSX-1) orange*CLI> and i think the Unk means unknown...? Does anyone have any ideas on how to get this line to work, ive followed every howto i can find, and goo...

...one=us dynamic=eth,eth1/00:30:48:84:74:25,24,0 bchan=1-23 dhcan=24 /etc/asterisk/zapata.conf: under [channels]: signalling=pri_net switchtype=5ess callerid=asreceived group=1 context=default channel => 1-23 *CLI> zap show status Description Alarms IRQ bpviol CRC4 T4XXP (PCI) Card 0 Span 1 OK 0 0 0 T4XXP (PCI) Card 0 Span 2 UNCONFIGUR 0 0 0 T4XXP (PCI) Card 0 Span 3 UNCONFIGUR 0 0 0 T4XXP (PCI) Card 0 Span 4 UNCONFIGUR...

...ster, medium devsel, latency 32, IRQ 201 I/O ports at c800 [size=256] Memory at fe000000 (32-bit, non-prefetchable) [size=4K] Capabilities: [40] Power Management version 2 Identified as: *CLI> zap show status Description Alarms IRQ bpviol CRC4 Wildcard X101P Board 1 OK 0 0 0 And the following lines in zapata.conf(for spanish lines): answeronpolarityswitch=yes hanguponpolarityswitch=yes The problem is that although the calls work correctly the system is unable to detect a pstn hangup and it...

...MFC/R2. here goes my zaptel.conf: span=1,0,0,ccs,hdb3,crc4 cas=1-15:1101 dchan=16 cas=17-31:1101 span=2,0,0,ccs,hdb3,crc4 cas=32-46:1101 dchan=47 cas=48-62:1101 The first strange behavior is that the: zap show status shows this: Description Alarms IRQ bpviol CRC4 T4XXP (PCI) Card 0 Span 1 OK 0 0 0 T4XXP (PCI) Card 0 Span 2 OK 0 0 0 T4XXP (PCI) Card 0 Span 3 OK 0 0 0 T4XXP (PCI) Card 0 Span 4 UNCONFIGUR 0...

...6 from-pstn en default In Service 7 from-pstn en default In Service 8 from-pstn en default In Service dahdi show status Description Alarms IRQ bpviol CRC4 Fra Codi Options LBO Wildcard TE120P Card 0 OK 1 0 0 ESF B8ZS YEL 0 db (CSU)/0-133 feet (DSX-1) CLI> dahdi show version DAHDI Version: 2.1.0.4 Echo Canceller: MG2 What should I try next? Any help appreciated. sean

...means the card is unable to detect the battery. I've plugged a test but into the loop through on the card, dialtone is there. I've tried reversing the polarity, two way/three way jack leads (I'm in the UK) but none the less I get: Description Alarms IRQ bpviol CRC4 Fra Codi Options LBO Wildcard X100P Board 1 RED 0 0 0 CAS Unk YEL 0 db (CSU)/0-133 feet (DSX-1) Is this likely to be bad hardware (hostility towards this cheap card noted) or software/driver? It would be just ace to crack this problem and learn some mor...

...D-channel of span 1 [Aug 16 10:26:10] NOTICE[8002]: chan_dahdi.c:3043 my_handle_dchan_exception: PRI got event: HDLC Abort (6) on D-channel of span 1 I am also showing CRC4 errors on span as well. # asterisk -rx "dahdi show status" Description Alarms IRQ bpviol CRC4 Fra Codi Options LBO T2XXP (PCI) Card 0 Span 1 OK 1 0 2938622 ESF B8ZS 0 db (CSU)/0-133 feet (DSX-1) I am leaning towards a misconfiguration on the span on the switch side but here is my setup. Can anyone point me in the right direction? # dahdi_hardwa...

...uot; message, and when I receive calls, asterisk doesn't seems to care (don't get anything on the CLI) I'm using Asterisk 1.2.17 and Zaptel 1.2.16 from Xorcom's repository voip:~# asterisk -rx 'zap show status' Description Alarms IRQ bpviol CRC4 Wildcard TDM400P REV I Board 1 OK 0 0 0 voip:~# asterisk -rx 'zap show channels' Chan Extension Context Language MusicOnHold pseudo from-internal es 1 from-internal es 2 from-intern...

Hello, I'm just starting out with asterisk and I'm playing around with the system. Currently I have a Digium TE210P connected to a PRI on the Asterisk server. I have a SIP soft phone on my laptop for testing that is working fine. When I try to place a call from my soft phone I get this from Asterisk: May 1 09:11:41 NOTICE[20098]: app_dial.c:1029 dial_exec_full: Unable to create

Hi All, I have installed Asterisk 1.4.2 and have loaded ztdummy as I have no Digium cards. The problem I have is that MOH will not play. It starts and then stops. asterisk*CLI> zap show status Description Alarms IRQ bpviol CRC4 ZTDUMMY/1 1 UNCONFIGUR 0 0 0 I'm not sure if the above is correct. Please help. Thanks. -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20070327/...

...r7445 Echo Canceller(s): MG2 Configuration ====================== Channel map: Channel 01: FXS Kewlstart (Default) (Echo Canceler: mg2) (Slaves: 01) 1 channels to configure. Setting echocan for channel 1 to mg2 *CLI> dahdi show status Description Alarms IRQ bpviol CRC4 Fra Codi Options LBO Wildcard X101P Board 1 OK 0 0 0 CAS Unk YEL 0 db (CSU)/0-133 feet (DSX-1) but when I run dahdi show channels I can only see the psuedo channel: *CLI> dahdi show channels Chan Extension Context Language MOH Interpre...

...e to create channel of type 'DAHDI' (cause 0 - Unknown) == Everyone is busy/congested at this time (1:0/0/1) And yet the line isn't busy or congested - nothing's using it. The output of dsx*CLI> dahdi show status Description Alarms IRQ bpviol CRC4 Wildcard TDM400P REV E/F Board 5 OK 0 0 0 is fine, as is: dsx*CLI> dahdi show channels Chan Extension Context Language MOH Interpret pseudo default default 1 incoming d...

...les/3.8.13/dahdi? to /lib/modules/3.8.13-bone43? and then do a? depmod -a 3.8.13-bone43 Then dahdi installs. I do not use any dahdi modules so no modules install. In asterisk I get the following - beaglebone*CLI> dahdi show status Description????????????????????????????? Alarms???? IRQ??????? bpviol???? CRC4? beaglebone*CLI> dahdi show channels ?? Chan Extension? Context???????? Language?? MOH Interpret ?pseudo??????????? default??????????????????? default If dahdi installs and at least appears to work with asterisk does that mean that it is compiled correctly? I am trying to figure out...

...s to configure. Setting echocan for channel 1 to mg2 Setting echocan for channel 2 to mg2 Setting echocan for channel 3 to mg2 Setting echocan for channel 4 to mg2 The problem is about asterisk CLI results: asterisk*CLI> dahdi show status Description Alarms IRQ bpviol CRC4 Fra Codi Options LBO Wildcard TDM400P REV I Board 5 OK 0 0 0 CAS Unk YEL 0 db (CSU)/0-133 feet (DSX-1) asterisk*CLI> dahdi show channels Chan Extension Context Language MOH Interpret Blocked State pseudo defaul...

Hi all, We have our system hosted publicly and 4 phones are connected remotely at employee's home, and when they try to do a assisted transfer to one of the employee at the main office, the call is lost. For ex: person A calls person B, person B calls person C for assisted transfer, and as soon as person B hits transfer button again to transfer person A to C, the call is lost. But in the

...t;wanpipe1> context=default group=0 echocancel=yes signalling=fxs_ks channel => 1 context=default group=0 echocancel=yes signalling=fxs_ks channel => 2 dahdi show version DAHDI Version: 2.1.0.4 Echo Canceller: MG2 dahdi show status Description Alarms IRQ bpviol CRC4 Fra Codi Options LBO wrtdm Board 1 OK 0 0 0 CAS Unk YEL 0 db (CSU)/0-133 feet (DSX-1) dahdi show channels Chan Extension Context Language MOH Interpret Blocked State pseudo from-zaptel...

Calling out on PSTN over a TDM400P seems to generate a Red Alarm - whatever that is. I have another extension on the PSTN, and I can dial out over that. zttool shows no alarms. asterisk*CLI> zap show status Description Alarms IRQ bpviol CRC4 Fra Codi Options LBO Wildcard TDM400P REV I Board 1 OK 0 0 0 CAS Unk YEL 0 db (CSU)/0-133 feet (DSX-1) -- Starting simple switch on 'Zap/2-1' -- Executing [2560597 at internal:1] Answer("Zap/2-1", "") in new stack --...

...tion=Wildcard TDM400P REV I Board 5 name=WCTDM/4 manufacturer=Digium devicetype=Wildcard TDM400P REV I location=PCI Bus 01 Slot 06 basechan=1 totchans=4 irq=16 type=analog port=1,FXS port=2,FXS port=3,none port=4,FXO CLI> dahdi show status Description Alarms IRQ bpviol CRC4 Fra Codi Options LBO Wildcard TDM400P REV I Board 5 OK 0 0 0 CAS Unk YEL 0 db (CSU)/0-133 feet (DSX-1) But if I dial in, no dial tone, nothing on the cli. And: *CLI> dahdi show channels Chan Extension Context Language MOH Interpret Blocked...

...rom-pstn default In Service 2 from-pstn default In Service 3 from-pstn default In Service 4 from-pstn default In Service 5 from-pstn default In Service 6 from-pstn default In Service 7 from-pstn default In Service 8 from-pstn default In Service pbx*CLI> dahdi show status Description Alarms IRQ bpviol CRC4 Fra Codi Options LBO Xorcom XPD #00/00: FXO OK 0 0 0 CAS Unk YEL 0 db (CSU)/0-133 feet (DSX-1) pbx*CLI> dahdi show regdump 1 Unable to get registers on channel 1 Unable to get stats on channel 1 [Trixbox]# dahdi_hardware -v /usr/sbin/dahdi_hardware: warning - OLD DRIVER: missing '/sy...

...ickupgroup=1 immediate=no ;callerid=6216000 ; signalling = pri_cpe group = 2 channel => 32-46, 48-62 group = 3 channel => 63-77, 79-93 group = 4 channel => 94-108, 110-124 the channel status *CLI> zap show status Description Alarms IRQ bpviol CRC4 wanpipe1 card 0 OK 0 0 0 wanpipe2 card 1 RED 0 0 0 wanpipe3 card 2 RED 0 0 0 wanpipe4 card 3 RED 0 0...