OK, reporting back.
I edited ups.conf again and set ondelay to 0 again. At the same time I defined
offdelay as 60. After this I rebooted the pi and - tata - it works.
I did at last three test circuits (pulling the cord), NUT shuts down system on
low battery, 60 seconds later UPS loses power. After the unit is on line again
power returns and everything is coming up as expected.
So far I am satisfied with this setting, hopefully it will work that way in case
of a real power down.
Thanks a lot for your patience. And thanks a lot for the software itself.
-----Ursprüngliche Nachricht-----
Von: Nut-upsuser Im Auftrag von EP
Gesendet: Sonntag, 27. Oktober 2019 14:28
An: Nut-upsuser at alioth-lists.debian.net
Betreff: Re: [Nut-upsuser] Problems with NUT on Raspberry Pi
I checked it with the Windows machine. There are nearly no parameters to set
directly to the ups. The only thing to set is the low battery-state. All other
settings seem to run on the windows machine only.
Ups.delay.start was set to 30 after Windows-configuration. The rest seems to be
unattended:
Init SSL without certificate database
battery.charge: 64
battery.charge.low: 10
battery.charge.warning: 20
battery.mfr.date: CPS
battery.runtime: 960
battery.runtime.low: 300
battery.type: PbAcid
battery.voltage: 13.4
battery.voltage.nominal: 12
device.mfr: CPS
device.model: OR600ELCDRM1U
device.type: ups
driver.name: usbhid-ups
driver.parameter.ondelay: -1
driver.parameter.pollfreq: 30
driver.parameter.pollinterval: 10
driver.parameter.port: auto
driver.parameter.synchronous: no
driver.version: 2.7.4
driver.version.data: CyberPower HID 0.4
driver.version.internal: 0.41
input.transfer.high: 263
input.transfer.low: 160
input.voltage: 233.0
input.voltage.nominal: 230
output.voltage: 233.0
ups.beeper.status: enabled
ups.delay.shutdown: 20
ups.delay.start: 30
ups.load: 40
ups.mfr: CPS
ups.model: OR600ELCDRM1U
ups.productid: 0601
ups.realpower.nominal: 360
ups.status: OL CHRG
ups.test.result: Done and passed
ups.timer.shutdown: -60
ups.timer.start: -60
ups.vendorid: 0764
Any suggestions? I can't believe I am the only guy using this unit and
facing these problems.
-----Ursprüngliche Nachricht-----
Von: Nut-upsuser Im Auftrag von Roger Price
Gesendet: Sonntag, 27. Oktober 2019 11:56
An: Nut-upsuser at alioth-lists.debian.net
Betreff: Re: [Nut-upsuser] Problems with NUT on Raspberry Pi
On Sun, 27 Oct 2019, EP wrote:
> I can't imagine that's the way cyberpower wants their unit to work.
> With this behavior the unit does exactly the opposite of what it is
> built for. It doesn't protect your equipment. It will destroy it
> because the server which was just shutted down cleanly will boot again
> on a battery-powererd ups. What a crap.
>
> But I am not finished at all because I can't believe there is no
> solution for this problem.
Perhaps it's time to borrow a Windows PC and try the software that comes
with
the UPS. Roger
_______________________________________________
Nut-upsuser mailing list
Nut-upsuser at alioth-lists.debian.net
https://alioth-lists.debian.net/cgi-bin/mailman/listinfo/nut-upsuser
_______________________________________________
Nut-upsuser mailing list
Nut-upsuser at alioth-lists.debian.net
https://alioth-lists.debian.net/cgi-bin/mailman/listinfo/nut-upsuser