Karol Herbst
2019-Jun-03 13:18 UTC
[Nouveau] [PATCH v2 4/4] pci: save the boot pcie link speed and restore it on fini
@bjorn: any further ideas? Otherwise I'd like to just go ahead and fix this issue inside Nouveau and leave it there until we have a better understanding or non Nouveau cases of this issue. On Tue, May 21, 2019 at 7:48 PM Karol Herbst <kherbst at redhat.com> wrote:> > doing the same on the bridge controller with my workarounds applied: > > please note some differences: > LnkSta: Speed 8GT/s (ok) vs Speed 2.5GT/s (downgraded) > SltSta: PresDet+ vs PresDet- > LnkSta2: Equalization stuff > Virtual channel: NegoPending- vs NegoPending+ > > both times I executed lspci while the GPU was still suspended. > > 00:01.0 PCI bridge: Intel Corporation Xeon E3-1200 v5/E3-1500 v5/6th > Gen Core Processor PCIe Controller (x16) (rev 05) (prog-if 00 [Normal > decode]) > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- > ParErr- Stepping- SERR- FastB2B- DisINTx- > Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- > <TAbort- <MAbort- >SERR- <PERR- INTx- > Latency: 0 > Interrupt: pin A routed to IRQ 16 > Bus: primary=00, secondary=01, subordinate=01, sec-latency=0 > I/O behind bridge: 0000e000-0000efff [size=4K] > Memory behind bridge: ec000000-ed0fffff [size=17M] > Prefetchable memory behind bridge: > 00000000c0000000-00000000d1ffffff [size=288M] > Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- > <TAbort- <MAbort+ <SERR- <PERR- > BridgeCtl: Parity- SERR- NoISA- VGA- VGA16+ MAbort- >Reset- FastB2B- > PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- > Capabilities: [88] Subsystem: Dell Device 07be > Capabilities: [80] Power Management version 3 > Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA > PME(D0+,D1-,D2-,D3hot+,D3cold+) > Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME- > Capabilities: [90] MSI: Enable- Count=1/1 Maskable- 64bit- > Address: 00000000 Data: 0000 > Capabilities: [a0] Express (v2) Root Port (Slot+), MSI 00 > DevCap: MaxPayload 256 bytes, PhantFunc 0 > ExtTag- RBE+ > DevCtl: CorrErr- NonFatalErr- FatalErr- UnsupReq- > RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop- > MaxPayload 256 bytes, MaxReadReq 128 bytes > DevSta: CorrErr- NonFatalErr- FatalErr- UnsupReq- > AuxPwr- TransPend- > LnkCap: Port #2, Speed 8GT/s, Width x16, ASPM L0s L1, > Exit Latency L0s <256ns, L1 <8us > ClockPM- Surprise- LLActRep- BwNot+ ASPMOptComp+ > LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- CommClk+ > ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt- > LnkSta: Speed 8GT/s (ok), Width x16 (ok) > TrErr- Train- SlotClk+ DLActive- BWMgmt+ ABWMgmt+ > SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- > HotPlug- Surprise- > Slot #1, PowerLimit 75.000W; Interlock- NoCompl+ > SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- > CmdCplt- HPIrq- LinkChg- > Control: AttnInd Unknown, PwrInd Unknown, > Power- Interlock- > SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- > PresDet+ Interlock- > Changed: MRL- PresDet+ LinkState- > RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- > PMEIntEna- CRSVisible- > RootCap: CRSVisible- > RootSta: PME ReqID 0000, PMEStatus- PMEPending- > DevCap2: Completion Timeout: Not Supported, > TimeoutDis-, LTR+, OBFF Via WAKE# ARIFwd- > AtomicOpsCap: Routing- 32bit+ 64bit+ 128bitCAS+ > DevCtl2: Completion Timeout: 50us to 50ms, > TimeoutDis-, LTR+, OBFF Via WAKE# ARIFwd- > AtomicOpsCtl: ReqEn- EgressBlck- > LnkCtl2: Target Link Speed: 8GT/s, EnterCompliance- SpeedDis- > Transmit Margin: Normal Operating Range, > EnterModifiedCompliance- ComplianceSOS- > Compliance De-emphasis: -6dB > LnkSta2: Current De-emphasis Level: -6dB, > EqualizationComplete+, EqualizationPhase1+ > EqualizationPhase2+, EqualizationPhase3+, > LinkEqualizationRequest- > Capabilities: [100 v1] Virtual Channel > Caps: LPEVC=0 RefClk=100ns PATEntryBits=1 > Arb: Fixed- WRR32- WRR64- WRR128- > Ctrl: ArbSelect=Fixed > Status: InProgress- > VC0: Caps: PATOffset=00 MaxTimeSlots=1 RejSnoopTrans- > Arb: Fixed+ WRR32- WRR64- WRR128- TWRR128- WRR256- > Ctrl: Enable+ ID=0 ArbSelect=Fixed TC/VC=ff > Status: NegoPending- InProgress- > Capabilities: [140 v1] Root Complex Link > Desc: PortNumber=02 ComponentID=01 EltType=Config > Link0: Desc: TargetPort=00 TargetComponent=01 > AssocRCRB- LinkType=MemMapped LinkValid+ > Addr: 00000000fed19000 > Capabilities: [d94 v1] Secondary PCI Express <?> > Kernel driver in use: pcieport > 00: 86 80 01 19 07 00 10 00 05 00 04 06 00 00 81 00 > 10: 00 00 00 00 00 00 00 00 00 01 01 00 e0 e0 00 20 > 20: 00 ec 00 ed 01 c0 f1 d1 00 00 00 00 00 00 00 00 > 30: 00 00 00 00 88 00 00 00 00 00 00 00 ff 01 10 00 > 40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 > 50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 > 60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 > 70: 00 00 00 00 00 00 00 00 00 62 17 00 00 00 00 0a > 80: 01 90 03 c8 08 00 00 00 0d 80 00 00 28 10 be 07 > 90: 05 a0 00 00 00 00 00 00 00 00 00 00 00 00 00 00 > a0: 10 00 42 01 01 80 00 00 20 00 00 00 03 ad 61 02 > b0: 40 00 03 d1 80 25 0c 00 00 00 48 00 00 00 00 00 > c0: 00 00 00 00 80 0b 08 00 00 64 00 00 0e 00 00 00 > d0: 43 00 1e 00 00 00 00 00 00 00 00 00 00 00 00 00 > e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 > f0: 00 00 00 84 4e 01 01 20 00 00 00 00 e0 00 10 00 > > On Tue, May 21, 2019 at 7:35 PM Karol Herbst <kherbst at redhat.com> wrote: > > > > was able to get the lspci prints via ssh. Machine rebooted > > automatically each time though. > > > > relevant dmesg: > > kernel: nouveau 0000:01:00.0: Refused to change power state, currently in D3 > > kernel: nouveau 0000:01:00.0: Refused to change power state, currently in D3 > > kernel: nouveau 0000:01:00.0: Refused to change power state, currently in D3 > > kernel: nouveau 0000:01:00.0: tmr: stalled at ffffffffffffffff > > > > (last one is a 64 bit mmio read to get the on GPU timer value) > > > > # lspci -vvxxx -s 0:01.00 > > 00:01.0 PCI bridge: Intel Corporation Xeon E3-1200 v5/E3-1500 v5/6th > > Gen Core Processor PCIe Controller (x16) (rev 05) (prog-if 00 [Normal > > decode]) > > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- > > ParErr- Stepping- SERR- FastB2B- DisINTx- > > Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- > > <TAbort- <MAbort- >SERR- <PERR- INTx- > > Latency: 0 > > Interrupt: pin A routed to IRQ 16 > > Bus: primary=00, secondary=01, subordinate=01, sec-latency=0 > > I/O behind bridge: 0000e000-0000efff [size=4K] > > Memory behind bridge: ec000000-ed0fffff [size=17M] > > Prefetchable memory behind bridge: > > 00000000c0000000-00000000d1ffffff [size=288M] > > Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- > > <TAbort- <MAbort+ <SERR- <PERR- > > BridgeCtl: Parity- SERR- NoISA- VGA- VGA16+ MAbort- >Reset- FastB2B- > > PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- > > Capabilities: [88] Subsystem: Dell Device 07be > > Capabilities: [80] Power Management version 3 > > Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA > > PME(D0+,D1-,D2-,D3hot+,D3cold+) > > Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME- > > Capabilities: [90] MSI: Enable- Count=1/1 Maskable- 64bit- > > Address: 00000000 Data: 0000 > > Capabilities: [a0] Express (v2) Root Port (Slot+), MSI 00 > > DevCap: MaxPayload 256 bytes, PhantFunc 0 > > ExtTag- RBE+ > > DevCtl: CorrErr- NonFatalErr- FatalErr- UnsupReq- > > RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop- > > MaxPayload 256 bytes, MaxReadReq 128 bytes > > DevSta: CorrErr- NonFatalErr- FatalErr- UnsupReq- > > AuxPwr- TransPend- > > LnkCap: Port #2, Speed 8GT/s, Width x16, ASPM L0s L1, > > Exit Latency L0s <256ns, L1 <8us > > ClockPM- Surprise- LLActRep- BwNot+ ASPMOptComp+ > > LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- CommClk+ > > ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt- > > LnkSta: Speed 2.5GT/s (downgraded), Width x16 (ok) > > TrErr- Train- SlotClk+ DLActive- BWMgmt+ ABWMgmt+ > > SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- > > HotPlug- Surprise- > > Slot #1, PowerLimit 75.000W; Interlock- NoCompl+ > > SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- > > HPIrq- LinkChg- > > Control: AttnInd Unknown, PwrInd Unknown, > > Power- Interlock- > > SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- > > PresDet- Interlock- > > Changed: MRL- PresDet+ LinkState- > > RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- > > PMEIntEna- CRSVisible- > > RootCap: CRSVisible- > > RootSta: PME ReqID 0000, PMEStatus- PMEPending- > > DevCap2: Completion Timeout: Not Supported, > > TimeoutDis-, LTR+, OBFF Via WAKE# ARIFwd- > > AtomicOpsCap: Routing- 32bit+ 64bit+ 128bitCAS+ > > DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-, > > LTR+, OBFF Via WAKE# ARIFwd- > > AtomicOpsCtl: ReqEn- EgressBlck- > > LnkCtl2: Target Link Speed: 8GT/s, EnterCompliance- SpeedDis- > > Transmit Margin: Normal Operating Range, > > EnterModifiedCompliance- ComplianceSOS- > > Compliance De-emphasis: -6dB > > LnkSta2: Current De-emphasis Level: -6dB, > > EqualizationComplete-, EqualizationPhase1- > > EqualizationPhase2-, EqualizationPhase3-, > > LinkEqualizationRequest- > > Capabilities: [100 v1] Virtual Channel > > Caps: LPEVC=0 RefClk=100ns PATEntryBits=1 > > Arb: Fixed- WRR32- WRR64- WRR128- > > Ctrl: ArbSelect=Fixed > > Status: InProgress- > > VC0: Caps: PATOffset=00 MaxTimeSlots=1 RejSnoopTrans- > > Arb: Fixed+ WRR32- WRR64- WRR128- TWRR128- WRR256- > > Ctrl: Enable+ ID=0 ArbSelect=Fixed TC/VC=ff > > Status: NegoPending+ InProgress- > > Capabilities: [140 v1] Root Complex Link > > Desc: PortNumber=02 ComponentID=01 EltType=Config > > Link0: Desc: TargetPort=00 TargetComponent=01 > > AssocRCRB- LinkType=MemMapped LinkValid+ > > Addr: 00000000fed19000 > > Capabilities: [d94 v1] Secondary PCI Express <?> > > Kernel driver in use: pcieport > > 00: 86 80 01 19 07 00 10 00 05 00 04 06 00 00 81 00 > > 10: 00 00 00 00 00 00 00 00 00 01 01 00 e0 e0 00 20 > > 20: 00 ec 00 ed 01 c0 f1 d1 00 00 00 00 00 00 00 00 > > 30: 00 00 00 00 88 00 00 00 00 00 00 00 ff 01 10 00 > > 40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 > > 50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 > > 60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 > > 70: 00 00 00 00 00 00 00 00 00 62 17 00 00 00 00 0a > > 80: 01 90 03 c8 08 00 00 00 0d 80 00 00 28 10 be 07 > > 90: 05 a0 00 00 00 00 00 00 00 00 00 00 00 00 00 00 > > a0: 10 00 42 01 01 80 00 00 20 00 00 00 03 ad 61 02 > > b0: 40 00 01 d1 80 25 0c 00 00 00 08 00 00 00 00 00 > > c0: 00 00 00 00 80 0b 08 00 00 64 00 00 0e 00 00 00 > > d0: 43 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 > > e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 > > f0: 00 40 01 00 4e 01 01 22 00 00 00 00 e0 00 10 00 > > > > lspci -vvxxx -s 1:00.00 > > 01:00.0 3D controller: NVIDIA Corporation GP107M [GeForce GTX 1050 > > Mobile] (rev ff) (prog-if ff) > > !!! Unknown header type 7f > > Kernel driver in use: nouveau > > Kernel modules: nouveau > > 00: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff > > 10: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff > > 20: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff > > 30: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff > > 40: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff > > 50: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff > > 60: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff > > 70: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff > > 80: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff > > 90: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff > > a0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff > > b0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff > > c0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff > > d0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff > > e0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff > > f0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff > > > > On Tue, May 21, 2019 at 4:30 PM Karol Herbst <kherbst at redhat.com> wrote: > > > > > > On Tue, May 21, 2019 at 4:13 PM Bjorn Helgaas <helgaas at kernel.org> wrote: > > > > > > > > On Tue, May 21, 2019 at 03:28:48PM +0200, Karol Herbst wrote: > > > > > On Tue, May 21, 2019 at 3:11 PM Bjorn Helgaas <helgaas at kernel.org> wrote: > > > > > > On Tue, May 21, 2019 at 12:30:38AM +0200, Karol Herbst wrote: > > > > > > > On Mon, May 20, 2019 at 11:20 PM Bjorn Helgaas <helgaas at kernel.org> wrote: > > > > > > > > On Tue, May 07, 2019 at 10:12:45PM +0200, Karol Herbst wrote: > > > > > > > > > Apperantly things go south if we suspend the device with a different PCIE > > > > > > > > > link speed set than it got booted with. Fixes runtime suspend on my gp107. > > > > > > > > > > > > > > > > > > This all looks like some bug inside the pci subsystem and I would prefer a > > > > > > > > > fix there instead of nouveau, but maybe there is no real nice way of doing > > > > > > > > > that outside of drivers? > > > > > > > > > > > > > > > > I agree it would be nice to fix this in the PCI core if that's > > > > > > > > feasible. > > > > > > > > > > > > > > > > It looks like this driver changes the PCIe link speed using some > > > > > > > > device-specific mechanism. When we suspend, we put the device in > > > > > > > > D3cold, so it loses all its state. When we resume, the link probably > > > > > > > > comes up at the boot speed because nothing did that device-specific > > > > > > > > magic to change it, so you probably end up with the link being slow > > > > > > > > but the driver thinking it's configured to be fast, and maybe that > > > > > > > > combination doesn't work. > > > > > > > > > > > > > > > > If it requires something device-specific to change that link speed, I > > > > > > > > don't know how to put that in the PCI core. But maybe I'm missing > > > > > > > > something? > > > > > > > > > > > > > > > > Per the PCIe spec (r4.0, sec 1.2): > > > > > > > > > > > > > > > > Initialization – During hardware initialization, each PCI Express > > > > > > > > Link is set up following a negotiation of Lane widths and frequency > > > > > > > > of operation by the two agents at each end of the Link. No firmware > > > > > > > > or operating system software is involved. > > > > > > > > > > > > > > > > I have been assuming that this means device-specific link speed > > > > > > > > management is out of spec, but it seems pretty common that devices > > > > > > > > don't come up by themselves at the fastest possible link speed. So > > > > > > > > maybe the spec just intends that devices can operate at *some* valid > > > > > > > > speed. > > > > > > > > > > > > > > I would expect that devices kind of have to figure out what they can > > > > > > > operate on and the operating system kind of just checks what the > > > > > > > current state is and doesn't try to "restore" the old state or > > > > > > > something? > > > > > > > > > > > > The devices at each end of the link negotiate the width and speed of > > > > > > the link. This is done directly by the hardware without any help from > > > > > > the OS. > > > > > > > > > > > > The OS can read the current link state (Current Link Speed and > > > > > > Negotiated Link Width, both in the Link Status register). The OS has > > > > > > very little control over that state. It can't directly restore the > > > > > > state because the hardware has to negotiate a width & speed that > > > > > > result in reliable operation. > > > > > > > > > > > > > We don't do anything in the driver after the device was suspended. And > > > > > > > the 0x88000 is a mirror of the PCI config space, but we also got some > > > > > > > PCIe stuff at 0x8c000 which is used by newer GPUs for gen3 stuff > > > > > > > essentially. I have no idea how much of this is part of the actual pci > > > > > > > standard and how much is driver specific. But the driver also wants to > > > > > > > have some control over the link speed as it's tight to performance > > > > > > > states on GPU. > > > > > > > > > > > > As far as I'm aware, there is no generic PCIe way for the OS to > > > > > > influence the link width or speed. If the GPU driver needs to do > > > > > > that, it would be via some device-specific mechanism. > > > > > > > > > > > > > The big issue here is just, that the GPU boots with 8.0, some on-gpu > > > > > > > init mechanism decreases it to 2.5. If we suspend, the GPU or at least > > > > > > > the communication with the controller is broken. But if we set it to > > > > > > > the boot speed, resuming the GPU just works. So my assumption was, > > > > > > > that _something_ (might it be the controller or the pci subsystem) > > > > > > > tries to force to operate on an invalid link speed and because the > > > > > > > bridge controller is actually powered down as well (as all children > > > > > > > are in D3cold) I could imagine that something in the pci subsystem > > > > > > > actually restores the state which lets the controller fail to > > > > > > > establish communication again? > > > > > > > > > > > > 1) At boot-time, the Port and the GPU hardware negotiate 8.0 GT/s > > > > > > without OS/driver intervention. > > > > > > > > > > > > 2) Some mechanism reduces link speed to 2.5 GT/s. This probably > > > > > > requires driver intervention or at least some ACPI method. > > > > > > > > > > there is no driver intervention and Nouveau doesn't care at all. It's > > > > > all done on the GPU. We just upload a script and some firmware on to > > > > > the GPU. The script runs then on the PMU inside the GPU and this > > > > > script also causes changing the PCIe link settings. But from a Nouveau > > > > > point of view we don't care about the link before or after that script > > > > > was invoked. Also there is no ACPI method involved. > > > > > > > > > > But if there is something we should notify pci core about, maybe > > > > > that's something we have to do then? > > > > > > > > I don't think there's anything the PCI core could do with that > > > > information anyway. The PCI core doesn't care at all about the link > > > > speed, and it really can't influence it directly. > > > > > > > > > > 3) Suspend puts GPU into D3cold (powered off). > > > > > > > > > > > > 4) Resume restores GPU to D0, and the Port and GPU hardware again > > > > > > negotiate 8.0 GT/s without OS/driver intervention, just like at > > > > > > initial boot. > > > > > > > > > > No, that negotiation fails apparently as any attempt to read anything > > > > > from the device just fails inside pci core. Or something goes wrong > > > > > when resuming the bridge controller. > > > > > > > > I'm surprised the negotiation would fail even after a power cycle of > > > > the device. But if you can avoid the issue by running another script > > > > on the PMU before suspend, that's probably what you'll have to do. > > > > > > > > > > there is none as far as we know. Or at least nothing inside the vbios. > > > We still have to get signed PMU firmware images from Nvidia for full > > > support, but this still would be a hacky issue as we would depend on > > > those then (and without having those in redistributable form, there > > > isn't much we can do about except fixing it on the kernel side). > > > > > > > > > 5) Now the driver thinks the GPU is at 2.5 GT/s but it's actually at > > > > > > 8.0 GT/s. > > > > > > > > > > what is actually meant by "driver" here? The pci subsystem or Nouveau? > > > > > > > > I was thinking Nouveau because the PCI core doesn't care about the > > > > link speed. > > > > > > > > > > Without knowing more about the transition to 2.5 GT/s, I can't guess > > > > > > why the GPU wouldn't work after resume. From a PCIe point of view, > > > > > > the link is supposed to work and the device should be reachable > > > > > > independent of the link speed. But maybe there's some weird > > > > > > dependency between the GPU and the driver here. > > > > > > > > > > but the device isn't reachable at all, not even from the pci > > > > > subsystem. All reads fail/return a default error value (0xffffffff). > > > > > > > > Are these PCI config reads that return 0xffffffff? Or MMIO reads? > > > > "lspci -vvxxxx" of the bridge and the GPU might have a clue about > > > > whether a PCI error occurred. > > > > > > > > > > that's kind of problematic as it might just lock up my machine... but > > > let me try that. > > > > > > > > > It sounds like things work if you return to 8.0 GT/s before suspend, > > > > > > things work. That would make sense to me because then the driver's > > > > > > idea of the link state after resume would match the actual state. > > > > > > > > > > depends on what is meant by the driver here. Inside Nouveau we don't > > > > > care one bit about the current link speed, so I assume you mean > > > > > something inside the pci core code? > > > > > > > > > > > But I don't see a way to deal with this in the PCI core. The PCI core > > > > > > does save and restore most of the architected config space around > > > > > > suspend/resume, but since this appears to be a device-specific thing, > > > > > > the PCI core would have no idea how to save/restore it. > > > > > > > > > > if we assume that the negotiation on a device level works as intended, > > > > > then I would expect this to be a pci core issue, which might actually > > > > > be not fixable there. But if it's not, then we would have to put > > > > > something like that inside the runpm documentation to tell drivers > > > > > they have to do something about it. > > > > >lspci -vvxxxx > > > > > But again, for me it just sounds like the negotiation on the device > > > > > level fails or something inside pci core messes it up. > > > > > > > > To me it sounds like the PMU script messed something up, and the PCI > > > > core has no way to know what that was or how to fix it. > > > > > > > > > > sure, I am mainly wondering why it doesn't work after we power cycled > > > the GPU and the host bridge controller, because no matter what the > > > state was before, we have to reprobe instead of relying on a known > > > state, no? > > > > > > > > > > > > Signed-off-by: Karol Herbst <kherbst at redhat.com> > > > > > > > > > Reviewed-by: Lyude Paul <lyude at redhat.com> > > > > > > > > > --- > > > > > > > > > drm/nouveau/include/nvkm/subdev/pci.h | 5 +++-- > > > > > > > > > drm/nouveau/nvkm/subdev/pci/base.c | 9 +++++++-- > > > > > > > > > drm/nouveau/nvkm/subdev/pci/pcie.c | 24 ++++++++++++++++++++---- > > > > > > > > > drm/nouveau/nvkm/subdev/pci/priv.h | 2 ++ > > > > > > > > > 4 files changed, 32 insertions(+), 8 deletions(-) > > > > > > > > > > > > > > > > > > diff --git a/drm/nouveau/include/nvkm/subdev/pci.h b/drm/nouveau/include/nvkm/subdev/pci.h > > > > > > > > > index 1fdf3098..b23793a2 100644 > > > > > > > > > --- a/drm/nouveau/include/nvkm/subdev/pci.h > > > > > > > > > +++ b/drm/nouveau/include/nvkm/subdev/pci.h > > > > > > > > > @@ -26,8 +26,9 @@ struct nvkm_pci { > > > > > > > > > } agp; > > > > > > > > > > > > > > > > > > struct { > > > > > > > > > - enum nvkm_pcie_speed speed; > > > > > > > > > - u8 width; > > > > > > > > > + enum nvkm_pcie_speed cur_speed; > > > > > > > > > + enum nvkm_pcie_speed def_speed; > > > > > > > > > + u8 cur_width; > > > > > > > > > } pcie; > > > > > > > > > > > > > > > > > > bool msi; > > > > > > > > > diff --git a/drm/nouveau/nvkm/subdev/pci/base.c b/drm/nouveau/nvkm/subdev/pci/base.c > > > > > > > > > index ee2431a7..d9fb5a83 100644 > > > > > > > > > --- a/drm/nouveau/nvkm/subdev/pci/base.c > > > > > > > > > +++ b/drm/nouveau/nvkm/subdev/pci/base.c > > > > > > > > > @@ -90,6 +90,8 @@ nvkm_pci_fini(struct nvkm_subdev *subdev, bool suspend) > > > > > > > > > > > > > > > > > > if (pci->agp.bridge) > > > > > > > > > nvkm_agp_fini(pci); > > > > > > > > > + else if (pci_is_pcie(pci->pdev)) > > > > > > > > > + nvkm_pcie_fini(pci); > > > > > > > > > > > > > > > > > > return 0; > > > > > > > > > } > > > > > > > > > @@ -100,6 +102,8 @@ nvkm_pci_preinit(struct nvkm_subdev *subdev) > > > > > > > > > struct nvkm_pci *pci = nvkm_pci(subdev); > > > > > > > > > if (pci->agp.bridge) > > > > > > > > > nvkm_agp_preinit(pci); > > > > > > > > > + else if (pci_is_pcie(pci->pdev)) > > > > > > > > > + nvkm_pcie_preinit(pci); > > > > > > > > > return 0; > > > > > > > > > } > > > > > > > > > > > > > > > > > > @@ -193,8 +197,9 @@ nvkm_pci_new_(const struct nvkm_pci_func *func, struct nvkm_device *device, > > > > > > > > > pci->func = func; > > > > > > > > > pci->pdev = device->func->pci(device)->pdev; > > > > > > > > > pci->irq = -1; > > > > > > > > > - pci->pcie.speed = -1; > > > > > > > > > - pci->pcie.width = -1; > > > > > > > > > + pci->pcie.cur_speed = -1; > > > > > > > > > + pci->pcie.def_speed = -1; > > > > > > > > > + pci->pcie.cur_width = -1; > > > > > > > > > > > > > > > > > > if (device->type == NVKM_DEVICE_AGP) > > > > > > > > > nvkm_agp_ctor(pci); > > > > > > > > > diff --git a/drm/nouveau/nvkm/subdev/pci/pcie.c b/drm/nouveau/nvkm/subdev/pci/pcie.c > > > > > > > > > index 70ccbe0d..731dd30e 100644 > > > > > > > > > --- a/drm/nouveau/nvkm/subdev/pci/pcie.c > > > > > > > > > +++ b/drm/nouveau/nvkm/subdev/pci/pcie.c > > > > > > > > > @@ -85,6 +85,13 @@ nvkm_pcie_oneinit(struct nvkm_pci *pci) > > > > > > > > > return 0; > > > > > > > > > } > > > > > > > > > > > > > > > > > > +int > > > > > > > > > +nvkm_pcie_preinit(struct nvkm_pci *pci) > > > > > > > > > +{ > > > > > > > > > + pci->pcie.def_speed = nvkm_pcie_get_speed(pci); > > > > > > > > > + return 0; > > > > > > > > > +} > > > > > > > > > + > > > > > > > > > int > > > > > > > > > nvkm_pcie_init(struct nvkm_pci *pci) > > > > > > > > > { > > > > > > > > > @@ -105,12 +112,21 @@ nvkm_pcie_init(struct nvkm_pci *pci) > > > > > > > > > if (pci->func->pcie.init) > > > > > > > > > pci->func->pcie.init(pci); > > > > > > > > > > > > > > > > > > - if (pci->pcie.speed != -1) > > > > > > > > > - nvkm_pcie_set_link(pci, pci->pcie.speed, pci->pcie.width); > > > > > > > > > + if (pci->pcie.cur_speed != -1) > > > > > > > > > + nvkm_pcie_set_link(pci, pci->pcie.cur_speed, > > > > > > > > > + pci->pcie.cur_width); > > > > > > > > > > > > > > > > > > return 0; > > > > > > > > > } > > > > > > > > > > > > > > > > > > +int > > > > > > > > > +nvkm_pcie_fini(struct nvkm_pci *pci) > > > > > > > > > +{ > > > > > > > > > + if (!IS_ERR_VALUE(pci->pcie.def_speed)) > > > > > > > > > + return nvkm_pcie_set_link(pci, pci->pcie.def_speed, 16); > > > > > > > > > + return 0; > > > > > > > > > +} > > > > > > > > > + > > > > > > > > > int > > > > > > > > > nvkm_pcie_set_link(struct nvkm_pci *pci, enum nvkm_pcie_speed speed, u8 width) > > > > > > > > > { > > > > > > > > > @@ -146,8 +162,8 @@ nvkm_pcie_set_link(struct nvkm_pci *pci, enum nvkm_pcie_speed speed, u8 width) > > > > > > > > > speed = max_speed; > > > > > > > > > } > > > > > > > > > > > > > > > > > > - pci->pcie.speed = speed; > > > > > > > > > - pci->pcie.width = width; > > > > > > > > > + pci->pcie.cur_speed = speed; > > > > > > > > > + pci->pcie.cur_width = width; > > > > > > > > > > > > > > > > > > if (speed == cur_speed) { > > > > > > > > > nvkm_debug(subdev, "requested matches current speed\n"); > > > > > > > > > diff --git a/drm/nouveau/nvkm/subdev/pci/priv.h b/drm/nouveau/nvkm/subdev/pci/priv.h > > > > > > > > > index a0d4c007..e7744671 100644 > > > > > > > > > --- a/drm/nouveau/nvkm/subdev/pci/priv.h > > > > > > > > > +++ b/drm/nouveau/nvkm/subdev/pci/priv.h > > > > > > > > > @@ -60,5 +60,7 @@ enum nvkm_pcie_speed gk104_pcie_max_speed(struct nvkm_pci *); > > > > > > > > > int gk104_pcie_version_supported(struct nvkm_pci *); > > > > > > > > > > > > > > > > > > int nvkm_pcie_oneinit(struct nvkm_pci *); > > > > > > > > > +int nvkm_pcie_preinit(struct nvkm_pci *); > > > > > > > > > int nvkm_pcie_init(struct nvkm_pci *); > > > > > > > > > +int nvkm_pcie_fini(struct nvkm_pci *); > > > > > > > > > #endif > > > > > > > > > -- > > > > > > > > > 2.21.0 > > > > > > > > >
Bjorn Helgaas
2019-Jun-03 18:10 UTC
[Nouveau] [PATCH v2 4/4] pci: save the boot pcie link speed and restore it on fini
On Mon, Jun 03, 2019 at 03:18:56PM +0200, Karol Herbst wrote:> @bjorn: any further ideas? Otherwise I'd like to just go ahead and fix > this issue inside Nouveau and leave it there until we have a better > understanding or non Nouveau cases of this issue.Nope, I have no more ideas.> On Tue, May 21, 2019 at 7:48 PM Karol Herbst <kherbst at redhat.com> wrote: > > > > doing the same on the bridge controller with my workarounds applied: > > > > please note some differences: > > LnkSta: Speed 8GT/s (ok) vs Speed 2.5GT/s (downgraded) > > SltSta: PresDet+ vs PresDet- > > LnkSta2: Equalization stuff > > Virtual channel: NegoPending- vs NegoPending+ > > > > both times I executed lspci while the GPU was still suspended. > > > > 00:01.0 PCI bridge: Intel Corporation Xeon E3-1200 v5/E3-1500 v5/6th > > Gen Core Processor PCIe Controller (x16) (rev 05) (prog-if 00 [Normal > > decode]) > > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- > > ParErr- Stepping- SERR- FastB2B- DisINTx- > > Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- > > <TAbort- <MAbort- >SERR- <PERR- INTx- > > Latency: 0 > > Interrupt: pin A routed to IRQ 16 > > Bus: primary=00, secondary=01, subordinate=01, sec-latency=0 > > I/O behind bridge: 0000e000-0000efff [size=4K] > > Memory behind bridge: ec000000-ed0fffff [size=17M] > > Prefetchable memory behind bridge: > > 00000000c0000000-00000000d1ffffff [size=288M] > > Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- > > <TAbort- <MAbort+ <SERR- <PERR- > > BridgeCtl: Parity- SERR- NoISA- VGA- VGA16+ MAbort- >Reset- FastB2B- > > PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- > > Capabilities: [88] Subsystem: Dell Device 07be > > Capabilities: [80] Power Management version 3 > > Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA > > PME(D0+,D1-,D2-,D3hot+,D3cold+) > > Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME- > > Capabilities: [90] MSI: Enable- Count=1/1 Maskable- 64bit- > > Address: 00000000 Data: 0000 > > Capabilities: [a0] Express (v2) Root Port (Slot+), MSI 00 > > DevCap: MaxPayload 256 bytes, PhantFunc 0 > > ExtTag- RBE+ > > DevCtl: CorrErr- NonFatalErr- FatalErr- UnsupReq- > > RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop- > > MaxPayload 256 bytes, MaxReadReq 128 bytes > > DevSta: CorrErr- NonFatalErr- FatalErr- UnsupReq- > > AuxPwr- TransPend- > > LnkCap: Port #2, Speed 8GT/s, Width x16, ASPM L0s L1, > > Exit Latency L0s <256ns, L1 <8us > > ClockPM- Surprise- LLActRep- BwNot+ ASPMOptComp+ > > LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- CommClk+ > > ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt- > > LnkSta: Speed 8GT/s (ok), Width x16 (ok) > > TrErr- Train- SlotClk+ DLActive- BWMgmt+ ABWMgmt+ > > SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- > > HotPlug- Surprise- > > Slot #1, PowerLimit 75.000W; Interlock- NoCompl+ > > SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- > > CmdCplt- HPIrq- LinkChg- > > Control: AttnInd Unknown, PwrInd Unknown, > > Power- Interlock- > > SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- > > PresDet+ Interlock- > > Changed: MRL- PresDet+ LinkState- > > RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- > > PMEIntEna- CRSVisible- > > RootCap: CRSVisible- > > RootSta: PME ReqID 0000, PMEStatus- PMEPending- > > DevCap2: Completion Timeout: Not Supported, > > TimeoutDis-, LTR+, OBFF Via WAKE# ARIFwd- > > AtomicOpsCap: Routing- 32bit+ 64bit+ 128bitCAS+ > > DevCtl2: Completion Timeout: 50us to 50ms, > > TimeoutDis-, LTR+, OBFF Via WAKE# ARIFwd- > > AtomicOpsCtl: ReqEn- EgressBlck- > > LnkCtl2: Target Link Speed: 8GT/s, EnterCompliance- SpeedDis- > > Transmit Margin: Normal Operating Range, > > EnterModifiedCompliance- ComplianceSOS- > > Compliance De-emphasis: -6dB > > LnkSta2: Current De-emphasis Level: -6dB, > > EqualizationComplete+, EqualizationPhase1+ > > EqualizationPhase2+, EqualizationPhase3+, > > LinkEqualizationRequest- > > Capabilities: [100 v1] Virtual Channel > > Caps: LPEVC=0 RefClk=100ns PATEntryBits=1 > > Arb: Fixed- WRR32- WRR64- WRR128- > > Ctrl: ArbSelect=Fixed > > Status: InProgress- > > VC0: Caps: PATOffset=00 MaxTimeSlots=1 RejSnoopTrans- > > Arb: Fixed+ WRR32- WRR64- WRR128- TWRR128- WRR256- > > Ctrl: Enable+ ID=0 ArbSelect=Fixed TC/VC=ff > > Status: NegoPending- InProgress- > > Capabilities: [140 v1] Root Complex Link > > Desc: PortNumber=02 ComponentID=01 EltType=Config > > Link0: Desc: TargetPort=00 TargetComponent=01 > > AssocRCRB- LinkType=MemMapped LinkValid+ > > Addr: 00000000fed19000 > > Capabilities: [d94 v1] Secondary PCI Express <?> > > Kernel driver in use: pcieport > > 00: 86 80 01 19 07 00 10 00 05 00 04 06 00 00 81 00 > > 10: 00 00 00 00 00 00 00 00 00 01 01 00 e0 e0 00 20 > > 20: 00 ec 00 ed 01 c0 f1 d1 00 00 00 00 00 00 00 00 > > 30: 00 00 00 00 88 00 00 00 00 00 00 00 ff 01 10 00 > > 40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 > > 50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 > > 60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 > > 70: 00 00 00 00 00 00 00 00 00 62 17 00 00 00 00 0a > > 80: 01 90 03 c8 08 00 00 00 0d 80 00 00 28 10 be 07 > > 90: 05 a0 00 00 00 00 00 00 00 00 00 00 00 00 00 00 > > a0: 10 00 42 01 01 80 00 00 20 00 00 00 03 ad 61 02 > > b0: 40 00 03 d1 80 25 0c 00 00 00 48 00 00 00 00 00 > > c0: 00 00 00 00 80 0b 08 00 00 64 00 00 0e 00 00 00 > > d0: 43 00 1e 00 00 00 00 00 00 00 00 00 00 00 00 00 > > e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 > > f0: 00 00 00 84 4e 01 01 20 00 00 00 00 e0 00 10 00 > > > > On Tue, May 21, 2019 at 7:35 PM Karol Herbst <kherbst at redhat.com> wrote: > > > > > > was able to get the lspci prints via ssh. Machine rebooted > > > automatically each time though. > > > > > > relevant dmesg: > > > kernel: nouveau 0000:01:00.0: Refused to change power state, currently in D3 > > > kernel: nouveau 0000:01:00.0: Refused to change power state, currently in D3 > > > kernel: nouveau 0000:01:00.0: Refused to change power state, currently in D3 > > > kernel: nouveau 0000:01:00.0: tmr: stalled at ffffffffffffffff > > > > > > (last one is a 64 bit mmio read to get the on GPU timer value) > > > > > > # lspci -vvxxx -s 0:01.00 > > > 00:01.0 PCI bridge: Intel Corporation Xeon E3-1200 v5/E3-1500 v5/6th > > > Gen Core Processor PCIe Controller (x16) (rev 05) (prog-if 00 [Normal > > > decode]) > > > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- > > > ParErr- Stepping- SERR- FastB2B- DisINTx- > > > Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- > > > <TAbort- <MAbort- >SERR- <PERR- INTx- > > > Latency: 0 > > > Interrupt: pin A routed to IRQ 16 > > > Bus: primary=00, secondary=01, subordinate=01, sec-latency=0 > > > I/O behind bridge: 0000e000-0000efff [size=4K] > > > Memory behind bridge: ec000000-ed0fffff [size=17M] > > > Prefetchable memory behind bridge: > > > 00000000c0000000-00000000d1ffffff [size=288M] > > > Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- > > > <TAbort- <MAbort+ <SERR- <PERR- > > > BridgeCtl: Parity- SERR- NoISA- VGA- VGA16+ MAbort- >Reset- FastB2B- > > > PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- > > > Capabilities: [88] Subsystem: Dell Device 07be > > > Capabilities: [80] Power Management version 3 > > > Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA > > > PME(D0+,D1-,D2-,D3hot+,D3cold+) > > > Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME- > > > Capabilities: [90] MSI: Enable- Count=1/1 Maskable- 64bit- > > > Address: 00000000 Data: 0000 > > > Capabilities: [a0] Express (v2) Root Port (Slot+), MSI 00 > > > DevCap: MaxPayload 256 bytes, PhantFunc 0 > > > ExtTag- RBE+ > > > DevCtl: CorrErr- NonFatalErr- FatalErr- UnsupReq- > > > RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop- > > > MaxPayload 256 bytes, MaxReadReq 128 bytes > > > DevSta: CorrErr- NonFatalErr- FatalErr- UnsupReq- > > > AuxPwr- TransPend- > > > LnkCap: Port #2, Speed 8GT/s, Width x16, ASPM L0s L1, > > > Exit Latency L0s <256ns, L1 <8us > > > ClockPM- Surprise- LLActRep- BwNot+ ASPMOptComp+ > > > LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- CommClk+ > > > ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt- > > > LnkSta: Speed 2.5GT/s (downgraded), Width x16 (ok) > > > TrErr- Train- SlotClk+ DLActive- BWMgmt+ ABWMgmt+ > > > SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- > > > HotPlug- Surprise- > > > Slot #1, PowerLimit 75.000W; Interlock- NoCompl+ > > > SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- > > > HPIrq- LinkChg- > > > Control: AttnInd Unknown, PwrInd Unknown, > > > Power- Interlock- > > > SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- > > > PresDet- Interlock- > > > Changed: MRL- PresDet+ LinkState- > > > RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- > > > PMEIntEna- CRSVisible- > > > RootCap: CRSVisible- > > > RootSta: PME ReqID 0000, PMEStatus- PMEPending- > > > DevCap2: Completion Timeout: Not Supported, > > > TimeoutDis-, LTR+, OBFF Via WAKE# ARIFwd- > > > AtomicOpsCap: Routing- 32bit+ 64bit+ 128bitCAS+ > > > DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-, > > > LTR+, OBFF Via WAKE# ARIFwd- > > > AtomicOpsCtl: ReqEn- EgressBlck- > > > LnkCtl2: Target Link Speed: 8GT/s, EnterCompliance- SpeedDis- > > > Transmit Margin: Normal Operating Range, > > > EnterModifiedCompliance- ComplianceSOS- > > > Compliance De-emphasis: -6dB > > > LnkSta2: Current De-emphasis Level: -6dB, > > > EqualizationComplete-, EqualizationPhase1- > > > EqualizationPhase2-, EqualizationPhase3-, > > > LinkEqualizationRequest- > > > Capabilities: [100 v1] Virtual Channel > > > Caps: LPEVC=0 RefClk=100ns PATEntryBits=1 > > > Arb: Fixed- WRR32- WRR64- WRR128- > > > Ctrl: ArbSelect=Fixed > > > Status: InProgress- > > > VC0: Caps: PATOffset=00 MaxTimeSlots=1 RejSnoopTrans- > > > Arb: Fixed+ WRR32- WRR64- WRR128- TWRR128- WRR256- > > > Ctrl: Enable+ ID=0 ArbSelect=Fixed TC/VC=ff > > > Status: NegoPending+ InProgress- > > > Capabilities: [140 v1] Root Complex Link > > > Desc: PortNumber=02 ComponentID=01 EltType=Config > > > Link0: Desc: TargetPort=00 TargetComponent=01 > > > AssocRCRB- LinkType=MemMapped LinkValid+ > > > Addr: 00000000fed19000 > > > Capabilities: [d94 v1] Secondary PCI Express <?> > > > Kernel driver in use: pcieport > > > 00: 86 80 01 19 07 00 10 00 05 00 04 06 00 00 81 00 > > > 10: 00 00 00 00 00 00 00 00 00 01 01 00 e0 e0 00 20 > > > 20: 00 ec 00 ed 01 c0 f1 d1 00 00 00 00 00 00 00 00 > > > 30: 00 00 00 00 88 00 00 00 00 00 00 00 ff 01 10 00 > > > 40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 > > > 50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 > > > 60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 > > > 70: 00 00 00 00 00 00 00 00 00 62 17 00 00 00 00 0a > > > 80: 01 90 03 c8 08 00 00 00 0d 80 00 00 28 10 be 07 > > > 90: 05 a0 00 00 00 00 00 00 00 00 00 00 00 00 00 00 > > > a0: 10 00 42 01 01 80 00 00 20 00 00 00 03 ad 61 02 > > > b0: 40 00 01 d1 80 25 0c 00 00 00 08 00 00 00 00 00 > > > c0: 00 00 00 00 80 0b 08 00 00 64 00 00 0e 00 00 00 > > > d0: 43 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 > > > e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 > > > f0: 00 40 01 00 4e 01 01 22 00 00 00 00 e0 00 10 00 > > > > > > lspci -vvxxx -s 1:00.00 > > > 01:00.0 3D controller: NVIDIA Corporation GP107M [GeForce GTX 1050 > > > Mobile] (rev ff) (prog-if ff) > > > !!! Unknown header type 7f > > > Kernel driver in use: nouveau > > > Kernel modules: nouveau > > > 00: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff > > > 10: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff > > > 20: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff > > > 30: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff > > > 40: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff > > > 50: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff > > > 60: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff > > > 70: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff > > > 80: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff > > > 90: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff > > > a0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff > > > b0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff > > > c0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff > > > d0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff > > > e0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff > > > f0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff > > > > > > On Tue, May 21, 2019 at 4:30 PM Karol Herbst <kherbst at redhat.com> wrote: > > > > > > > > On Tue, May 21, 2019 at 4:13 PM Bjorn Helgaas <helgaas at kernel.org> wrote: > > > > > > > > > > On Tue, May 21, 2019 at 03:28:48PM +0200, Karol Herbst wrote: > > > > > > On Tue, May 21, 2019 at 3:11 PM Bjorn Helgaas <helgaas at kernel.org> wrote: > > > > > > > On Tue, May 21, 2019 at 12:30:38AM +0200, Karol Herbst wrote: > > > > > > > > On Mon, May 20, 2019 at 11:20 PM Bjorn Helgaas <helgaas at kernel.org> wrote: > > > > > > > > > On Tue, May 07, 2019 at 10:12:45PM +0200, Karol Herbst wrote: > > > > > > > > > > Apperantly things go south if we suspend the device with a different PCIE > > > > > > > > > > link speed set than it got booted with. Fixes runtime suspend on my gp107. > > > > > > > > > > > > > > > > > > > > This all looks like some bug inside the pci subsystem and I would prefer a > > > > > > > > > > fix there instead of nouveau, but maybe there is no real nice way of doing > > > > > > > > > > that outside of drivers? > > > > > > > > > > > > > > > > > > I agree it would be nice to fix this in the PCI core if that's > > > > > > > > > feasible. > > > > > > > > > > > > > > > > > > It looks like this driver changes the PCIe link speed using some > > > > > > > > > device-specific mechanism. When we suspend, we put the device in > > > > > > > > > D3cold, so it loses all its state. When we resume, the link probably > > > > > > > > > comes up at the boot speed because nothing did that device-specific > > > > > > > > > magic to change it, so you probably end up with the link being slow > > > > > > > > > but the driver thinking it's configured to be fast, and maybe that > > > > > > > > > combination doesn't work. > > > > > > > > > > > > > > > > > > If it requires something device-specific to change that link speed, I > > > > > > > > > don't know how to put that in the PCI core. But maybe I'm missing > > > > > > > > > something? > > > > > > > > > > > > > > > > > > Per the PCIe spec (r4.0, sec 1.2): > > > > > > > > > > > > > > > > > > Initialization – During hardware initialization, each PCI Express > > > > > > > > > Link is set up following a negotiation of Lane widths and frequency > > > > > > > > > of operation by the two agents at each end of the Link. No firmware > > > > > > > > > or operating system software is involved. > > > > > > > > > > > > > > > > > > I have been assuming that this means device-specific link speed > > > > > > > > > management is out of spec, but it seems pretty common that devices > > > > > > > > > don't come up by themselves at the fastest possible link speed. So > > > > > > > > > maybe the spec just intends that devices can operate at *some* valid > > > > > > > > > speed. > > > > > > > > > > > > > > > > I would expect that devices kind of have to figure out what they can > > > > > > > > operate on and the operating system kind of just checks what the > > > > > > > > current state is and doesn't try to "restore" the old state or > > > > > > > > something? > > > > > > > > > > > > > > The devices at each end of the link negotiate the width and speed of > > > > > > > the link. This is done directly by the hardware without any help from > > > > > > > the OS. > > > > > > > > > > > > > > The OS can read the current link state (Current Link Speed and > > > > > > > Negotiated Link Width, both in the Link Status register). The OS has > > > > > > > very little control over that state. It can't directly restore the > > > > > > > state because the hardware has to negotiate a width & speed that > > > > > > > result in reliable operation. > > > > > > > > > > > > > > > We don't do anything in the driver after the device was suspended. And > > > > > > > > the 0x88000 is a mirror of the PCI config space, but we also got some > > > > > > > > PCIe stuff at 0x8c000 which is used by newer GPUs for gen3 stuff > > > > > > > > essentially. I have no idea how much of this is part of the actual pci > > > > > > > > standard and how much is driver specific. But the driver also wants to > > > > > > > > have some control over the link speed as it's tight to performance > > > > > > > > states on GPU. > > > > > > > > > > > > > > As far as I'm aware, there is no generic PCIe way for the OS to > > > > > > > influence the link width or speed. If the GPU driver needs to do > > > > > > > that, it would be via some device-specific mechanism. > > > > > > > > > > > > > > > The big issue here is just, that the GPU boots with 8.0, some on-gpu > > > > > > > > init mechanism decreases it to 2.5. If we suspend, the GPU or at least > > > > > > > > the communication with the controller is broken. But if we set it to > > > > > > > > the boot speed, resuming the GPU just works. So my assumption was, > > > > > > > > that _something_ (might it be the controller or the pci subsystem) > > > > > > > > tries to force to operate on an invalid link speed and because the > > > > > > > > bridge controller is actually powered down as well (as all children > > > > > > > > are in D3cold) I could imagine that something in the pci subsystem > > > > > > > > actually restores the state which lets the controller fail to > > > > > > > > establish communication again? > > > > > > > > > > > > > > 1) At boot-time, the Port and the GPU hardware negotiate 8.0 GT/s > > > > > > > without OS/driver intervention. > > > > > > > > > > > > > > 2) Some mechanism reduces link speed to 2.5 GT/s. This probably > > > > > > > requires driver intervention or at least some ACPI method. > > > > > > > > > > > > there is no driver intervention and Nouveau doesn't care at all. It's > > > > > > all done on the GPU. We just upload a script and some firmware on to > > > > > > the GPU. The script runs then on the PMU inside the GPU and this > > > > > > script also causes changing the PCIe link settings. But from a Nouveau > > > > > > point of view we don't care about the link before or after that script > > > > > > was invoked. Also there is no ACPI method involved. > > > > > > > > > > > > But if there is something we should notify pci core about, maybe > > > > > > that's something we have to do then? > > > > > > > > > > I don't think there's anything the PCI core could do with that > > > > > information anyway. The PCI core doesn't care at all about the link > > > > > speed, and it really can't influence it directly. > > > > > > > > > > > > 3) Suspend puts GPU into D3cold (powered off). > > > > > > > > > > > > > > 4) Resume restores GPU to D0, and the Port and GPU hardware again > > > > > > > negotiate 8.0 GT/s without OS/driver intervention, just like at > > > > > > > initial boot. > > > > > > > > > > > > No, that negotiation fails apparently as any attempt to read anything > > > > > > from the device just fails inside pci core. Or something goes wrong > > > > > > when resuming the bridge controller. > > > > > > > > > > I'm surprised the negotiation would fail even after a power cycle of > > > > > the device. But if you can avoid the issue by running another script > > > > > on the PMU before suspend, that's probably what you'll have to do. > > > > > > > > > > > > > there is none as far as we know. Or at least nothing inside the vbios. > > > > We still have to get signed PMU firmware images from Nvidia for full > > > > support, but this still would be a hacky issue as we would depend on > > > > those then (and without having those in redistributable form, there > > > > isn't much we can do about except fixing it on the kernel side). > > > > > > > > > > > 5) Now the driver thinks the GPU is at 2.5 GT/s but it's actually at > > > > > > > 8.0 GT/s. > > > > > > > > > > > > what is actually meant by "driver" here? The pci subsystem or Nouveau? > > > > > > > > > > I was thinking Nouveau because the PCI core doesn't care about the > > > > > link speed. > > > > > > > > > > > > Without knowing more about the transition to 2.5 GT/s, I can't guess > > > > > > > why the GPU wouldn't work after resume. From a PCIe point of view, > > > > > > > the link is supposed to work and the device should be reachable > > > > > > > independent of the link speed. But maybe there's some weird > > > > > > > dependency between the GPU and the driver here. > > > > > > > > > > > > but the device isn't reachable at all, not even from the pci > > > > > > subsystem. All reads fail/return a default error value (0xffffffff). > > > > > > > > > > Are these PCI config reads that return 0xffffffff? Or MMIO reads? > > > > > "lspci -vvxxxx" of the bridge and the GPU might have a clue about > > > > > whether a PCI error occurred. > > > > > > > > > > > > > that's kind of problematic as it might just lock up my machine... but > > > > let me try that. > > > > > > > > > > > It sounds like things work if you return to 8.0 GT/s before suspend, > > > > > > > things work. That would make sense to me because then the driver's > > > > > > > idea of the link state after resume would match the actual state. > > > > > > > > > > > > depends on what is meant by the driver here. Inside Nouveau we don't > > > > > > care one bit about the current link speed, so I assume you mean > > > > > > something inside the pci core code? > > > > > > > > > > > > > But I don't see a way to deal with this in the PCI core. The PCI core > > > > > > > does save and restore most of the architected config space around > > > > > > > suspend/resume, but since this appears to be a device-specific thing, > > > > > > > the PCI core would have no idea how to save/restore it. > > > > > > > > > > > > if we assume that the negotiation on a device level works as intended, > > > > > > then I would expect this to be a pci core issue, which might actually > > > > > > be not fixable there. But if it's not, then we would have to put > > > > > > something like that inside the runpm documentation to tell drivers > > > > > > they have to do something about it. > > > > > >lspci -vvxxxx > > > > > > But again, for me it just sounds like the negotiation on the device > > > > > > level fails or something inside pci core messes it up. > > > > > > > > > > To me it sounds like the PMU script messed something up, and the PCI > > > > > core has no way to know what that was or how to fix it. > > > > > > > > > > > > > sure, I am mainly wondering why it doesn't work after we power cycled > > > > the GPU and the host bridge controller, because no matter what the > > > > state was before, we have to reprobe instead of relying on a known > > > > state, no? > > > > > > > > > > > > > > Signed-off-by: Karol Herbst <kherbst at redhat.com> > > > > > > > > > > Reviewed-by: Lyude Paul <lyude at redhat.com> > > > > > > > > > > --- > > > > > > > > > > drm/nouveau/include/nvkm/subdev/pci.h | 5 +++-- > > > > > > > > > > drm/nouveau/nvkm/subdev/pci/base.c | 9 +++++++-- > > > > > > > > > > drm/nouveau/nvkm/subdev/pci/pcie.c | 24 ++++++++++++++++++++---- > > > > > > > > > > drm/nouveau/nvkm/subdev/pci/priv.h | 2 ++ > > > > > > > > > > 4 files changed, 32 insertions(+), 8 deletions(-) > > > > > > > > > > > > > > > > > > > > diff --git a/drm/nouveau/include/nvkm/subdev/pci.h b/drm/nouveau/include/nvkm/subdev/pci.h > > > > > > > > > > index 1fdf3098..b23793a2 100644 > > > > > > > > > > --- a/drm/nouveau/include/nvkm/subdev/pci.h > > > > > > > > > > +++ b/drm/nouveau/include/nvkm/subdev/pci.h > > > > > > > > > > @@ -26,8 +26,9 @@ struct nvkm_pci { > > > > > > > > > > } agp; > > > > > > > > > > > > > > > > > > > > struct { > > > > > > > > > > - enum nvkm_pcie_speed speed; > > > > > > > > > > - u8 width; > > > > > > > > > > + enum nvkm_pcie_speed cur_speed; > > > > > > > > > > + enum nvkm_pcie_speed def_speed; > > > > > > > > > > + u8 cur_width; > > > > > > > > > > } pcie; > > > > > > > > > > > > > > > > > > > > bool msi; > > > > > > > > > > diff --git a/drm/nouveau/nvkm/subdev/pci/base.c b/drm/nouveau/nvkm/subdev/pci/base.c > > > > > > > > > > index ee2431a7..d9fb5a83 100644 > > > > > > > > > > --- a/drm/nouveau/nvkm/subdev/pci/base.c > > > > > > > > > > +++ b/drm/nouveau/nvkm/subdev/pci/base.c > > > > > > > > > > @@ -90,6 +90,8 @@ nvkm_pci_fini(struct nvkm_subdev *subdev, bool suspend) > > > > > > > > > > > > > > > > > > > > if (pci->agp.bridge) > > > > > > > > > > nvkm_agp_fini(pci); > > > > > > > > > > + else if (pci_is_pcie(pci->pdev)) > > > > > > > > > > + nvkm_pcie_fini(pci); > > > > > > > > > > > > > > > > > > > > return 0; > > > > > > > > > > } > > > > > > > > > > @@ -100,6 +102,8 @@ nvkm_pci_preinit(struct nvkm_subdev *subdev) > > > > > > > > > > struct nvkm_pci *pci = nvkm_pci(subdev); > > > > > > > > > > if (pci->agp.bridge) > > > > > > > > > > nvkm_agp_preinit(pci); > > > > > > > > > > + else if (pci_is_pcie(pci->pdev)) > > > > > > > > > > + nvkm_pcie_preinit(pci); > > > > > > > > > > return 0; > > > > > > > > > > } > > > > > > > > > > > > > > > > > > > > @@ -193,8 +197,9 @@ nvkm_pci_new_(const struct nvkm_pci_func *func, struct nvkm_device *device, > > > > > > > > > > pci->func = func; > > > > > > > > > > pci->pdev = device->func->pci(device)->pdev; > > > > > > > > > > pci->irq = -1; > > > > > > > > > > - pci->pcie.speed = -1; > > > > > > > > > > - pci->pcie.width = -1; > > > > > > > > > > + pci->pcie.cur_speed = -1; > > > > > > > > > > + pci->pcie.def_speed = -1; > > > > > > > > > > + pci->pcie.cur_width = -1; > > > > > > > > > > > > > > > > > > > > if (device->type == NVKM_DEVICE_AGP) > > > > > > > > > > nvkm_agp_ctor(pci); > > > > > > > > > > diff --git a/drm/nouveau/nvkm/subdev/pci/pcie.c b/drm/nouveau/nvkm/subdev/pci/pcie.c > > > > > > > > > > index 70ccbe0d..731dd30e 100644 > > > > > > > > > > --- a/drm/nouveau/nvkm/subdev/pci/pcie.c > > > > > > > > > > +++ b/drm/nouveau/nvkm/subdev/pci/pcie.c > > > > > > > > > > @@ -85,6 +85,13 @@ nvkm_pcie_oneinit(struct nvkm_pci *pci) > > > > > > > > > > return 0; > > > > > > > > > > } > > > > > > > > > > > > > > > > > > > > +int > > > > > > > > > > +nvkm_pcie_preinit(struct nvkm_pci *pci) > > > > > > > > > > +{ > > > > > > > > > > + pci->pcie.def_speed = nvkm_pcie_get_speed(pci); > > > > > > > > > > + return 0; > > > > > > > > > > +} > > > > > > > > > > + > > > > > > > > > > int > > > > > > > > > > nvkm_pcie_init(struct nvkm_pci *pci) > > > > > > > > > > { > > > > > > > > > > @@ -105,12 +112,21 @@ nvkm_pcie_init(struct nvkm_pci *pci) > > > > > > > > > > if (pci->func->pcie.init) > > > > > > > > > > pci->func->pcie.init(pci); > > > > > > > > > > > > > > > > > > > > - if (pci->pcie.speed != -1) > > > > > > > > > > - nvkm_pcie_set_link(pci, pci->pcie.speed, pci->pcie.width); > > > > > > > > > > + if (pci->pcie.cur_speed != -1) > > > > > > > > > > + nvkm_pcie_set_link(pci, pci->pcie.cur_speed, > > > > > > > > > > + pci->pcie.cur_width); > > > > > > > > > > > > > > > > > > > > return 0; > > > > > > > > > > } > > > > > > > > > > > > > > > > > > > > +int > > > > > > > > > > +nvkm_pcie_fini(struct nvkm_pci *pci) > > > > > > > > > > +{ > > > > > > > > > > + if (!IS_ERR_VALUE(pci->pcie.def_speed)) > > > > > > > > > > + return nvkm_pcie_set_link(pci, pci->pcie.def_speed, 16); > > > > > > > > > > + return 0; > > > > > > > > > > +} > > > > > > > > > > + > > > > > > > > > > int > > > > > > > > > > nvkm_pcie_set_link(struct nvkm_pci *pci, enum nvkm_pcie_speed speed, u8 width) > > > > > > > > > > { > > > > > > > > > > @@ -146,8 +162,8 @@ nvkm_pcie_set_link(struct nvkm_pci *pci, enum nvkm_pcie_speed speed, u8 width) > > > > > > > > > > speed = max_speed; > > > > > > > > > > } > > > > > > > > > > > > > > > > > > > > - pci->pcie.speed = speed; > > > > > > > > > > - pci->pcie.width = width; > > > > > > > > > > + pci->pcie.cur_speed = speed; > > > > > > > > > > + pci->pcie.cur_width = width; > > > > > > > > > > > > > > > > > > > > if (speed == cur_speed) { > > > > > > > > > > nvkm_debug(subdev, "requested matches current speed\n"); > > > > > > > > > > diff --git a/drm/nouveau/nvkm/subdev/pci/priv.h b/drm/nouveau/nvkm/subdev/pci/priv.h > > > > > > > > > > index a0d4c007..e7744671 100644 > > > > > > > > > > --- a/drm/nouveau/nvkm/subdev/pci/priv.h > > > > > > > > > > +++ b/drm/nouveau/nvkm/subdev/pci/priv.h > > > > > > > > > > @@ -60,5 +60,7 @@ enum nvkm_pcie_speed gk104_pcie_max_speed(struct nvkm_pci *); > > > > > > > > > > int gk104_pcie_version_supported(struct nvkm_pci *); > > > > > > > > > > > > > > > > > > > > int nvkm_pcie_oneinit(struct nvkm_pci *); > > > > > > > > > > +int nvkm_pcie_preinit(struct nvkm_pci *); > > > > > > > > > > int nvkm_pcie_init(struct nvkm_pci *); > > > > > > > > > > +int nvkm_pcie_fini(struct nvkm_pci *); > > > > > > > > > > #endif > > > > > > > > > > -- > > > > > > > > > > 2.21.0 > > > > > > > > > >
Karol Herbst
2019-Jun-19 12:07 UTC
[Nouveau] [PATCH v2 4/4] pci: save the boot pcie link speed and restore it on fini
Hi Bjorn, I was playing around with some older information again (write into the PCI config to put the card into d3 state). And there is something which made me very curious: If I put the card manually into any other state besides D0 via the 0x64 pci config register, the card just dies and pci core seems to expect this to not happen. pci_raw_set_power_state has this "pci_write_config_word(dev, dev->pm_cap + PCI_PM_CTRL, pmcsr);" call, and reads the value back later, but if the card is already gone, maybe we can't do this for nvidia GPUs? No idea why I didn't played around more with that register, but if the card already dies there then this kind of shows there is indeed an issue on a PCI level, no? On Mon, Jun 3, 2019 at 8:10 PM Bjorn Helgaas <helgaas at kernel.org> wrote:> > On Mon, Jun 03, 2019 at 03:18:56PM +0200, Karol Herbst wrote: > > @bjorn: any further ideas? Otherwise I'd like to just go ahead and fix > > this issue inside Nouveau and leave it there until we have a better > > understanding or non Nouveau cases of this issue. > > Nope, I have no more ideas. > > > On Tue, May 21, 2019 at 7:48 PM Karol Herbst <kherbst at redhat.com> wrote: > > > > > > doing the same on the bridge controller with my workarounds applied: > > > > > > please note some differences: > > > LnkSta: Speed 8GT/s (ok) vs Speed 2.5GT/s (downgraded) > > > SltSta: PresDet+ vs PresDet- > > > LnkSta2: Equalization stuff > > > Virtual channel: NegoPending- vs NegoPending+ > > > > > > both times I executed lspci while the GPU was still suspended. > > > > > > 00:01.0 PCI bridge: Intel Corporation Xeon E3-1200 v5/E3-1500 v5/6th > > > Gen Core Processor PCIe Controller (x16) (rev 05) (prog-if 00 [Normal > > > decode]) > > > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- > > > ParErr- Stepping- SERR- FastB2B- DisINTx- > > > Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- > > > <TAbort- <MAbort- >SERR- <PERR- INTx- > > > Latency: 0 > > > Interrupt: pin A routed to IRQ 16 > > > Bus: primary=00, secondary=01, subordinate=01, sec-latency=0 > > > I/O behind bridge: 0000e000-0000efff [size=4K] > > > Memory behind bridge: ec000000-ed0fffff [size=17M] > > > Prefetchable memory behind bridge: > > > 00000000c0000000-00000000d1ffffff [size=288M] > > > Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- > > > <TAbort- <MAbort+ <SERR- <PERR- > > > BridgeCtl: Parity- SERR- NoISA- VGA- VGA16+ MAbort- >Reset- FastB2B- > > > PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- > > > Capabilities: [88] Subsystem: Dell Device 07be > > > Capabilities: [80] Power Management version 3 > > > Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA > > > PME(D0+,D1-,D2-,D3hot+,D3cold+) > > > Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME- > > > Capabilities: [90] MSI: Enable- Count=1/1 Maskable- 64bit- > > > Address: 00000000 Data: 0000 > > > Capabilities: [a0] Express (v2) Root Port (Slot+), MSI 00 > > > DevCap: MaxPayload 256 bytes, PhantFunc 0 > > > ExtTag- RBE+ > > > DevCtl: CorrErr- NonFatalErr- FatalErr- UnsupReq- > > > RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop- > > > MaxPayload 256 bytes, MaxReadReq 128 bytes > > > DevSta: CorrErr- NonFatalErr- FatalErr- UnsupReq- > > > AuxPwr- TransPend- > > > LnkCap: Port #2, Speed 8GT/s, Width x16, ASPM L0s L1, > > > Exit Latency L0s <256ns, L1 <8us > > > ClockPM- Surprise- LLActRep- BwNot+ ASPMOptComp+ > > > LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- CommClk+ > > > ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt- > > > LnkSta: Speed 8GT/s (ok), Width x16 (ok) > > > TrErr- Train- SlotClk+ DLActive- BWMgmt+ ABWMgmt+ > > > SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- > > > HotPlug- Surprise- > > > Slot #1, PowerLimit 75.000W; Interlock- NoCompl+ > > > SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- > > > CmdCplt- HPIrq- LinkChg- > > > Control: AttnInd Unknown, PwrInd Unknown, > > > Power- Interlock- > > > SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- > > > PresDet+ Interlock- > > > Changed: MRL- PresDet+ LinkState- > > > RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- > > > PMEIntEna- CRSVisible- > > > RootCap: CRSVisible- > > > RootSta: PME ReqID 0000, PMEStatus- PMEPending- > > > DevCap2: Completion Timeout: Not Supported, > > > TimeoutDis-, LTR+, OBFF Via WAKE# ARIFwd- > > > AtomicOpsCap: Routing- 32bit+ 64bit+ 128bitCAS+ > > > DevCtl2: Completion Timeout: 50us to 50ms, > > > TimeoutDis-, LTR+, OBFF Via WAKE# ARIFwd- > > > AtomicOpsCtl: ReqEn- EgressBlck- > > > LnkCtl2: Target Link Speed: 8GT/s, EnterCompliance- SpeedDis- > > > Transmit Margin: Normal Operating Range, > > > EnterModifiedCompliance- ComplianceSOS- > > > Compliance De-emphasis: -6dB > > > LnkSta2: Current De-emphasis Level: -6dB, > > > EqualizationComplete+, EqualizationPhase1+ > > > EqualizationPhase2+, EqualizationPhase3+, > > > LinkEqualizationRequest- > > > Capabilities: [100 v1] Virtual Channel > > > Caps: LPEVC=0 RefClk=100ns PATEntryBits=1 > > > Arb: Fixed- WRR32- WRR64- WRR128- > > > Ctrl: ArbSelect=Fixed > > > Status: InProgress- > > > VC0: Caps: PATOffset=00 MaxTimeSlots=1 RejSnoopTrans- > > > Arb: Fixed+ WRR32- WRR64- WRR128- TWRR128- WRR256- > > > Ctrl: Enable+ ID=0 ArbSelect=Fixed TC/VC=ff > > > Status: NegoPending- InProgress- > > > Capabilities: [140 v1] Root Complex Link > > > Desc: PortNumber=02 ComponentID=01 EltType=Config > > > Link0: Desc: TargetPort=00 TargetComponent=01 > > > AssocRCRB- LinkType=MemMapped LinkValid+ > > > Addr: 00000000fed19000 > > > Capabilities: [d94 v1] Secondary PCI Express <?> > > > Kernel driver in use: pcieport > > > 00: 86 80 01 19 07 00 10 00 05 00 04 06 00 00 81 00 > > > 10: 00 00 00 00 00 00 00 00 00 01 01 00 e0 e0 00 20 > > > 20: 00 ec 00 ed 01 c0 f1 d1 00 00 00 00 00 00 00 00 > > > 30: 00 00 00 00 88 00 00 00 00 00 00 00 ff 01 10 00 > > > 40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 > > > 50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 > > > 60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 > > > 70: 00 00 00 00 00 00 00 00 00 62 17 00 00 00 00 0a > > > 80: 01 90 03 c8 08 00 00 00 0d 80 00 00 28 10 be 07 > > > 90: 05 a0 00 00 00 00 00 00 00 00 00 00 00 00 00 00 > > > a0: 10 00 42 01 01 80 00 00 20 00 00 00 03 ad 61 02 > > > b0: 40 00 03 d1 80 25 0c 00 00 00 48 00 00 00 00 00 > > > c0: 00 00 00 00 80 0b 08 00 00 64 00 00 0e 00 00 00 > > > d0: 43 00 1e 00 00 00 00 00 00 00 00 00 00 00 00 00 > > > e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 > > > f0: 00 00 00 84 4e 01 01 20 00 00 00 00 e0 00 10 00 > > > > > > On Tue, May 21, 2019 at 7:35 PM Karol Herbst <kherbst at redhat.com> wrote: > > > > > > > > was able to get the lspci prints via ssh. Machine rebooted > > > > automatically each time though. > > > > > > > > relevant dmesg: > > > > kernel: nouveau 0000:01:00.0: Refused to change power state, currently in D3 > > > > kernel: nouveau 0000:01:00.0: Refused to change power state, currently in D3 > > > > kernel: nouveau 0000:01:00.0: Refused to change power state, currently in D3 > > > > kernel: nouveau 0000:01:00.0: tmr: stalled at ffffffffffffffff > > > > > > > > (last one is a 64 bit mmio read to get the on GPU timer value) > > > > > > > > # lspci -vvxxx -s 0:01.00 > > > > 00:01.0 PCI bridge: Intel Corporation Xeon E3-1200 v5/E3-1500 v5/6th > > > > Gen Core Processor PCIe Controller (x16) (rev 05) (prog-if 00 [Normal > > > > decode]) > > > > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- > > > > ParErr- Stepping- SERR- FastB2B- DisINTx- > > > > Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- > > > > <TAbort- <MAbort- >SERR- <PERR- INTx- > > > > Latency: 0 > > > > Interrupt: pin A routed to IRQ 16 > > > > Bus: primary=00, secondary=01, subordinate=01, sec-latency=0 > > > > I/O behind bridge: 0000e000-0000efff [size=4K] > > > > Memory behind bridge: ec000000-ed0fffff [size=17M] > > > > Prefetchable memory behind bridge: > > > > 00000000c0000000-00000000d1ffffff [size=288M] > > > > Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- > > > > <TAbort- <MAbort+ <SERR- <PERR- > > > > BridgeCtl: Parity- SERR- NoISA- VGA- VGA16+ MAbort- >Reset- FastB2B- > > > > PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- > > > > Capabilities: [88] Subsystem: Dell Device 07be > > > > Capabilities: [80] Power Management version 3 > > > > Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA > > > > PME(D0+,D1-,D2-,D3hot+,D3cold+) > > > > Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME- > > > > Capabilities: [90] MSI: Enable- Count=1/1 Maskable- 64bit- > > > > Address: 00000000 Data: 0000 > > > > Capabilities: [a0] Express (v2) Root Port (Slot+), MSI 00 > > > > DevCap: MaxPayload 256 bytes, PhantFunc 0 > > > > ExtTag- RBE+ > > > > DevCtl: CorrErr- NonFatalErr- FatalErr- UnsupReq- > > > > RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop- > > > > MaxPayload 256 bytes, MaxReadReq 128 bytes > > > > DevSta: CorrErr- NonFatalErr- FatalErr- UnsupReq- > > > > AuxPwr- TransPend- > > > > LnkCap: Port #2, Speed 8GT/s, Width x16, ASPM L0s L1, > > > > Exit Latency L0s <256ns, L1 <8us > > > > ClockPM- Surprise- LLActRep- BwNot+ ASPMOptComp+ > > > > LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- CommClk+ > > > > ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt- > > > > LnkSta: Speed 2.5GT/s (downgraded), Width x16 (ok) > > > > TrErr- Train- SlotClk+ DLActive- BWMgmt+ ABWMgmt+ > > > > SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- > > > > HotPlug- Surprise- > > > > Slot #1, PowerLimit 75.000W; Interlock- NoCompl+ > > > > SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- > > > > HPIrq- LinkChg- > > > > Control: AttnInd Unknown, PwrInd Unknown, > > > > Power- Interlock- > > > > SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- > > > > PresDet- Interlock- > > > > Changed: MRL- PresDet+ LinkState- > > > > RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- > > > > PMEIntEna- CRSVisible- > > > > RootCap: CRSVisible- > > > > RootSta: PME ReqID 0000, PMEStatus- PMEPending- > > > > DevCap2: Completion Timeout: Not Supported, > > > > TimeoutDis-, LTR+, OBFF Via WAKE# ARIFwd- > > > > AtomicOpsCap: Routing- 32bit+ 64bit+ 128bitCAS+ > > > > DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-, > > > > LTR+, OBFF Via WAKE# ARIFwd- > > > > AtomicOpsCtl: ReqEn- EgressBlck- > > > > LnkCtl2: Target Link Speed: 8GT/s, EnterCompliance- SpeedDis- > > > > Transmit Margin: Normal Operating Range, > > > > EnterModifiedCompliance- ComplianceSOS- > > > > Compliance De-emphasis: -6dB > > > > LnkSta2: Current De-emphasis Level: -6dB, > > > > EqualizationComplete-, EqualizationPhase1- > > > > EqualizationPhase2-, EqualizationPhase3-, > > > > LinkEqualizationRequest- > > > > Capabilities: [100 v1] Virtual Channel > > > > Caps: LPEVC=0 RefClk=100ns PATEntryBits=1 > > > > Arb: Fixed- WRR32- WRR64- WRR128- > > > > Ctrl: ArbSelect=Fixed > > > > Status: InProgress- > > > > VC0: Caps: PATOffset=00 MaxTimeSlots=1 RejSnoopTrans- > > > > Arb: Fixed+ WRR32- WRR64- WRR128- TWRR128- WRR256- > > > > Ctrl: Enable+ ID=0 ArbSelect=Fixed TC/VC=ff > > > > Status: NegoPending+ InProgress- > > > > Capabilities: [140 v1] Root Complex Link > > > > Desc: PortNumber=02 ComponentID=01 EltType=Config > > > > Link0: Desc: TargetPort=00 TargetComponent=01 > > > > AssocRCRB- LinkType=MemMapped LinkValid+ > > > > Addr: 00000000fed19000 > > > > Capabilities: [d94 v1] Secondary PCI Express <?> > > > > Kernel driver in use: pcieport > > > > 00: 86 80 01 19 07 00 10 00 05 00 04 06 00 00 81 00 > > > > 10: 00 00 00 00 00 00 00 00 00 01 01 00 e0 e0 00 20 > > > > 20: 00 ec 00 ed 01 c0 f1 d1 00 00 00 00 00 00 00 00 > > > > 30: 00 00 00 00 88 00 00 00 00 00 00 00 ff 01 10 00 > > > > 40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 > > > > 50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 > > > > 60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 > > > > 70: 00 00 00 00 00 00 00 00 00 62 17 00 00 00 00 0a > > > > 80: 01 90 03 c8 08 00 00 00 0d 80 00 00 28 10 be 07 > > > > 90: 05 a0 00 00 00 00 00 00 00 00 00 00 00 00 00 00 > > > > a0: 10 00 42 01 01 80 00 00 20 00 00 00 03 ad 61 02 > > > > b0: 40 00 01 d1 80 25 0c 00 00 00 08 00 00 00 00 00 > > > > c0: 00 00 00 00 80 0b 08 00 00 64 00 00 0e 00 00 00 > > > > d0: 43 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 > > > > e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 > > > > f0: 00 40 01 00 4e 01 01 22 00 00 00 00 e0 00 10 00 > > > > > > > > lspci -vvxxx -s 1:00.00 > > > > 01:00.0 3D controller: NVIDIA Corporation GP107M [GeForce GTX 1050 > > > > Mobile] (rev ff) (prog-if ff) > > > > !!! Unknown header type 7f > > > > Kernel driver in use: nouveau > > > > Kernel modules: nouveau > > > > 00: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff > > > > 10: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff > > > > 20: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff > > > > 30: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff > > > > 40: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff > > > > 50: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff > > > > 60: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff > > > > 70: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff > > > > 80: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff > > > > 90: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff > > > > a0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff > > > > b0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff > > > > c0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff > > > > d0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff > > > > e0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff > > > > f0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff > > > > > > > > On Tue, May 21, 2019 at 4:30 PM Karol Herbst <kherbst at redhat.com> wrote: > > > > > > > > > > On Tue, May 21, 2019 at 4:13 PM Bjorn Helgaas <helgaas at kernel.org> wrote: > > > > > > > > > > > > On Tue, May 21, 2019 at 03:28:48PM +0200, Karol Herbst wrote: > > > > > > > On Tue, May 21, 2019 at 3:11 PM Bjorn Helgaas <helgaas at kernel.org> wrote: > > > > > > > > On Tue, May 21, 2019 at 12:30:38AM +0200, Karol Herbst wrote: > > > > > > > > > On Mon, May 20, 2019 at 11:20 PM Bjorn Helgaas <helgaas at kernel.org> wrote: > > > > > > > > > > On Tue, May 07, 2019 at 10:12:45PM +0200, Karol Herbst wrote: > > > > > > > > > > > Apperantly things go south if we suspend the device with a different PCIE > > > > > > > > > > > link speed set than it got booted with. Fixes runtime suspend on my gp107. > > > > > > > > > > > > > > > > > > > > > > This all looks like some bug inside the pci subsystem and I would prefer a > > > > > > > > > > > fix there instead of nouveau, but maybe there is no real nice way of doing > > > > > > > > > > > that outside of drivers? > > > > > > > > > > > > > > > > > > > > I agree it would be nice to fix this in the PCI core if that's > > > > > > > > > > feasible. > > > > > > > > > > > > > > > > > > > > It looks like this driver changes the PCIe link speed using some > > > > > > > > > > device-specific mechanism. When we suspend, we put the device in > > > > > > > > > > D3cold, so it loses all its state. When we resume, the link probably > > > > > > > > > > comes up at the boot speed because nothing did that device-specific > > > > > > > > > > magic to change it, so you probably end up with the link being slow > > > > > > > > > > but the driver thinking it's configured to be fast, and maybe that > > > > > > > > > > combination doesn't work. > > > > > > > > > > > > > > > > > > > > If it requires something device-specific to change that link speed, I > > > > > > > > > > don't know how to put that in the PCI core. But maybe I'm missing > > > > > > > > > > something? > > > > > > > > > > > > > > > > > > > > Per the PCIe spec (r4.0, sec 1.2): > > > > > > > > > > > > > > > > > > > > Initialization – During hardware initialization, each PCI Express > > > > > > > > > > Link is set up following a negotiation of Lane widths and frequency > > > > > > > > > > of operation by the two agents at each end of the Link. No firmware > > > > > > > > > > or operating system software is involved. > > > > > > > > > > > > > > > > > > > > I have been assuming that this means device-specific link speed > > > > > > > > > > management is out of spec, but it seems pretty common that devices > > > > > > > > > > don't come up by themselves at the fastest possible link speed. So > > > > > > > > > > maybe the spec just intends that devices can operate at *some* valid > > > > > > > > > > speed. > > > > > > > > > > > > > > > > > > I would expect that devices kind of have to figure out what they can > > > > > > > > > operate on and the operating system kind of just checks what the > > > > > > > > > current state is and doesn't try to "restore" the old state or > > > > > > > > > something? > > > > > > > > > > > > > > > > The devices at each end of the link negotiate the width and speed of > > > > > > > > the link. This is done directly by the hardware without any help from > > > > > > > > the OS. > > > > > > > > > > > > > > > > The OS can read the current link state (Current Link Speed and > > > > > > > > Negotiated Link Width, both in the Link Status register). The OS has > > > > > > > > very little control over that state. It can't directly restore the > > > > > > > > state because the hardware has to negotiate a width & speed that > > > > > > > > result in reliable operation. > > > > > > > > > > > > > > > > > We don't do anything in the driver after the device was suspended. And > > > > > > > > > the 0x88000 is a mirror of the PCI config space, but we also got some > > > > > > > > > PCIe stuff at 0x8c000 which is used by newer GPUs for gen3 stuff > > > > > > > > > essentially. I have no idea how much of this is part of the actual pci > > > > > > > > > standard and how much is driver specific. But the driver also wants to > > > > > > > > > have some control over the link speed as it's tight to performance > > > > > > > > > states on GPU. > > > > > > > > > > > > > > > > As far as I'm aware, there is no generic PCIe way for the OS to > > > > > > > > influence the link width or speed. If the GPU driver needs to do > > > > > > > > that, it would be via some device-specific mechanism. > > > > > > > > > > > > > > > > > The big issue here is just, that the GPU boots with 8.0, some on-gpu > > > > > > > > > init mechanism decreases it to 2.5. If we suspend, the GPU or at least > > > > > > > > > the communication with the controller is broken. But if we set it to > > > > > > > > > the boot speed, resuming the GPU just works. So my assumption was, > > > > > > > > > that _something_ (might it be the controller or the pci subsystem) > > > > > > > > > tries to force to operate on an invalid link speed and because the > > > > > > > > > bridge controller is actually powered down as well (as all children > > > > > > > > > are in D3cold) I could imagine that something in the pci subsystem > > > > > > > > > actually restores the state which lets the controller fail to > > > > > > > > > establish communication again? > > > > > > > > > > > > > > > > 1) At boot-time, the Port and the GPU hardware negotiate 8.0 GT/s > > > > > > > > without OS/driver intervention. > > > > > > > > > > > > > > > > 2) Some mechanism reduces link speed to 2.5 GT/s. This probably > > > > > > > > requires driver intervention or at least some ACPI method. > > > > > > > > > > > > > > there is no driver intervention and Nouveau doesn't care at all. It's > > > > > > > all done on the GPU. We just upload a script and some firmware on to > > > > > > > the GPU. The script runs then on the PMU inside the GPU and this > > > > > > > script also causes changing the PCIe link settings. But from a Nouveau > > > > > > > point of view we don't care about the link before or after that script > > > > > > > was invoked. Also there is no ACPI method involved. > > > > > > > > > > > > > > But if there is something we should notify pci core about, maybe > > > > > > > that's something we have to do then? > > > > > > > > > > > > I don't think there's anything the PCI core could do with that > > > > > > information anyway. The PCI core doesn't care at all about the link > > > > > > speed, and it really can't influence it directly. > > > > > > > > > > > > > > 3) Suspend puts GPU into D3cold (powered off). > > > > > > > > > > > > > > > > 4) Resume restores GPU to D0, and the Port and GPU hardware again > > > > > > > > negotiate 8.0 GT/s without OS/driver intervention, just like at > > > > > > > > initial boot. > > > > > > > > > > > > > > No, that negotiation fails apparently as any attempt to read anything > > > > > > > from the device just fails inside pci core. Or something goes wrong > > > > > > > when resuming the bridge controller. > > > > > > > > > > > > I'm surprised the negotiation would fail even after a power cycle of > > > > > > the device. But if you can avoid the issue by running another script > > > > > > on the PMU before suspend, that's probably what you'll have to do. > > > > > > > > > > > > > > > > there is none as far as we know. Or at least nothing inside the vbios. > > > > > We still have to get signed PMU firmware images from Nvidia for full > > > > > support, but this still would be a hacky issue as we would depend on > > > > > those then (and without having those in redistributable form, there > > > > > isn't much we can do about except fixing it on the kernel side). > > > > > > > > > > > > > 5) Now the driver thinks the GPU is at 2.5 GT/s but it's actually at > > > > > > > > 8.0 GT/s. > > > > > > > > > > > > > > what is actually meant by "driver" here? The pci subsystem or Nouveau? > > > > > > > > > > > > I was thinking Nouveau because the PCI core doesn't care about the > > > > > > link speed. > > > > > > > > > > > > > > Without knowing more about the transition to 2.5 GT/s, I can't guess > > > > > > > > why the GPU wouldn't work after resume. From a PCIe point of view, > > > > > > > > the link is supposed to work and the device should be reachable > > > > > > > > independent of the link speed. But maybe there's some weird > > > > > > > > dependency between the GPU and the driver here. > > > > > > > > > > > > > > but the device isn't reachable at all, not even from the pci > > > > > > > subsystem. All reads fail/return a default error value (0xffffffff). > > > > > > > > > > > > Are these PCI config reads that return 0xffffffff? Or MMIO reads? > > > > > > "lspci -vvxxxx" of the bridge and the GPU might have a clue about > > > > > > whether a PCI error occurred. > > > > > > > > > > > > > > > > that's kind of problematic as it might just lock up my machine... but > > > > > let me try that. > > > > > > > > > > > > > It sounds like things work if you return to 8.0 GT/s before suspend, > > > > > > > > things work. That would make sense to me because then the driver's > > > > > > > > idea of the link state after resume would match the actual state. > > > > > > > > > > > > > > depends on what is meant by the driver here. Inside Nouveau we don't > > > > > > > care one bit about the current link speed, so I assume you mean > > > > > > > something inside the pci core code? > > > > > > > > > > > > > > > But I don't see a way to deal with this in the PCI core. The PCI core > > > > > > > > does save and restore most of the architected config space around > > > > > > > > suspend/resume, but since this appears to be a device-specific thing, > > > > > > > > the PCI core would have no idea how to save/restore it. > > > > > > > > > > > > > > if we assume that the negotiation on a device level works as intended, > > > > > > > then I would expect this to be a pci core issue, which might actually > > > > > > > be not fixable there. But if it's not, then we would have to put > > > > > > > something like that inside the runpm documentation to tell drivers > > > > > > > they have to do something about it. > > > > > > >lspci -vvxxxx > > > > > > > But again, for me it just sounds like the negotiation on the device > > > > > > > level fails or something inside pci core messes it up. > > > > > > > > > > > > To me it sounds like the PMU script messed something up, and the PCI > > > > > > core has no way to know what that was or how to fix it. > > > > > > > > > > > > > > > > sure, I am mainly wondering why it doesn't work after we power cycled > > > > > the GPU and the host bridge controller, because no matter what the > > > > > state was before, we have to reprobe instead of relying on a known > > > > > state, no? > > > > > > > > > > > > > > > > Signed-off-by: Karol Herbst <kherbst at redhat.com> > > > > > > > > > > > Reviewed-by: Lyude Paul <lyude at redhat.com> > > > > > > > > > > > --- > > > > > > > > > > > drm/nouveau/include/nvkm/subdev/pci.h | 5 +++-- > > > > > > > > > > > drm/nouveau/nvkm/subdev/pci/base.c | 9 +++++++-- > > > > > > > > > > > drm/nouveau/nvkm/subdev/pci/pcie.c | 24 ++++++++++++++++++++---- > > > > > > > > > > > drm/nouveau/nvkm/subdev/pci/priv.h | 2 ++ > > > > > > > > > > > 4 files changed, 32 insertions(+), 8 deletions(-) > > > > > > > > > > > > > > > > > > > > > > diff --git a/drm/nouveau/include/nvkm/subdev/pci.h b/drm/nouveau/include/nvkm/subdev/pci.h > > > > > > > > > > > index 1fdf3098..b23793a2 100644 > > > > > > > > > > > --- a/drm/nouveau/include/nvkm/subdev/pci.h > > > > > > > > > > > +++ b/drm/nouveau/include/nvkm/subdev/pci.h > > > > > > > > > > > @@ -26,8 +26,9 @@ struct nvkm_pci { > > > > > > > > > > > } agp; > > > > > > > > > > > > > > > > > > > > > > struct { > > > > > > > > > > > - enum nvkm_pcie_speed speed; > > > > > > > > > > > - u8 width; > > > > > > > > > > > + enum nvkm_pcie_speed cur_speed; > > > > > > > > > > > + enum nvkm_pcie_speed def_speed; > > > > > > > > > > > + u8 cur_width; > > > > > > > > > > > } pcie; > > > > > > > > > > > > > > > > > > > > > > bool msi; > > > > > > > > > > > diff --git a/drm/nouveau/nvkm/subdev/pci/base.c b/drm/nouveau/nvkm/subdev/pci/base.c > > > > > > > > > > > index ee2431a7..d9fb5a83 100644 > > > > > > > > > > > --- a/drm/nouveau/nvkm/subdev/pci/base.c > > > > > > > > > > > +++ b/drm/nouveau/nvkm/subdev/pci/base.c > > > > > > > > > > > @@ -90,6 +90,8 @@ nvkm_pci_fini(struct nvkm_subdev *subdev, bool suspend) > > > > > > > > > > > > > > > > > > > > > > if (pci->agp.bridge) > > > > > > > > > > > nvkm_agp_fini(pci); > > > > > > > > > > > + else if (pci_is_pcie(pci->pdev)) > > > > > > > > > > > + nvkm_pcie_fini(pci); > > > > > > > > > > > > > > > > > > > > > > return 0; > > > > > > > > > > > } > > > > > > > > > > > @@ -100,6 +102,8 @@ nvkm_pci_preinit(struct nvkm_subdev *subdev) > > > > > > > > > > > struct nvkm_pci *pci = nvkm_pci(subdev); > > > > > > > > > > > if (pci->agp.bridge) > > > > > > > > > > > nvkm_agp_preinit(pci); > > > > > > > > > > > + else if (pci_is_pcie(pci->pdev)) > > > > > > > > > > > + nvkm_pcie_preinit(pci); > > > > > > > > > > > return 0; > > > > > > > > > > > } > > > > > > > > > > > > > > > > > > > > > > @@ -193,8 +197,9 @@ nvkm_pci_new_(const struct nvkm_pci_func *func, struct nvkm_device *device, > > > > > > > > > > > pci->func = func; > > > > > > > > > > > pci->pdev = device->func->pci(device)->pdev; > > > > > > > > > > > pci->irq = -1; > > > > > > > > > > > - pci->pcie.speed = -1; > > > > > > > > > > > - pci->pcie.width = -1; > > > > > > > > > > > + pci->pcie.cur_speed = -1; > > > > > > > > > > > + pci->pcie.def_speed = -1; > > > > > > > > > > > + pci->pcie.cur_width = -1; > > > > > > > > > > > > > > > > > > > > > > if (device->type == NVKM_DEVICE_AGP) > > > > > > > > > > > nvkm_agp_ctor(pci); > > > > > > > > > > > diff --git a/drm/nouveau/nvkm/subdev/pci/pcie.c b/drm/nouveau/nvkm/subdev/pci/pcie.c > > > > > > > > > > > index 70ccbe0d..731dd30e 100644 > > > > > > > > > > > --- a/drm/nouveau/nvkm/subdev/pci/pcie.c > > > > > > > > > > > +++ b/drm/nouveau/nvkm/subdev/pci/pcie.c > > > > > > > > > > > @@ -85,6 +85,13 @@ nvkm_pcie_oneinit(struct nvkm_pci *pci) > > > > > > > > > > > return 0; > > > > > > > > > > > } > > > > > > > > > > > > > > > > > > > > > > +int > > > > > > > > > > > +nvkm_pcie_preinit(struct nvkm_pci *pci) > > > > > > > > > > > +{ > > > > > > > > > > > + pci->pcie.def_speed = nvkm_pcie_get_speed(pci); > > > > > > > > > > > + return 0; > > > > > > > > > > > +} > > > > > > > > > > > + > > > > > > > > > > > int > > > > > > > > > > > nvkm_pcie_init(struct nvkm_pci *pci) > > > > > > > > > > > { > > > > > > > > > > > @@ -105,12 +112,21 @@ nvkm_pcie_init(struct nvkm_pci *pci) > > > > > > > > > > > if (pci->func->pcie.init) > > > > > > > > > > > pci->func->pcie.init(pci); > > > > > > > > > > > > > > > > > > > > > > - if (pci->pcie.speed != -1) > > > > > > > > > > > - nvkm_pcie_set_link(pci, pci->pcie.speed, pci->pcie.width); > > > > > > > > > > > + if (pci->pcie.cur_speed != -1) > > > > > > > > > > > + nvkm_pcie_set_link(pci, pci->pcie.cur_speed, > > > > > > > > > > > + pci->pcie.cur_width); > > > > > > > > > > > > > > > > > > > > > > return 0; > > > > > > > > > > > } > > > > > > > > > > > > > > > > > > > > > > +int > > > > > > > > > > > +nvkm_pcie_fini(struct nvkm_pci *pci) > > > > > > > > > > > +{ > > > > > > > > > > > + if (!IS_ERR_VALUE(pci->pcie.def_speed)) > > > > > > > > > > > + return nvkm_pcie_set_link(pci, pci->pcie.def_speed, 16); > > > > > > > > > > > + return 0; > > > > > > > > > > > +} > > > > > > > > > > > + > > > > > > > > > > > int > > > > > > > > > > > nvkm_pcie_set_link(struct nvkm_pci *pci, enum nvkm_pcie_speed speed, u8 width) > > > > > > > > > > > { > > > > > > > > > > > @@ -146,8 +162,8 @@ nvkm_pcie_set_link(struct nvkm_pci *pci, enum nvkm_pcie_speed speed, u8 width) > > > > > > > > > > > speed = max_speed; > > > > > > > > > > > } > > > > > > > > > > > > > > > > > > > > > > - pci->pcie.speed = speed; > > > > > > > > > > > - pci->pcie.width = width; > > > > > > > > > > > + pci->pcie.cur_speed = speed; > > > > > > > > > > > + pci->pcie.cur_width = width; > > > > > > > > > > > > > > > > > > > > > > if (speed == cur_speed) { > > > > > > > > > > > nvkm_debug(subdev, "requested matches current speed\n"); > > > > > > > > > > > diff --git a/drm/nouveau/nvkm/subdev/pci/priv.h b/drm/nouveau/nvkm/subdev/pci/priv.h > > > > > > > > > > > index a0d4c007..e7744671 100644 > > > > > > > > > > > --- a/drm/nouveau/nvkm/subdev/pci/priv.h > > > > > > > > > > > +++ b/drm/nouveau/nvkm/subdev/pci/priv.h > > > > > > > > > > > @@ -60,5 +60,7 @@ enum nvkm_pcie_speed gk104_pcie_max_speed(struct nvkm_pci *); > > > > > > > > > > > int gk104_pcie_version_supported(struct nvkm_pci *); > > > > > > > > > > > > > > > > > > > > > > int nvkm_pcie_oneinit(struct nvkm_pci *); > > > > > > > > > > > +int nvkm_pcie_preinit(struct nvkm_pci *); > > > > > > > > > > > int nvkm_pcie_init(struct nvkm_pci *); > > > > > > > > > > > +int nvkm_pcie_fini(struct nvkm_pci *); > > > > > > > > > > > #endif > > > > > > > > > > > -- > > > > > > > > > > > 2.21.0 > > > > > > > > > > >
Maybe Matching Threads
- [PATCH v2 4/4] pci: save the boot pcie link speed and restore it on fini
- [PATCH v2 4/4] pci: save the boot pcie link speed and restore it on fini
- [PATCH v2 4/4] pci: save the boot pcie link speed and restore it on fini
- [PATCH v2 4/4] pci: save the boot pcie link speed and restore it on fini
- [PATCH v2 4/4] pci: save the boot pcie link speed and restore it on fini