Hello all, I have leased 1/3rd of a rack (14U space) in a top notch data center. I''ll be racking a layer 2 managed switch (a Dell PowerConnect 5224), four of my own servers (1U Opteron servers, single socket, dual core, dual NIC), as well 2 servers for 2 friends who will be subleasing from me. The package includes 6Mbps of bandwidth, burstable to 100Mbps. Bandwidth is tracked with 5-min samples, and as long as my 95th percentile is less than 6Mbps each month, there is no extra charge for bandwidth. I would like to use tc bandwidth shaping so that I can 1) ensure that I never have to pay for extra bandwidth in any month 2) be able to guarantee all servers a predefined minimum slice of bandwidth I am a software engineer and have only in the last couple years acquired some spotty knowledge of advanced networking concepts. I have been pouring over available documentation the last several days and it is very clear that I can satisfy my minimum requirements quite easily. However, its also clear that there is the potential for me to do some very fancy things that might be too fancy for my own good. So, I am looking for a little guidance from some experts willing to steer me in the right direction. For example, I have a choice between setting up one server as either a router or a bridge. The bridge approach seems quite interesting/ powerful, but I wonder if it would introduce unnecessary complexity that I would later regret. So far, it seems like the main advantage of a bridge is that if it has problems, I can easily bypass it. Otherwise, there is just the coolness factor of having a transparent firewall. I may want to carve up the /25 network assigned to me by the data center into some smaller networks (a /28 network for each of my friends, a /26 network for me), each with their own VLAN, so that with one firewall I can protect all servers from external attacks, but also protect my subleasers from each other. I can probably get my host to carve up the /25 network for me. If not, then I am forced to be a router. At first I thought this precluded configuring as a bridge, but now I see that I can configure a server as both a router and a bridge. I have a strong suspicion that is too fancy for my own good. One question I have is not so much about linux routing & traffic control, but instead a question about VLANs. If I configure server as a bridge, it needs to be logically between the data center''s upstream router, and my layer 2 switch. I can of course do that by instructing the datacenter to do the physical cabling that way. However, if I understand VLANs correctly, I can also just instruct the datacenter to cable everything to my switch. I would then make a two-port VLAN between the upstream router and the external interface of my bridge, and should get the same effect. Is that correct? The following are two things I am interested in trying to do in the future (if possible), but should probably wait to do until I have had some experience with a simpler configuration, but I would like mention now anyway. One reason is that if I don''t do them now, I can''t test them while I still have the servers in my possession, where I can most easily recover from mistakes. How risky will it be to make changes like the following to the setup remotely, if I want to minimize the chance of paying a sysadmin at the datacenter $100/ hour to help me recover from a mistake? It is possible that I will run some p2p service from one or more servers. If so, there may be as much of a need to control inbound bandwidth as there is to control outbound bandwidth. I understand that one can''t do shaping on ingress. From the documentation I have seen so far, I haven''t seen a clear example of controlling inbound bandwidth to a bridge via an egress qdisc on the internal interface. If I do that, should I use RED for that purpose? Finally, there is one thing that it would be nice to be able to do in the future, which is to try to do my bandwidth shaping based on the 5- min samples and 95th percentile measurements, and ideally understand the monthly billing cycle. Suppose that without bandwidth shaping my 95%-ile for one month would be 10Mbps or more. Is there a way to do bandwidth shaping so that I can allow 4.5% of my traffic in a month to be unmodified, but still have my 95%-ile be just under the 6Mbps limit? FYI, I''ll most likely be running Fedora Core 5, x86_64 on my servers, including the one that serves as the firewall/(router|bridge), unless someone here has good reason to steer me to a different configuration. Thanks in advance for any guidance. I plan to write up my configuration and lessons learned and will of course give credit in that write-up to all that contribute. Jim p.s. I have room for one more server in the rack in case anyone is interested in subleasing. I''m not looking to profit from subleasing, so your share of the cost would be a just prorated share of the total cost. Contact me privately at this email address if interested.