asterisk users - Jun 2006 - Very bad quality with AVM Fritz!card PCI andchan_capi

> > That is possible, how could I check that?
> > I can see that IRQ 17 is shared between eth0 and my fritz!card 
> but I
> > don't know if it changes anything:
> 
> Can you try it (or eth0) in a different slot (or change IRQ's in the
> BIOS if possible) to see if it makes any difference? That's the 
> only way
> to know for sure, anything else is just speculation :)
> 
> James
Unfortunately I can't, because the LAN board is integrated and I have no
PCI device left anymore.


> > 
> > ~# cat /proc/interrupts
> >            CPU0
> >   0: 1458224031    IO-APIC-edge  timer
> >   1:        953    IO-APIC-edge  i8042
> >   7:          0    IO-APIC-edge  parport0
> >   8:          1    IO-APIC-edge  rtc
> >   9:          1   IO-APIC-level  acpi
> >  14:     689691    IO-APIC-edge  ide0
> >  15:         24    IO-APIC-edge  ide1
> >  16: 1457845530   IO-APIC-level  uhci_hcd:usb1, wctdm
> >  17:  721402147   IO-APIC-level  fcpci, eth0
> >  18: 1457844720   IO-APIC-level  uhci_hcd:usb3, wctdm
> >  19:          0   IO-APIC-level  uhci_hcd:usb2
> >  23:          0   IO-APIC-level  ehci_hcd:usb4
> > NMI:          0
> > LOC: 1458419318
> > ERR:          0
> > MIS:          0
> > 
> > 
> > Benjamin
> > 
> > >
> > > >
> > > > >
> > > > > > Thanks,
> > > > > >
> > > > > > Ben
> > > > > >
> > > > > > </etc/asterisk/capi.conf>
> > > > > > [general]
> > > > > > rxgain=0.5
> > > > > > txgain=0.5
> > > > > > language=fr      ;set default language
> > > > > > ;ulaw=yes        ;set this, if you live in u-law
world
> > > instead of
> > > > > a-law
> > > > > > [ISDN1]
> > > > > >
> > > > > > isdnmode=DID     ;'MSN'
(point-to-multipoint) or 'DID'
> > > (direct
> > > > > inward dial)
> > > > > >                  ;when using NT-mode,
'DID' should be set in
> > > any
> > > > > case> incomingmsn=*    ;allow incoming calls to this
list of
> > > > > MSNs/DIDs, * = any
> > > > > > controller=1     ;capi controller number to use
> > > > > > group=9          ;dialout group
> > > > > > softdtmf=on      ;enable/disable software dtmf
detection,
> > > > > recommended> for AVM cards
> > > > > > relaxdtmf=on     ;in addition to softdtmf, you can
use
> > > relaxed dtmf
> > > > > > detection
> > > > > > accountcode=     ;Asterisk accountcode to use in
CDRs
> > > > > > context=capi-in  ;context for incoming calls
> > > > > > ;echosquelch=2   ;_VERY_PRIMITIVE_ echo
suppression
> > > > > > echocancel=yes  ;EICON DIVA SERVER (CAPI) echo
cancelation
> > > > > >                  ;(possible values: 'no',
'yes', 'force',
> > > 'g164',
> > > > > 'g165')> echocancelold=no ;use facility
selector 6 instead of
> > > > > correct 8
> > > > > > (necessary for older eicon drivers)
> > > > > > echotail=128     ;echo cancel tail setting
> > > > > > devices=2        ;number of concurrent calls on
this
> controller
> > > > > >                  ;(2 makes sense for single BRI,
30 for PRI)
> > > > > >

> > > That is possible, how could I check that?
> > > I can see that IRQ 17 is shared between eth0 and my fritz!card
> > but I
> > > don't know if it changes anything:
> >
> > Can you try it (or eth0) in a different slot (or change IRQ's in
the
> > BIOS if possible) to see if it makes any difference? That's the
> > only way
> > to know for sure, anything else is just speculation :)
> >
> > James
> 
> Unfortunately I can't, because the LAN board is integrated and I have
no
> PCI device left anymore.
You seem to have 2 wctdm adapters. Can you swap one of them with the
fritz card?

James