Displaying 20 results from an estimated 1200 matches similar to: "Very bad quality with AVM Fritz!card PCI andchan_capi"
2006 Jun 29
4
Very bad quality with AVM Fritz!card PCI and chan_capi
Hi everyone,
I have Asterisk SVN-trunk-r7498 running for a few months and I'm quite
happy with it. However, I am experiencing a quality issue with my AVM
Fritz!card PCI which is used with chan_capi. When somebody calls me on
this line he hears a lot of noise and I hear "scratches" and "plops". It
is very annoying. Below is is my /etc/asterisk/capi.conf
I've tried to
2006 Jun 19
2
Asterisk voicemail problem with isdn avm fritz!card
Hello everyone,
I have Asterisk SVN-trunk-r7498 installed on a server (celeron 2.4 Ghz,
256MB) with a TDM40b a TDM04b and an avm fritz!card pci.
I experience a problem with voicemail: my messages are good unless the
incoming call comes from isdn, which means via the avm fritz!card. In
this case (and in this case only) the message is disjointed and I can
hear at most 1 second out of a 1 minute
2007 Nov 29
0
[Copfilter] Copy of quarantined email - *** SPAM *** [6.6/6.0] Problems getting Asterisk to detect call in
I have installed an Asterisk 1.4 on Suse93 using a FritzCard.
Some calls are logged to the ISDN log, but Asterisk is not detecting
incoming calls.
I wonder whether some other device or process is preventing Asterisk
from gaining access to the isdn line?
Is there some way to ensure that only Asterisk can listening to the
line, or get it to share the line with some other device, such as the
fax
2007 Nov 26
3
Problems getting Asterisk to detect call in SUSE9.3, with FritzCard
I have installed an Asterisk 1.4 on Suse93 using a FritzCard.
Some calls are logged to the ISDN log, but Asterisk is not detecting
incoming calls.
I wonder whether some other device or process is preventing Asterisk
from gaining access to the isdn line?
Is there some way to ensure that only Asterisk can listening to the
line, or get it to share the line with some other device, such as the
fax
2004 May 28
3
2 Avm fritz passive card in the same box
Hi, I successfully installed 2 avm card in my asterisk box but I'm unable
to make call. My capi.conf is:
msn=0721111,07211115
incomingmsn=*
controller=1,2
softdtmf=1
context=default
echocancel=yes
callgroup=1
devices=2,2
my capi info :
Contr1: 2 B channels total, 2 B channels free.
Contr2: 2 B channels total, 2 B channels free.
my extensions.conf :
exten =>
2005 Oct 10
2
AVM Fritz! + chan_capi + mISDN + PTP
Hello everyone,
I have been using an AVM Fritz! card with chan_capi and mISDN for
quite a while in PTM mode and it was working finely.
Now, I needed more DID/MSN, so I switched to PTP. But now nothing
works anymore :(
I am using Asterisk on Debian Sarge stable and installed Asterisk
along with chan_capi from apt-get. I installed mISDN from the CVS of
isdn4linux.de.
It is :
- Asterisk
2003 May 14
2
AVM Fritz/Capi without suse ?
Hi All,
Has anyone had success with using the AVM Fritz PCI ISDN Card (v2) CAPI
drivers with a distro other than suse? The AVM driver is geared towards
suse, and after trying them with RedHat 9 I've not got very far. The
module compiles but dies when I attempt to modprobe it.
I've googled until I almost lost the will to live! What little
information
I can find seems to refer back to
2004 Sep 21
1
HELP on AVM Fritz with CAPI drivers for SMP RH 9
Hello,
I have been wrestling with installing the CAPI drivers for AVM Fritz in order
to use chan_capi with Asterisk.
I use an SMP machine, RH 9. I have found rpm's for CAPI and AVM drivers
(namely: capi4k-utils-2003.06.16-08.mungo.RH9.i686.rpm and kernel-2.4.20-8-
avmfcpci-03.11.02-08.mungo.RH9.i686.rpm), but I believe that they support only
single processor machines.
I've already
2005 Oct 20
0
German ISDN&DSL Card "AVM Fritz!Card DSL"
Hello everyone!
Has anyone had success in configuring the "Fritz!Card DSL" card, a
combination of an ISDN adapter and a DSL modem from the german AVM GmbH
(http://www.avm.de/) in a dom0 Domain (Xen 2.0.7)?
I had success in compiling the modules from
http://www.avm.de/de/Download/index.php3 and they load fine with
"modprobe fcdsl". But with the Xen dom0 Kernel they seem to
2003 May 01
0
AVM Fritz-PCI v2.0 and Asterisk
Hello all,
I would like to know about the support for this ISDN passive card AVM Fritz-PCI
v2.0 with Asterisk:
1. which drive should I use with Asterisk: isdn4linux or capi4linux from
AVM
(I read some messages on the asterisk-users archives but I didn't find
the answer)
2. if the drive is isdn4linux then HiSAX support (for passive cards) is
enough ?
and the device /dev/ttyI0 (for
2003 Aug 11
1
avm fritz pci
hello,
does anybody know how to setup avm fritz pci card in p2p mode ?
regards marian
--
SUNTEQ s. r. o.
Hviezdoslavova 9 # Prievidza # 971 04 # Slovak republic
Tel: +421-46-5430 754 # Fax: +421-46-5439 144
http://www.sunteq.sk/
------------------------------------------------------------
A mind is like a parachute... it only works when it's open.
2004 Sep 03
2
Using AVM Fritz!PCI as zap interface
Hello!
Is there a way to use AVM Fritz!PCI as a ZAP interface and have it
configured for ZAP channels?
Thanx in advance!
Roland Zagler
mailto:r.zagler@fog.at
@fog smart partners
2004 Dec 21
1
two avm usb isdn fritz v2.0 cards
I have a problem trying to install two avm fritz cards on one asterisk
machine. I am using fcusb2 driver. 1 card works perfectly.
I tried to recompile driver like it is described on this page but with
no success.
http://www.quiss.org/caiviar/Two-Fritzcards-HOWTO
I think the problem is that i can not find this part of code.
dev = pci_find_device (AVM_VENDOR_ID, AVM_DEVICE_ID, dev);
if
2004 Jan 21
1
ISDN p2p AVM Fritz Card
hello!
I'd like to use my asterisk-box on a p2p-line from my alcatel pbx.
isdn4linux and capi works fine on a s0-line from the pbx, but i need
more then 8 msns, cause i'd like to implement a voice-mail system and an
extension to our "old" pbx with voip-phones.
had anyone success using isdn4linux on a t0 (p2p) line (of course with
an inexpensive passive card like my avm
2003 May 27
1
Kernel Version for CAPI AVM Fritz PCI V2 / chan_capi / chan_alsa update to latest version..
Hello there
I have a serious issue with the AVM Fritz PCI V2
I have the following setup and the problem is, that the kernel freezes hard after
about 16 hours. The second problem is, that the S-Bus gets jammed as well, so
you can't even use a analog phone! on the NT
Kernel 2.4.21rc2 with ACPI Patch and of course capi
are there any reasons why this configuration should not work?
And the
2005 Jul 20
1
Fedora Core 3 + AVM Fritz ?
Someone have info about install an AVM fritz into FC3 ?
I'm getting problems with kernelcapi, after succesfully installed the
fcpci support.
Thanks
--
Adri? Vidal
adriavidal@gmail.com
Mail is better with 1Gmail
2003 May 27
0
Kernel Version for CAPI AVM Fritz PCI V2 /chan_capi /chan_alsa update to latest version
Hello there
I have a serious issue with the AVM Fritz PCI V2
I have the following setup and the problem is, that the kernel freezes hard after
about 16 hours. The second problem is, that the S-Bus gets jammed as well, so
you can't even use a analog phone! on the NT
Kernel 2.4.21rc2 with ACPI Patch and of course capi
are there any reasons why this configuration should not work?
And the
2003 Dec 15
1
AVM ISDN Fritz!Card USB works
Is case anyone wants to know... The Fritz! USB ISDN box works fine with
Asterisk!
I'm running CAPI 0.3.0 and love it, because the mini ITX server I have
only takes one PCI slot which is now filled with a 4 port Digium card.
2004 May 06
0
AVM Fritz doesn't pick up call or make calls
Hi,
I have an AVM Fritz! ISDN card connected to an NT1 unit (Australian).
I have no problems getting the drivers up and running but when using it with
asterisk nothing happens.
I call in using a mobile or analogue phone on either of the numbers and the
NT1 activity light either flashes or goes solid while ringing but it pauses
for a while and on a mobile i get call not answered and a busy
2004 Jun 08
0
Echo problems using AVM Fritz!PCI Card
Hi All,
I'm running the latest asterisk CVS code (from experimental), and
hardware-wise an AVM Fritz!PCI Card, together with chan_capi 0.3.3.
The problem is that any inbound/outbound calls result in echo on MY end
(the asterisk end). I've played with the echo settings in capi.conf
(mainly turning on echocancel and echosquelch, also tried playing with
rxgain/txgain) to no avail. The only