iH have a TDM400 w/ 1 FXS & 1FXO card. after about a day or so the FXO stops working. after a reboot i get the following error. to get the card working again i have to shutdown, physically unplug/replug the card (reboot only, power off/on does not work) any ideas what may be going wrong here? thanks - hcir Zaptel Configuration ===================== Channel map: Channel 01: FXO Kewlstart (Default) (Slaves: 01) Channel 02: FXS Kewlstart (Default) (Slaves: 02) 2 channels configured. ZT_CHANCONFIG failed on channel 1: No such device or address (6)
rich allen wrote:> iH > > have a TDM400 w/ 1 FXS & 1FXO card. after about a day or so the FXO > stops working. after a reboot i get the following error. to get the > card working again i have to shutdown, physically unplug/replug the card > (reboot only, power off/on does not work) any ideas what may be going > wrong here? > > thanks > - hcir >could it be that you've got the TDM400 on a shared IRQ with another device? you might want to check with lspci -v and make sure that nothing else is using the same IRQ as it is. Flynn
On Wed, Oct 06, 2004 at 08:53:21PM -0800, rich allen wrote:> > have a TDM400 w/ 1 FXS & 1FXO card. after about a day or so the FXO > stops working. after a reboot i get the following error. to get the > card working again i have to shutdown, physically unplug/replug the > card (reboot only, power off/on does not work) any ideas what may be > going wrong here?Make sure your FXO is *not* on port 1 on the card... I had a problem where I could not get 3 days of uptime before the system would lock of the card would freeze. Moving the FXO from port 1 to port 4 solved that problem. -- -M There are 10 kinds of people in this world: Those who can count in binary and those who cannot.
Rich, Is this the case for you as well, please let us know. Might be a problem if you have a four port FXO board. Thanks, Steve ----- Original Message ----- From: "Michael George" <george@mutualdata.com> To: "Asterisk Users Mailing List - Non-Commercial Discussion" <asterisk-users@lists.digium.com> Sent: Friday, October 08, 2004 7:18 AM Subject: Re: [Asterisk-Users] TDM400P stop responding> On Wed, Oct 06, 2004 at 08:53:21PM -0800, rich allen wrote: > > > > have a TDM400 w/ 1 FXS & 1FXO card. after about a day or so the FXO > > stops working. after a reboot i get the following error. to get the > > card working again i have to shutdown, physically unplug/replug the > > card (reboot only, power off/on does not work) any ideas what may be > > going wrong here? > > Make sure your FXO is *not* on port 1 on the card... I had a problemwhere I> could not get 3 days of uptime before the system would lock of the cardwould> freeze. Moving the FXO from port 1 to port 4 solved that problem. > > -- > -M > > There are 10 kinds of people in this world: > Those who can count in binary and those who cannot. > _______________________________________________ > Asterisk-Users mailing list > Asterisk-Users@lists.digium.com > http://lists.digium.com/mailman/listinfo/asterisk-users > To UNSUBSCRIBE or update options visit: > http://lists.digium.com/mailman/listinfo/asterisk-users >
iH i had forgotten about moving the FXO to port 1 ... am out of town so it will be Monday or Tuesday until i can move it and then about a day to know if that solves the problem. will report back then - hcir On Oct 8, 2004, at 3:18 AM, Michael George wrote:> On Wed, Oct 06, 2004 at 08:53:21PM -0800, rich allen wrote: >> >> have a TDM400 w/ 1 FXS & 1FXO card. after about a day or so the FXO >> stops working. after a reboot i get the following error. to get the >> card working again i have to shutdown, physically unplug/replug the >> card (reboot only, power off/on does not work) any ideas what may be >> going wrong here? > > Make sure your FXO is *not* on port 1 on the card... I had a problem > where I > could not get 3 days of uptime before the system would lock of the > card would > freeze. Moving the FXO from port 1 to port 4 solved that problem. >