search for: t100p

Below you will find, what I believe to be a typical setup with a T100P card. My question is - 1. Is this correct? 2. What kind of phones would be needed here... (Would you have to use Digital phones) And if so what would you recommend. PRI/T1----- | | | ---------------- | | | Channel Bank |...

Hello, Does anybody know of a place to get a half-height PCI slot bracket for the Digium T100P card? I have an application to fit them in 1U cases for small, deployable PBX's. The T100P itself is short enough to fit in a half-height slot but I need an appropriate mounting bracket to screw it into the case. Thanks, Mark Hagler

Hi- Perhaps someone with an E100P in hand can answer this: I just received an E100P from Digium (I normally buy quad boards) I noticed that the circuit board says "T100P" on it, and I assume that the T100P and E100P both use the same circuit board. Can someone please confirm that their E100P says "T100P" on the artwork? Thanks Scott Scott M. Stingel Emerging Voice Technology Inc. Palo Alto, California and London, England Email: scot...

I have a pri comming into a t100p in my asterisk box. I have a second t100p configured as pri_net connected to a nas server. I can route modem calls to the NAS with no problem, but I am concerned about isdn data connections. Will asterisk route 64k isdn calls between 2 t100p's? Also, should I expect worse modem connections...

To recap: T100P card wouldn't sync with the telco using line side clocking ( span=1,1,0.........) Had to use internal clocking (span=1,0,0.......) zttool showed Tx/Rx Levels as 0/ 1 For the grins of it I replaced the T100P card with another newer card from inventory. This newer card has the same rev o...

Management just approved purchase of a Digium T100P and a T1 card for our Merlin Legend Switch. I will appreciate comments from anyone performing this installation before: - Which T1 card did you use in the Merlin Legend? - Did you require any special interface? (CSU/DSU, etc) - Any items to watch during installation. Also we will need to remove o...

I'm trying to get a Carrier Access Corp. Channel Bank I working with a Digium T100P without success. What is stranger is that the status lights on the channel bank and T100P seem to change almost each time I power cycle the channel bank or reset the T100P. The channel bank has three status lights: T1, Framing, Status. T1 is green, Status is yellow, and Framing is usually red but...

I'm about to install a second T100P card in my asterisk system, and now I'm wondering how the system determines span-1 vs span-2. Does the position on the PCI bus determine this? TIA Mike

(to mods: sorry for any extra work I've put you through. Posting from my work account, as proper) Hello all, I'm back. I've got that lucky feeling that this will all work out very soon, and I hope that that is true. The issue: In my * server I have a t100P, connected with a T1 crossover cable to an Adtran TA750 with 2 FXO cards. After I do 'modprobe wct1xxp;ztcfg' the alarm on the card starts blinking red. running zttool confirmed that yes, it is a red alarm. I've read a few previous posts on this type of setup and I'm not too much cl...

anyone have a recommendation for a place I can buy cheap motherboards that supports those 64-bit 3.3 volt PCI slots for the T100P ? I can't find them at Fry's or anywhere locally. All I can find online is dual processor server boards that are overkill for this application. I would like to use a P3/ P4/ AMD single processor. No Xeons or dual processor junk. Anyone know why digium makes the 4 port cards in the 5....

Hi, Maybe someone has seen this before... I've installed a new T100P, but it doesn't seem to work. I've attached the T100P to an Adtran 750 using a crossover cable. The Adtran shows a red alarm on the T1 interface. The Adtran has been set to factory defaults with FXS cards in 1-3 and an FXO card in 5. The T100P shows no signs of life--the leds are not...

Hi Last week I installed Asterisk (release1) with digium t100p single span T1 (wct1xxp) board on Dell GX270 pc configured for PRI. Asterisk/t100p is currently the only user of the t1 line. All worked well for about a half a day, PSTN to SIP phones to non-SIP IP phones etc. Alas, since then I consistently get multitudes of blue alarms on all b-channels followed...

Hello, I am connecting Asterisk to an Adit 600 via a T100P. Unfortunately I am not able to get any lights on the T100P and the Adit 600 only shows red. I have already modprobed the t100p. Has anyone successfully connected these before? I've tried both a cross-over cable and a standard cat 5 cable, but I can't seem to get them to work. Any s...

List, I have a TE410P (T1 mode, all PRI) and a T100P (fxoks, for fxs channel bank). I cannot seem to get the T100P to send any clock to the channel bank. I prefer that it use the same clock source as the TE410P, but it doesn't matter if it's not in sync just as long as it's there. The TE410P is configured 3x pri_cpe, 1x pri_net. The t...

Hello, I have just received Adtran TSU 600 with 24 FXS ports. I have installed sucessfuly T100P card. Adtran is connected to t100p with crossover T1 cable. On T100P card I have a green light and on Adtran I do not get any errors or alarms. But I do not get dialtone on FXS ports. Adtran is configured: For Network Timing, fxs ports ore fxs_ls on Adtran. In zaptel.conf: span=1,1,0,esf,b8zs f...

Hi 2 all. I've a nice issue my * system. I have: asterisk latest cvs T100P + Zhone cb (3fxo+10fxs used) Diva Server 4BRI running Capi a bunch of pots and sip phones The whole system is running good (thanks to capigod and Bic. for the help with the Eicon Diva), but there's a very strange issue when calls arrive on the Diva and then bridged to the pots on the channel b...

Don & others, Thank you for your answer. The fog maybe lifting ;). The zaptel.conf file has the following in its comments: # # The timing parameter determines the selection of primary, secondary, and # so on sync sources. If this span should be considered a primary sync # source, then give it a value of "1". For a secondary, use "2", and so on. # To not use this as a

my target is to produce a linux router with T100p to Fract T1 24chan to ethernet and TDM 4channel FXO. I have not been able to get nethdlc to work, just get zaptel networking not configured if I set bchan and dchan the card comes to life, but I don't believe this is correct for what I want to accomplish. according to markster@ this is the...

I have following setup Asterisk - T100P -> Adtran TSU600 P + FXOcard -> PSTN line When PSTN line is plugged directly in to analog X100P caller id is received by Asterisk but when I plug it into adtran I'm not getting caller id. Any ideas what kind of setup Adtran TSU600 requires to pass caller id to T100P ??? regards m.

Hi, I'm seeing a problem when calling into my Asterisk server from a T100P with PRI signalling. I'm hoping someone has seen this as well, however, it's a little hard to explain. When I'm navigating through Asterisk on an inbound call from the PSTN, I'm getting a random 'noise' during the playback of sound files. The best way I can describe this...