Andrew P.
2005-Aug-22 15:18 UTC
[Xen-users] Problem with ttylinux setup (was: New user question)
Hi, I have the same problem as digz does. Following the configuration of ttylinux suggested by the user''s manual, I get this: ==========================================================[root@localhost boot]# uname -a Linux localhost.localdomain 2.6.12-1.1398_FC4xen0 #1 SMP Fri Jul 15 01:53:34 EDT 2005 i686 i686 i386 GNU/Linux [root@localhost boot]# xm create try -c Using config file "/etc/xen/try". Started domain TryDomain, console on port 9604 ************ REMOTE CONSOLE: CTRL-] TO QUIT ******** Linux version 2.6.12-1.1398_FC4xenU (bhcompile@tweety.build.redhat.com) (gcc version 4.0.0 20050519 (Red Hat 4.0.0-8)) #1 SMP Fri Jul 15 02:05:44 EDT 2005 BIOS-provided physical RAM map: Xen: 0000000000000000 - 0000000004000000 (usable) 64MB LOWMEM available. Using x86 segment limits to approximate NX protection DMI not present. IRQ lockup detection disabled Allocating PCI resources starting at 04000000 (gap: 04000000:fc000000) Built 1 zonelists Kernel command line: ip=1.2.3.4:1.2.3.4::::eth0:off root=/dev/sda1 ro Initializing CPU#0 PID hash table entries: 1024 (order: 10, 16384 bytes) Xen reported: 2798.716 MHz processor. Using tsc for high-res timesource Dentry cache hash table entries: 16384 (order: 4, 65536 bytes) Inode-cache hash table entries: 8192 (order: 3, 32768 bytes) Memory: 60800k/65536k available (1783k kernel code, 4648k reserved, 504k data, 156k init, 0k highmem) Checking if this processor honours the WP bit even in supervisor mode... Ok. Security Framework v1.0.0 initialized SELinux: Initializing. SELinux: Starting in permissive mode selinux_register_security: Registering secondary module capability Capability LSM initialized as secondary Mount-cache hash table entries: 512 CPU: Trace cache: 12K uops, L1 D cache: 8K CPU: L2 cache: 512K Enabling fast FPU save and restore... done. Enabling unmasked SIMD FPU exception support... done. Checking ''hlt'' instruction... disabled CPU0: Intel(R) Pentium(R) 4 CPU 2.80GHz stepping 09 per-CPU timeslice cutoff: 1463.16 usecs. task migration cache decay timeout: 2 msecs. SMP motherboard not detected. smpboot_clear_io_apic_irqs Brought up 1 CPUs NET: Registered protocol family 16 xen_mem: Initialising balloon driver. Grant table initialized audit: initializing netlink socket (disabled) audit(1124723172.606:1): initialized Total HugeTLB memory allocated, 0 VFS: Disk quotas dquot_6.5.1 Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) SELinux: Registering netfilter hooks Initializing Cryptographic API ksign: Installing public key data Loading keyring - Added public key 57652F2F3358E32D - User ID: Red Hat, Inc. (Kernel Module GPG key) io scheduler noop registered io scheduler anticipatory registered io scheduler deadline registered io scheduler cfq registered RAMDISK driver initialized: 16 RAM disks of 16384K size 1024 blocksize Xen virtual console successfully installed as tty1 Event-channel device installed. Blkif frontend is using grant tables. xen_blk: Initialising virtual block device driver xen_net: Initialising virtual ethernet driver. md: md driver 0.90.1 MAX_MD_DEVS=256, MD_SB_DISKS=27 NET: Registered protocol family 2 IP: routing cache hash table of 256 buckets, 4Kbytes TCP established hash table entries: 4096 (order: 4, 65536 bytes) TCP bind hash table entries: 4096 (order: 3, 49152 bytes) TCP: Hash tables configured (established 4096 bind 4096) Initializing IPsec netlink socket NET: Registered protocol family 1 NET: Registered protocol family 17 md: Autodetecting RAID arrays. md: autorun ... md: ... autorun DONE. kjournald starting. Commit interval 5 seconds EXT3-fs: mounted filesystem with ordered data mode. VFS: Mounted root (ext3 filesystem) readonly. Freeing unused kernel memory: 156k freed Inconsistency detected by ld.so: rtld.c: 1180: dl_main: Assertion ` ========================================================== Any ideas? Google says very little on this matter. Thanks, Andrew P. _______________________________________________ Xen-users mailing list Xen-users@lists.xensource.com http://lists.xensource.com/xen-users