Hello xenners,
It has recently
been brought to my attention that linux-image-2.6.32-5-xen-amd64
(2.6.32-30) was released in the Debian sid repositories [1]. Urgency
is set to high so I''d imagine the migration to squeeze will not take
long as well. The changelog shows [2]:
xen: backport TTM patches to use PCI API. Fixes PCIe GPU (specifically
Radeon and Nouveau) on Xen (Closes: #601341).
Previously I was successful using the nouveau video driver with
Xen on my laptop with nvidia graphic when using the
Debian 2.6.32-29+xen0 kernel from the ianc (Ian Campbells) xenbits
folder.
When I tried the new sid kernel (-30), I
found that I was able to boot natively (bare-metal) with full
functionality; meaning X with gnome desktop manager was working, able
to suspended and woken up, etc. (did not test sound).
When I
tried to boot the kernel through the Xen hypervisor it hangs X &
fb console like reported in a bug report [3]. My laptop is a Lenovo
ThinkPad R61 and my lspci -vvv -s 01:00.0 output is as
followed:
01:00.0 VGA compatible controller: nVidia
Corporation G84M [Quadro NVS 140M] (rev a1) (prog-if 00 [VGA
controller])
Subsystem: Lenovo ThinkPad T61
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+
66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency:
0, Cache Line Size: 64 bytes
Interrupt: pin A
routed to IRQ 16
Region 0: Memory at d6000000
(32-bit, non-prefetchable) [size=16M]
Region 1:
Memory at e0000000 (64-bit, prefetchable) [size=256M]
Region 3: Memory at d4000000 (64-bit, non-prefetchable)
[size=32M]
Region 5: I/O ports at 2000
[size=128]
Expansion ROM at <unassigned>
[disabled]
Capabilities: [60] Power Management
version 2
Flags: PMEClk-
DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0
PME-
Capabilities: [68] MSI: Enable- Count=1/1
Maskable- 64bit+
Address:
0000000000000000 Data: 0000
Capabilities:
[78] Express (v1) Endpoint, MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency
L0s <512ns, L1 <4us
ExtTag+ AttnBtn- AttnInd- PwrInd- RBE+
FLReset-
DevCtl:
Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd+ ExtTag- PhantFunc-
AuxPwr- NoSnoop+
MaxPayload 128 bytes, MaxReadReq 512 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq-
AuxPwr- TransPend-
LnkCap: Port #0, Speed 2.5GT/s, Width x16, ASPM L0s
L1, Latency L0 <512ns, L1 <4us
ClockPM- Surprise- LLActRep- BwNot-
LnkCtl: ASPM L0s Enabled; RCB
128 bytes Disabled- Retrain- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width
x16, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
Capabilities: [100 v1] Virtual Channel
Caps: LPEVC=0 RefClk=100ns PATEntryBits=1
Arb: Fixed- WRR32- WRR64-
WRR128-
Ctrl:
ArbSelect=Fixed
Status:
InProgress-
VC0:
Caps: PATOffset=00 MaxTimeSlots=1
RejSnoopTrans-
Arb: Fixed- WRR32- WRR64- WRR128- TWRR128-
WRR256-
Ctrl: Enable+ ID=0 ArbSelect=Fixed TC/VC=01
Status:
NegoPending- InProgress-
Capabilities: [128 v1]
Power Budgeting <?>
Capabilities: [600
v1] Vendor Specific Information: ID=0001 Rev=1 Len=024 <?>
Kernel driver in use: nouveau
Please advise on how one
should proceed. I''d like to know why 2.6.32-29+xen0 works but
2.6.52-30 does not work on my system.
[1]: http://packages.debian.org/sid/linux-image-2.6.32-5-xen-amd64 or
the source package at http://packages.qa.debian.org/l/linux-2.6.html
[2] :
http://packages.debian.org/changelogs/pool/main/l/linux-2.6/linux-2.6_2.6.32-30/changelog
[3]
:
http://bugs.debian.org/cgi-bin/bugreport.cgi?bug=601341
-M
_______________________________________________
Xen-users mailing list
Xen-users@lists.xensource.com
http://lists.xensource.com/xen-users
Mike Viau
2011-Jan-14 18:44 UTC
RE: [Xen-users] Issues using nouveau video driver on machine as Dom0
Hello xenners,
It has recently
been brought to my attention that linux-image-2.6.32-5-xen-amd64
(2.6.32-30) was released in the Debian sid repositories [1]. Urgency
is set to high so I''d imagine the migration to squeeze will not take
long as well. The changelog shows [2]:
xen: backport TTM patches to use PCI API. Fixes PCIe GPU (specifically
Radeon and Nouveau) on Xen (Closes: #601341).
Previously I was successful using the nouveau video driver with
Xen on my laptop with nvidia graphic when using the
Debian 2.6.32-29+xen0 kernel from the ianc (Ian Campbells) xenbits
folder.
When I tried the new sid kernel (-30), I
found that I was able to boot natively (bare-metal) with full
functionality; meaning X with gnome desktop manager was working, able
to suspended and woken up, etc. (did not test sound).
When I
tried to boot the kernel through the Xen hypervisor it hangs X &
fb console like reported in a bug report [3]. My laptop is a Lenovo
ThinkPad R61 and my lspci -vvv -s 01:00.0 output is as
followed:
01:00.0 VGA compatible controller: nVidia
Corporation G84M [Quadro NVS 140M] (rev a1) (prog-if 00 [VGA
controller])
Subsystem: Lenovo ThinkPad T61
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+
66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency:
0, Cache Line Size: 64 bytes
Interrupt: pin A
routed to IRQ 16
Region 0: Memory at d6000000
(32-bit, non-prefetchable) [size=16M]
Region 1:
Memory at e0000000 (64-bit, prefetchable) [size=256M]
Region 3: Memory at d4000000 (64-bit, non-prefetchable)
[size=32M]
Region 5: I/O ports at 2000
[size=128]
Expansion ROM at <unassigned>
[disabled]
Capabilities: [60] Power Management
version 2
Flags: PMEClk-
DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0
PME-
Capabilities: [68] MSI: Enable- Count=1/1
Maskable- 64bit+
Address:
0000000000000000 Data: 0000
Capabilities:
[78] Express (v1) Endpoint, MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency
L0s <512ns, L1 <4us
ExtTag+ AttnBtn- AttnInd- PwrInd- RBE+
FLReset-
DevCtl:
Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd+ ExtTag- PhantFunc-
AuxPwr- NoSnoop+
MaxPayload 128 bytes, MaxReadReq 512 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq-
AuxPwr- TransPend-
LnkCap: Port #0, Speed 2.5GT/s, Width x16, ASPM L0s
L1, Latency L0 <512ns, L1 <4us
ClockPM- Surprise- LLActRep- BwNot-
LnkCtl: ASPM L0s Enabled; RCB
128 bytes Disabled- Retrain- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width
x16, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
Capabilities: [100 v1] Virtual Channel
Caps: LPEVC=0 RefClk=100ns PATEntryBits=1
Arb: Fixed- WRR32- WRR64-
WRR128-
Ctrl:
ArbSelect=Fixed
Status:
InProgress-
VC0:
Caps: PATOffset=00 MaxTimeSlots=1
RejSnoopTrans-
Arb: Fixed- WRR32- WRR64- WRR128- TWRR128-
WRR256-
Ctrl: Enable+ ID=0 ArbSelect=Fixed TC/VC=01
Status:
NegoPending- InProgress-
Capabilities: [128 v1]
Power Budgeting <?>
Capabilities: [600
v1] Vendor Specific Information: ID=0001 Rev=1 Len=024 <?>
Kernel driver in use: nouveau
Attached is my dmesg output.
Please advise on how one
should proceed. I''d like to know why 2.6.32-29+xen0 works but
2.6.52-30 does not work on my system.
[1]: http://packages.debian.org/sid/linux-image-2.6.32-5-xen-amd64 or
the source package at http://packages.qa.debian.org/l/linux-2.6.html
[2] :
http://packages.debian.org/changelogs/pool/main/l/linux-2.6/linux-2.6_2.6.32-30/changelog
[3]
:
http://bugs.debian.org/cgi-bin/bugreport.cgi?bug=601341
-M
_______________________________________________
Xen-users mailing list
Xen-users@lists.xensource.com
http://lists.xensource.com/xen-users
_______________________________________________
Xen-users mailing list
Xen-users@lists.xensource.com
http://lists.xensource.com/xen-users
Mike Viau
2011-Jan-14 18:57 UTC
RE: [Xen-users] Issues using nouveau video driver on machine as Dom0
The previously attached dmesg output of the linux-image-2.6.32-5-xen-amd64
(2.6.32-30) kernel was booted on baremetal.
Below all pertains to the linux-image-2.6.32-5-xen-amd64 (2.6.32-29+xen0) kernel
booted via the Xen hypervisor.
[ 8.234475] Console: switching to colour frame buffer device 160x50 <--
this is approximently where the linux-image-2.6.32-5-xen-amd64 (2.6.32-30)
kernel fails loading through the hypervisor
[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Linux version 2.6.32-5-xen-amd64 (Debian 2.6.32-29+xen0)
(Ian.Campbell@citrix.com) (gcc version 4.3.5 (Debian 4.3.5-4) ) #1 SMP Thu Dec
23 12:55:59 UTC 2010
[ 0.000000] Command line: placeholder
root=UUID=3c9c2308-4a65-4011-8ca9-2899671a8a7c ro
[ 0.000000] KERNEL supported cpus:
[ 0.000000] Intel GenuineIntel
[ 0.000000] AMD AuthenticAMD
[ 0.000000] Centaur CentaurHauls
[ 0.000000] xen_release_chunk: looking at area pfn c0000-f0000: 196608 pages
freed
[ 0.000000] xen_release_chunk: looking at area pfn f4000-f4c80: 3200 pages
freed
[ 0.000000] released 199808 pages of unused memory
[ 0.000000] BIOS-provided physical RAM map:
[ 0.000000] Xen: 0000000000000000 - 000000000009d800 (usable)
[ 0.000000] Xen: 000000000009d800 - 0000000000100000 (reserved)
[ 0.000000] Xen: 0000000000100000 - 00000000bfeb0000 (usable)
[ 0.000000] Xen: 00000000bfeb0000 - 00000000bfecc000 (ACPI data)
[ 0.000000] Xen: 00000000bfecc000 - 00000000bff00000 (ACPI NVS)
[ 0.000000] Xen: 00000000bff00000 - 00000000c0000000 (reserved)
[ 0.000000] Xen: 00000000f0000000 - 00000000f4000000 (reserved)
[ 0.000000] Xen: 00000000fec00000 - 00000000fec10000 (reserved)
[ 0.000000] Xen: 00000000fed00000 - 00000000fed00400 (reserved)
[ 0.000000] Xen: 00000000fed14000 - 00000000fed1a000 (reserved)
[ 0.000000] Xen: 00000000fed1c000 - 00000000fed90000 (reserved)
[ 0.000000] Xen: 00000000fee00000 - 00000000fee01000 (reserved)
[ 0.000000] Xen: 00000000ff000000 - 0000000100000000 (reserved)
[ 0.000000] DMI present.
[ 0.000000] last_pfn = 0xbfeb0 max_arch_pfn = 0x400000000
[ 0.000000] x86 PAT enabled: cpu 0, old 0x50100070406, new 0x7010600070106
[ 0.000000] initial memory mapped : 0 - 20000000
[ 0.000000] init_memory_mapping: 0000000000000000-00000000bfeb0000
[ 0.000000] 0000000000 - 00bfeb0000 page 4k
[ 0.000000] kernel direct mapping tables up to bfeb0000 @ 100000-704000
[ 0.000000] RAMDISK: 016b2000 - 03229400
[ 0.000000] ACPI: RSDP 00000000000f69b0 00024 (v02 LENOVO)
[ 0.000000] ACPI: XSDT 00000000bfebb27e 0008C (v01 LENOVO TP-7K 00002290
LTP 00000000)
[ 0.000000] ACPI: FACP 00000000bfebb400 000F4 (v03 LENOVO TP-7K 00002290
LNVO 00000001)
[ 0.000000] ACPI Warning: 32/64X length mismatch in Gpe1Block: 0/32
(20090903/tbfadt-526)
[ 0.000000] ACPI Warning: Optional field Gpe1Block has zero address or
length: 000000000000102C/0 (20090903/tbfadt-557)
[ 0.000000] ACPI: DSDT 00000000bfebb81d 1044C (v01 LENOVO TP-7K 00002290
MSFT 03000000)
[ 0.000000] ACPI: FACS 00000000bfee4000 00040
[ 0.000000] ACPI: SSDT 00000000bfebb5b4 00269 (v01 LENOVO TP-7K 00002290
MSFT 03000000)
[ 0.000000] ACPI: ECDT 00000000bfecbc69 00052 (v01 LENOVO TP-7K 00002290
LNVO 00000001)
[ 0.000000] ACPI: TCPA 00000000bfecbcbb 00032 (v02 LENOVO TP-7K 00002290
LNVO 00000001)
[ 0.000000] ACPI: APIC 00000000bfecbced 00068 (v01 LENOVO TP-7K 00002290
LNVO 00000001)
[ 0.000000] ACPI: MCFG 00000000bfecbd55 0003C (v01 LENOVO TP-7K 00002290
LNVO 00000001)
[ 0.000000] ACPI: HPET 00000000bfecbd91 00038 (v01 LENOVO TP-7K 00002290
LNVO 00000001)
[ 0.000000] ACPI: SLIC 00000000bfecbe62 00176 (v01 LENOVO TP-7K 00002290
LTP 00000000)
[ 0.000000] ACPI: BOOT 00000000bfecbfd8 00028 (v01 LENOVO TP-7K 00002290
LTP 00000001)
[ 0.000000] ACPI: SSDT 00000000bfee26d9 0025F (v01 LENOVO TP-7K 00002290
INTL 20050513)
[ 0.000000] ACPI: SSDT 00000000bfee2938 000A6 (v01 LENOVO TP-7K 00002290
INTL 20050513)
[ 0.000000] ACPI: SSDT 00000000bfee29de 004F7 (v01 LENOVO TP-7K 00002290
INTL 20050513)
[ 0.000000] ACPI: SSDT 00000000bfee2ed5 001D8 (v01 LENOVO TP-7K 00002290
INTL 20050513)
[ 0.000000] ACPI: DMI detected: Lenovo ThinkPad R61
[ 0.000000] ACPI: Added _OSI(Linux)
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] No NUMA configuration found
[ 0.000000] Faking a node at 0000000000000000-00000000bfeb0000
[ 0.000000] Bootmem setup node 0 0000000000000000-00000000bfeb0000
[ 0.000000] NODE_DATA [0000000000008000 - 000000000000ffff]
[ 0.000000] bootmap [0000000000010000 - 0000000000027fd7] pages 18
[ 0.000000] (8 early reservations) ==> bootmem [0000000000 - 00bfeb0000]
[ 0.000000] #0 [0000000000 - 0000001000] BIOS data page ==>
[0000000000 - 0000001000]
[ 0.000000] #1 [00039d2000 - 00039f3000] XEN PAGETABLES ==>
[00039d2000 - 00039f3000]
[ 0.000000] #2 [0000006000 - 0000008000] TRAMPOLINE ==>
[0000006000 - 0000008000]
[ 0.000000] #3 [0001000000 - 0001691994] TEXT DATA BSS ==>
[0001000000 - 0001691994]
[ 0.000000] #4 [00016b2000 - 0003229400] RAMDISK ==>
[00016b2000 - 0003229400]
[ 0.000000] #5 [000322a000 - 00039d2000] XEN START INFO ==>
[000322a000 - 00039d2000]
[ 0.000000] #6 [0001692000 - 000169214c] BRK ==>
[0001692000 - 000169214c]
[ 0.000000] #7 [0000100000 - 00006e0000] PGTABLE ==>
[0000100000 - 00006e0000]
[ 0.000000] found SMP MP-table at [ffff8800000f69e0] f69e0
[ 0.000000] Zone PFN ranges:
[ 0.000000] DMA 0x00000000 -> 0x00001000
[ 0.000000] DMA32 0x00001000 -> 0x00100000
[ 0.000000] Normal 0x00100000 -> 0x00100000
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] early_node_map[2] active PFN ranges
[ 0.000000] 0: 0x00000000 -> 0x0000009d
[ 0.000000] 0: 0x00000100 -> 0x000bfeb0
[ 0.000000] On node 0 totalpages: 785997
[ 0.000000] DMA zone: 56 pages used for memmap
[ 0.000000] DMA zone: 1507 pages reserved
[ 0.000000] DMA zone: 2434 pages, LIFO batch:0
[ 0.000000] DMA32 zone: 10692 pages used for memmap
[ 0.000000] DMA32 zone: 771308 pages, LIFO batch:31
[ 0.000000] ACPI: PM-Timer IO Port: 0x1008
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
[ 0.000000] ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0])
[ 0.000000] IOAPIC[0]: apic_id 1, version 0, address 0xfec00000, GSI 0-0
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[ 0.000000] ERROR: Unable to locate IOAPIC for GSI 2
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[ 0.000000] ERROR: Unable to locate IOAPIC for GSI 9
[ 0.000000] Using ACPI (MADT) for SMP configuration information
[ 0.000000] ACPI: HPET id: 0x8086a201 base: 0xfed00000
[ 0.000000] SMP: Allowing 2 CPUs, 0 hotplug CPUs
[ 0.000000] nr_irqs_gsi: 256
[ 0.000000] PM: Registered nosave memory: 000000000009d000 - 000000000009e000
[ 0.000000] PM: Registered nosave memory: 000000000009e000 - 0000000000100000
[ 0.000000] Allocating PCI resources starting at c0000000 (gap:
c0000000:30000000)
[ 0.000000] Booting paravirtualized kernel on Xen
[ 0.000000] Xen version: 4.0.1 (preserve-AD) (dom0)
[ 0.000000] NR_CPUS:512 nr_cpumask_bits:512 nr_cpu_ids:2 nr_node_ids:1
[ 0.000000] PERCPU: Embedded 30 pages/cpu @ffff880003a29000 s90328 r8192
d24360 u122880
[ 0.000000] pcpu-alloc: s90328 r8192 d24360 u122880 alloc=30*4096
[ 0.000000] pcpu-alloc: [0] 0 [0] 1
[ 0.000000] trying to map vcpu_info 0 at ffff880003a34020, mfn 13ba34, offset
32
[ 0.000000] cpu 0 using vcpu_info at ffff880003a34020
[ 0.000000] trying to map vcpu_info 1 at ffff880003a52020, mfn 13ba52, offset
32
[ 0.000000] cpu 1 using vcpu_info at ffff880003a52020
[ 0.000000] Xen: using vcpu_info placement
[ 0.000000] Built 1 zonelists in Node order, mobility grouping on. Total
pages: 773742
[ 0.000000] Policy zone: DMA32
[ 0.000000] Kernel command line: placeholder
root=UUID=3c9c2308-4a65-4011-8ca9-2899671a8a7c ro
[ 0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.000000] Initializing CPU#0
[ 0.000000] DMA: Placing 64MB software IO TLB between ffff88000680b000 -
ffff88000a80b000
[ 0.000000] DMA: software IO TLB at phys 0x680b000 - 0xa80b000
[ 0.000000] xen_swiotlb_fixup: buf=ffff88000680b000 size=67108864
[ 0.000000] xen_swiotlb_fixup: buf=ffff88000a86b000 size=32768
[ 0.000000] Memory: 2985528k/3144384k available (3146k kernel code, 396k
absent, 158460k reserved, 1885k data, 600k init)
[ 0.000000] SLUB: Genslabs=14, HWalign=64, Order=0-3, MinObjects=0, CPUs=2,
Nodes=1
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] NR_IRQS:4352 nr_irqs:768
[ 0.000000] xen: --> irq=0
[ 0.000000] xen: --> irq=1
[ 0.000000] xen: --> irq=2
[ 0.000000] xen: --> irq=3
[ 0.000000] xen: --> irq=4
[ 0.000000] xen: --> irq=5
[ 0.000000] xen: --> irq=6
[ 0.000000] xen: --> irq=7
[ 0.000000] xen: --> irq=8
[ 0.000000] xen: --> irq=9
[ 0.000000] xen: --> irq=10
[ 0.000000] xen: --> irq=11
[ 0.000000] xen: --> irq=12
[ 0.000000] xen: --> irq=13
[ 0.000000] xen: --> irq=14
[ 0.000000] xen: --> irq=15
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[ 0.000000] xen: sci override: source_irq=9 global_irq=9 trigger=c polarity=1
[ 0.000000] xen: registering gsi 9 triggering 0 polarity 0
[ 0.000000] xen_allocate_pirq: returning irq 9 for gsi 9
[ 0.000000] xen: --> irq=9
[ 0.000000] xen: acpi sci 9
[ 0.000000] Console: colour VGA+ 80x25
[ 0.000000] console [tty0] enabled
[ 0.000000] Xen: using vcpuop timer interface
[ 0.000000] installing Xen timer for CPU 0
[ 0.000000] alloc irq_desc for 767 on node -1
[ 0.000000] alloc kstat_irqs on node -1
[ 0.000000] Detected 1995.057 MHz processor.
[ 0.004000] Calibrating delay loop (skipped), value calculated using timer
frequency.. 3990.11 BogoMIPS (lpj=7980228)
[ 0.004000] Security Framework initialized
[ 0.004000] SELinux: Disabled at boot.
[ 0.004000] Dentry cache hash table entries: 524288 (order: 10, 4194304
bytes)
[ 0.004186] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes)
[ 0.005299] Mount-cache hash table entries: 256
[ 0.005577] Initializing cgroup subsys ns
[ 0.005649] Initializing cgroup subsys cpuacct
[ 0.005717] Initializing cgroup subsys devices
[ 0.005784] Initializing cgroup subsys freezer
[ 0.005851] Initializing cgroup subsys net_cls
[ 0.005963] CPU: L1 I cache: 32K, L1 D cache: 32K
[ 0.006075] CPU: L2 cache: 4096K
[ 0.006142] CPU 0/0x0 -> Node 0
[ 0.006207] CPU: Physical Processor ID: 0
[ 0.006271] CPU: Processor Core ID: 0
[ 0.006340] mce: CPU supports 6 MCE banks
[ 0.006427] Performance Events: unsupported p6 CPU model 15 no PMU driver,
software events only.
[ 0.006618] SMP alternatives: switching to UP code
[ 0.008000] ACPI: Core revision 20090903
[ 0.032082] alloc irq_desc for 766 on node -1
[ 0.032086] alloc kstat_irqs on node -1
[ 0.032098] alloc irq_desc for 765 on node -1
[ 0.032101] alloc kstat_irqs on node -1
[ 0.032107] alloc irq_desc for 764 on node -1
[ 0.032110] alloc kstat_irqs on node -1
[ 0.032116] alloc irq_desc for 763 on node -1
[ 0.032118] alloc kstat_irqs on node -1
[ 0.032375] installing Xen timer for CPU 1
[ 0.032447] alloc irq_desc for 762 on node -1
[ 0.032450] alloc kstat_irqs on node -1
[ 0.032487] SMP alternatives: switching to SMP code
[ 0.036001] alloc irq_desc for 761 on node -1
[ 0.036001] alloc kstat_irqs on node -1
[ 0.036009] alloc irq_desc for 760 on node -1
[ 0.036012] alloc kstat_irqs on node -1
[ 0.036019] alloc irq_desc for 759 on node -1
[ 0.036022] alloc kstat_irqs on node -1
[ 0.036028] alloc irq_desc for 758 on node -1
[ 0.036030] alloc kstat_irqs on node -1
[ 0.004000] Initializing CPU#1
[ 0.004000] CPU: L1 I cache: 32K, L1 D cache: 32K
[ 0.004000] CPU: L2 cache: 4096K
[ 0.004000] CPU 1/0x0 -> Node 0
[ 0.004000] CPU: Physical Processor ID: 0
[ 0.004000] CPU: Processor Core ID: 1
[ 0.036144] Brought up 2 CPUs
[ 0.036600] CPU0 attaching sched-domain:
[ 0.036604] domain 0: span 0-1 level CPU
[ 0.036608] groups: 0 1
[ 0.036617] CPU1 attaching sched-domain:
[ 0.036620] domain 0: span 0-1 level CPU
[ 0.036624] groups: 1 0
[ 0.036701] devtmpfs: initialized
[ 0.040474] Grant table initialized
[ 0.040474] regulator: core version 0.5
[ 0.040474] NET: Registered protocol family 16
[ 0.040474] alloc irq_desc for 757 on node -1
[ 0.040474] alloc kstat_irqs on node -1
[ 0.040474] ACPI FADT declares the system doesn''t support PCIe ASPM,
so disable it
[ 0.040474] ACPI: bus type pci registered
[ 0.040474] sync cpu 0 get result 1 max_id 1
[ 0.040474] sync cpu 1 get result 1 max_id 1
[ 0.040474] alloc irq_desc for 756 on node -1
[ 0.040474] alloc kstat_irqs on node -1
[ 0.040474] PCI: MCFG configuration 0: base f0000000 segment 0 buses 0 - 63
[ 0.040474] PCI: MCFG area at f0000000 reserved in E820
[ 0.058674] PCI: Using MMCONFIG at f0000000 - f3ffffff
[ 0.058741] PCI: Using configuration type 1 for base access
[ 0.059416] bio: create slab <bio-0> at 0
[ 0.063147] ERROR: Unable to locate IOAPIC for GSI 9
[ 0.063273] ACPI: EC: EC description table is found, configuring boot EC
[ 0.077157] ACPI: BIOS _OSI(Linux) query honored via DMI
[ 0.091231] ACPI: Interpreter enabled
[ 0.091301] ACPI: (supports S0 S3 S4 S5)
[ 0.091574] ACPI: Using IOAPIC for interrupt routing
[ 0.107055] ACPI: EC: GPE = 0x12, I/O: command/status = 0x66, data = 0x62
[ 0.107200] ACPI: Power Resource [PUBS] (on)
[ 0.110032] ACPI: ACPI Dock Station Driver: 3 docks/bays found
[ 0.112100] ACPI: PCI Root Bridge [PCI0] (0000:00)
[ 0.112477] pci 0000:00:01.0: PME# supported from D0 D3hot D3cold
[ 0.112552] pci 0000:00:01.0: PME# disabled
[ 0.112892] pci 0000:00:19.0: reg 10 32bit mmio: [0xfe200000-0xfe21ffff]
[ 0.112915] pci 0000:00:19.0: reg 14 32bit mmio: [0xfe224000-0xfe224fff]
[ 0.112938] pci 0000:00:19.0: reg 18 io port: [0x1800-0x181f]
[ 0.113106] pci 0000:00:19.0: PME# supported from D0 D3hot D3cold
[ 0.113186] pci 0000:00:19.0: PME# disabled
[ 0.113422] pci 0000:00:1a.0: reg 20 io port: [0x1820-0x183f]
[ 0.113632] pci 0000:00:1a.1: reg 20 io port: [0x1840-0x185f]
[ 0.113834] pci 0000:00:1a.7: reg 10 32bit mmio: [0xfe225800-0xfe225bff]
[ 0.114022] pci 0000:00:1a.7: PME# supported from D0 D3hot D3cold
[ 0.114103] pci 0000:00:1a.7: PME# disabled
[ 0.114333] pci 0000:00:1b.0: reg 10 64bit mmio: [0xfe220000-0xfe223fff]
[ 0.114536] pci 0000:00:1b.0: PME# supported from D0 D3hot D3cold
[ 0.114616] pci 0000:00:1b.0: PME# disabled
[ 0.114987] pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold
[ 0.115067] pci 0000:00:1c.0: PME# disabled
[ 0.115448] pci 0000:00:1c.1: PME# supported from D0 D3hot D3cold
[ 0.115528] pci 0000:00:1c.1: PME# disabled
[ 0.115909] pci 0000:00:1c.2: PME# supported from D0 D3hot D3cold
[ 0.115989] pci 0000:00:1c.2: PME# disabled
[ 0.116265] pci 0000:00:1c.3: PME# supported from D0 D3hot D3cold
[ 0.116342] pci 0000:00:1c.3: PME# disabled
[ 0.116721] pci 0000:00:1c.4: PME# supported from D0 D3hot D3cold
[ 0.116798] pci 0000:00:1c.4: PME# disabled
[ 0.117071] pci 0000:00:1d.0: reg 20 io port: [0x1860-0x187f]
[ 0.117281] pci 0000:00:1d.1: reg 20 io port: [0x1880-0x189f]
[ 0.117493] pci 0000:00:1d.2: reg 20 io port: [0x18a0-0x18bf]
[ 0.117720] pci 0000:00:1d.7: reg 10 32bit mmio: [0xfe225c00-0xfe225fff]
[ 0.117927] pci 0000:00:1d.7: PME# supported from D0 D3hot D3cold
[ 0.118005] pci 0000:00:1d.7: PME# disabled
[ 0.118591] pci 0000:00:1f.0: quirk: region 1000-107f claimed by ICH6
ACPI/GPIO/TCO
[ 0.118678] pci 0000:00:1f.0: quirk: region 1180-11bf claimed by ICH6 GPIO
[ 0.118753] pci 0000:00:1f.0: ICH7 LPC Generic IO decode 1 PIO at 1600 (mask
007f)
[ 0.118839] pci 0000:00:1f.0: ICH7 LPC Generic IO decode 2 PIO at 15e0 (mask
000f)
[ 0.118926] pci 0000:00:1f.0: ICH7 LPC Generic IO decode 3 PIO at 1680 (mask
001f)
[ 0.119163] pci 0000:00:1f.1: reg 10 io port: [0x00-0x07]
[ 0.119186] pci 0000:00:1f.1: reg 14 io port: [0x00-0x03]
[ 0.119208] pci 0000:00:1f.1: reg 18 io port: [0x00-0x07]
[ 0.119230] pci 0000:00:1f.1: reg 1c io port: [0x00-0x03]
[ 0.119253] pci 0000:00:1f.1: reg 20 io port: [0x18c0-0x18cf]
[ 0.119494] pci 0000:00:1f.2: reg 10 io port: [0x18f8-0x18ff]
[ 0.119516] pci 0000:00:1f.2: reg 14 io port: [0x18ec-0x18ef]
[ 0.119539] pci 0000:00:1f.2: reg 18 io port: [0x18f0-0x18f7]
[ 0.119561] pci 0000:00:1f.2: reg 1c io port: [0x18e8-0x18eb]
[ 0.119584] pci 0000:00:1f.2: reg 20 io port: [0x1c00-0x1c1f]
[ 0.119606] pci 0000:00:1f.2: reg 24 32bit mmio: [0xfe225000-0xfe2257ff]
[ 0.119746] pci 0000:00:1f.2: PME# supported from D3hot
[ 0.119822] pci 0000:00:1f.2: PME# disabled
[ 0.119989] pci 0000:00:1f.3: reg 10 32bit mmio: [0xfe226000-0xfe2260ff]
[ 0.120001] pci 0000:00:1f.3: reg 20 io port: [0x1c20-0x1c3f]
[ 0.120001] pci 0000:01:00.0: reg 10 32bit mmio: [0xd6000000-0xd6ffffff]
[ 0.120001] pci 0000:01:00.0: reg 14 64bit mmio pref: [0xe0000000-0xefffffff]
[ 0.120001] pci 0000:01:00.0: reg 1c 64bit mmio: [0xd4000000-0xd5ffffff]
[ 0.120001] pci 0000:01:00.0: reg 24 io port: [0x2000-0x207f]
[ 0.120001] pci 0000:01:00.0: reg 30 32bit mmio pref: [0x000000-0x01ffff]
[ 0.120001] pci 0000:00:01.0: bridge io port: [0x2000-0x2fff]
[ 0.120001] pci 0000:00:01.0: bridge 32bit mmio: [0xd4000000-0xd6ffffff]
[ 0.120001] pci 0000:00:01.0: bridge 64bit mmio pref: [0xe0000000-0xefffffff]
[ 0.120001] pci 0000:00:1c.0: bridge io port: [0x3000-0x3fff]
[ 0.120001] pci 0000:00:1c.0: bridge 32bit mmio: [0xfc000000-0xfdffffff]
[ 0.120001] pci 0000:00:1c.0: bridge 64bit mmio pref: [0xf8000000-0xf80fffff]
[ 0.120227] pci 0000:03:00.0: reg 10 32bit mmio: [0xdf2ff000-0xdf2fffff]
[ 0.120540] pci 0000:03:00.0: PME# supported from D0 D3hot
[ 0.120621] pci 0000:03:00.0: PME# disabled
[ 0.120817] pci 0000:03:00.0: disabling ASPM on pre-1.1 PCIe device. You can
enable it with ''pcie_aspm=force''
[ 0.121064] pci 0000:00:1c.1: bridge io port: [0x4000-0x4fff]
[ 0.121077] pci 0000:00:1c.1: bridge 32bit mmio: [0xdc100000-0xdf2fffff]
[ 0.121100] pci 0000:00:1c.1: bridge 64bit mmio pref: [0xdfd00000-0xdfdfffff]
[ 0.121292] pci 0000:00:1c.2: bridge io port: [0x5000-0x5fff]
[ 0.121305] pci 0000:00:1c.2: bridge 32bit mmio: [0xd8000000-0xd9ffffff]
[ 0.121327] pci 0000:00:1c.2: bridge 64bit mmio pref: [0xdfa00000-0xdfafffff]
[ 0.121518] pci 0000:00:1c.3: bridge io port: [0x6000-0x6fff]
[ 0.121531] pci 0000:00:1c.3: bridge 32bit mmio: [0xd0000000-0xd1ffffff]
[ 0.121554] pci 0000:00:1c.3: bridge 64bit mmio pref: [0xdf700000-0xdf7fffff]
[ 0.121744] pci 0000:00:1c.4: bridge io port: [0x7000-0x7fff]
[ 0.121757] pci 0000:00:1c.4: bridge 32bit mmio: [0xcc000000-0xcdffffff]
[ 0.121780] pci 0000:00:1c.4: bridge 64bit mmio pref: [0xdf400000-0xdf4fffff]
[ 0.121920] pci 0000:15:00.0: reg 10 32bit mmio: [0xf8100000-0xf8100fff]
[ 0.121998] pci 0000:15:00.0: supports D1 D2
[ 0.122001] pci 0000:15:00.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.122081] pci 0000:15:00.0: PME# disabled
[ 0.122282] pci 0000:15:00.1: reg 10 32bit mmio: [0xf8101000-0xf81017ff]
[ 0.122487] pci 0000:15:00.1: supports D1 D2
[ 0.122490] pci 0000:15:00.1: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.122569] pci 0000:15:00.1: PME# disabled
[ 0.122771] pci 0000:15:00.2: reg 10 32bit mmio: [0xf8101800-0xf81018ff]
[ 0.122975] pci 0000:15:00.2: supports D1 D2
[ 0.122978] pci 0000:15:00.2: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.123057] pci 0000:15:00.2: PME# disabled
[ 0.123261] pci 0000:15:00.3: reg 10 32bit mmio: [0xf8101c00-0xf8101cff]
[ 0.123465] pci 0000:15:00.3: supports D1 D2
[ 0.123468] pci 0000:15:00.3: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.123548] pci 0000:15:00.3: PME# disabled
[ 0.123750] pci 0000:15:00.4: reg 10 32bit mmio: [0xf8102000-0xf81020ff]
[ 0.123954] pci 0000:15:00.4: supports D1 D2
[ 0.123957] pci 0000:15:00.4: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.124001] pci 0000:15:00.4: PME# disabled
[ 0.124001] pci 0000:15:00.5: reg 10 32bit mmio: [0xf8102400-0xf81024ff]
[ 0.124001] pci 0000:15:00.5: supports D1 D2
[ 0.124001] pci 0000:15:00.5: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.124001] pci 0000:15:00.5: PME# disabled
[ 0.124001] pci 0000:00:1e.0: transparent bridge
[ 0.124001] pci 0000:00:1e.0: bridge io port: [0x8000-0xbfff]
[ 0.124001] pci 0000:00:1e.0: bridge 32bit mmio: [0xf8100000-0xfbffffff]
[ 0.124001] pci 0000:00:1e.0: bridge 64bit mmio pref: [0xf4000000-0xf7ffffff]
[ 0.124001] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[ 0.124001] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.AGP_._PRT]
[ 0.124001] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.EXP0._PRT]
[ 0.124022] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.EXP1._PRT]
[ 0.124132] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.EXP2._PRT]
[ 0.124240] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.EXP3._PRT]
[ 0.124361] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.EXP4._PRT]
[ 0.124481] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCI1._PRT]
[ 0.139384] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 9 *10 11)
[ 0.140208] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 9 10 *11)
[ 0.140998] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 9 10 *11)
[ 0.141788] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 9 10 *11)
[ 0.142579] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 9 10 *11)
[ 0.143369] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 9 10 *11)
[ 0.144167] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 9 10 *11)
[ 0.144962] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 9 10 *11)
[ 0.145629] xen_balloon: Initialising balloon driver with page order 0.
[ 0.145791] vgaarb: device added:
PCI:0000:01:00.0,decodes=io+mem,owns=io+mem,locks=none
[ 0.145880] vgaarb: loaded
[ 0.145987] PCI: Using ACPI for IRQ routing
[ 0.145987] Switching to clocksource xen
[ 0.145987] pnp: PnP ACPI init
[ 0.145987] ACPI: bus type pnp registered
[ 0.148373] xen: registering gsi 13 triggering 1 polarity 0
[ 0.148377] xen_allocate_pirq: returning irq 13 for gsi 13
[ 0.148447] xen: --> irq=13
[ 0.148513] xen: registering gsi 8 triggering 1 polarity 0
[ 0.148516] xen_allocate_pirq: returning irq 8 for gsi 8
[ 0.148586] xen: --> irq=8
[ 0.148647] xen: registering gsi 1 triggering 1 polarity 0
[ 0.148650] xen_allocate_pirq: returning irq 1 for gsi 1
[ 0.148718] xen: --> irq=1
[ 0.148779] xen: registering gsi 12 triggering 1 polarity 0
[ 0.148782] xen_allocate_pirq: returning irq 12 for gsi 12
[ 0.148848] xen: --> irq=12
[ 0.151280] pnp: PnP ACPI: found 11 devices
[ 0.151349] ACPI: ACPI bus type pnp unregistered
[ 0.151428] system 00:00: iomem range 0x0-0x9ffff could not be reserved
[ 0.151500] system 00:00: iomem range 0xc0000-0xc3fff could not be reserved
[ 0.151573] system 00:00: iomem range 0xc4000-0xc7fff could not be reserved
[ 0.151645] system 00:00: iomem range 0xc8000-0xcbfff could not be reserved
[ 0.151718] system 00:00: iomem range 0xcc000-0xcffff could not be reserved
[ 0.151790] system 00:00: iomem range 0xd0000-0xd3fff could not be reserved
[ 0.151863] system 00:00: iomem range 0xe0000-0xe3fff could not be reserved
[ 0.151935] system 00:00: iomem range 0xe4000-0xe7fff could not be reserved
[ 0.152008] system 00:00: iomem range 0xe8000-0xebfff could not be reserved
[ 0.152079] system 00:00: iomem range 0xec000-0xeffff could not be reserved
[ 0.152151] system 00:00: iomem range 0xf0000-0xfffff could not be reserved
[ 0.152223] system 00:00: iomem range 0x100000-0xbfffffff could not be
reserved
[ 0.152308] system 00:00: iomem range 0xfec00000-0xfed3ffff could not be
reserved
[ 0.152394] system 00:00: iomem range 0xfed4c000-0xffffffff could not be
reserved
[ 0.152494] system 00:02: ioport range 0x164e-0x164f has been reserved
[ 0.152563] system 00:02: ioport range 0x1000-0x107f has been reserved
[ 0.152632] system 00:02: ioport range 0x1180-0x11bf has been reserved
[ 0.152701] system 00:02: ioport range 0x800-0x80f has been reserved
[ 0.152770] system 00:02: ioport range 0x15e0-0x15ef has been reserved
[ 0.152839] system 00:02: ioport range 0x1600-0x165f could not be reserved
[ 0.152909] system 00:02: iomem range 0xf0000000-0xf3ffffff has been reserved
[ 0.152979] system 00:02: iomem range 0xfed1c000-0xfed1ffff has been reserved
[ 0.153050] system 00:02: iomem range 0xfed14000-0xfed17fff has been reserved
[ 0.153120] system 00:02: iomem range 0xfed18000-0xfed18fff has been reserved
[ 0.153190] system 00:02: iomem range 0xfed19000-0xfed19fff has been reserved
[ 0.153260] system 00:02: iomem range 0xfed45000-0xfed4bfff has been reserved
[ 0.159551] PM-Timer failed consistency check (0x0xffffff) - aborting.
[ 0.159852] pci 0000:01:00.0: BAR 6: can''t allocate mem resource
[0xf0000000-0xefffffff]
[ 0.159938] pci 0000:00:01.0: PCI bridge, secondary bus 0000:01
[ 0.160005] pci 0000:00:01.0: IO window: 0x2000-0x2fff
[ 0.160005] pci 0000:00:01.0: MEM window: 0xd4000000-0xd6ffffff
[ 0.160005] pci 0000:00:01.0: PREFETCH window:
0x000000e0000000-0x000000efffffff
[ 0.160005] pci 0000:00:1c.0: PCI bridge, secondary bus 0000:02
[ 0.160005] pci 0000:00:1c.0: IO window: 0x3000-0x3fff
[ 0.160005] pci 0000:00:1c.0: MEM window: 0xfc000000-0xfdffffff
[ 0.160005] pci 0000:00:1c.0: PREFETCH window:
0x000000f8000000-0x000000f80fffff
[ 0.160005] pci 0000:00:1c.1: PCI bridge, secondary bus 0000:03
[ 0.160005] pci 0000:00:1c.1: IO window: 0x4000-0x4fff
[ 0.160005] pci 0000:00:1c.1: MEM window: 0xdc100000-0xdf2fffff
[ 0.160005] pci 0000:00:1c.1: PREFETCH window:
0x000000dfd00000-0x000000dfdfffff
[ 0.160005] pci 0000:00:1c.2: PCI bridge, secondary bus 0000:04
[ 0.160005] pci 0000:00:1c.2: IO window: 0x5000-0x5fff
[ 0.160005] pci 0000:00:1c.2: MEM window: 0xd8000000-0xd9ffffff
[ 0.160005] pci 0000:00:1c.2: PREFETCH window:
0x000000dfa00000-0x000000dfafffff
[ 0.160005] pci 0000:00:1c.3: PCI bridge, secondary bus 0000:05
[ 0.160005] pci 0000:00:1c.3: IO window: 0x6000-0x6fff
[ 0.160005] pci 0000:00:1c.3: MEM window: 0xd0000000-0xd1ffffff
[ 0.160005] pci 0000:00:1c.3: PREFETCH window:
0x000000df700000-0x000000df7fffff
[ 0.160005] pci 0000:00:1c.4: PCI bridge, secondary bus 0000:0d
[ 0.160005] pci 0000:00:1c.4: IO window: 0x7000-0x7fff
[ 0.160005] pci 0000:00:1c.4: MEM window: 0xcc000000-0xcdffffff
[ 0.160005] pci 0000:00:1c.4: PREFETCH window:
0x000000df400000-0x000000df4fffff
[ 0.160005] pci 0000:15:00.0: CardBus bridge, secondary bus 0000:16
[ 0.160005] pci 0000:15:00.0: IO window: 0x008000-0x0080ff
[ 0.160005] pci 0000:15:00.0: IO window: 0x008400-0x0084ff
[ 0.160005] pci 0000:15:00.0: PREFETCH window: 0xf4000000-0xf7ffffff
[ 0.160005] pci 0000:15:00.0: MEM window: 0xc0000000-0xc3ffffff
[ 0.160005] pci 0000:00:1e.0: PCI bridge, secondary bus 0000:15
[ 0.160005] pci 0000:00:1e.0: IO window: 0x8000-0xbfff
[ 0.160005] pci 0000:00:1e.0: MEM window: 0xf8100000-0xfbffffff
[ 0.160005] pci 0000:00:1e.0: PREFETCH window:
0x000000f4000000-0x000000f7ffffff
[ 0.160005] xen: registering gsi 16 triggering 0 polarity 1
[ 0.160005] alloc irq_desc for 16 on node -1
[ 0.160005] alloc kstat_irqs on node -1
[ 0.162630] xen: --> irq=16
[ 0.162638] pci 0000:00:01.0: PCI INT A -> GSI 16 (level, low) -> IRQ
16
[ 0.162712] pci 0000:00:01.0: setting latency timer to 64
[ 0.162739] xen: registering gsi 20 triggering 0 polarity 1
[ 0.162743] alloc irq_desc for 20 on node -1
[ 0.162746] alloc kstat_irqs on node -1
[ 0.162750] xen: --> irq=20
[ 0.162756] pci 0000:00:1c.0: PCI INT A -> GSI 20 (level, low) -> IRQ
20
[ 0.162834] pci 0000:00:1c.0: setting latency timer to 64
[ 0.162863] xen: registering gsi 21 triggering 0 polarity 1
[ 0.162868] alloc irq_desc for 21 on node -1
[ 0.162871] alloc kstat_irqs on node -1
[ 0.162875] xen: --> irq=21
[ 0.162880] pci 0000:00:1c.1: PCI INT B -> GSI 21 (level, low) -> IRQ
21
[ 0.162962] pci 0000:00:1c.1: setting latency timer to 64
[ 0.162990] xen: registering gsi 22 triggering 0 polarity 1
[ 0.162995] alloc irq_desc for 22 on node -1
[ 0.162998] alloc kstat_irqs on node -1
[ 0.163002] xen: --> irq=22
[ 0.163007] pci 0000:00:1c.2: PCI INT C -> GSI 22 (level, low) -> IRQ
22
[ 0.163085] pci 0000:00:1c.2: setting latency timer to 64
[ 0.163114] xen: registering gsi 23 triggering 0 polarity 1
[ 0.163118] alloc irq_desc for 23 on node -1
[ 0.163121] alloc kstat_irqs on node -1
[ 0.163125] xen: --> irq=23
[ 0.163130] pci 0000:00:1c.3: PCI INT D -> GSI 23 (level, low) -> IRQ
23
[ 0.163208] pci 0000:00:1c.3: setting latency timer to 64
[ 0.163237] xen: registering gsi 20 triggering 0 polarity 1
[ 0.163240] xen_allocate_pirq: returning irq 20 for gsi 20
[ 0.163306] xen: --> irq=20
[ 0.163309] Already setup the GSI :20
[ 0.163374] pci 0000:00:1c.4: PCI INT A -> GSI 20 (level, low) -> IRQ
20
[ 0.163452] pci 0000:00:1c.4: setting latency timer to 64
[ 0.163466] pci 0000:00:1e.0: enabling device (0005 -> 0007)
[ 0.163548] pci 0000:00:1e.0: setting latency timer to 64
[ 0.163579] xen: registering gsi 16 triggering 0 polarity 1
[ 0.163582] xen_allocate_pirq: returning irq 16 for gsi 16
[ 0.163649] xen: --> irq=16
[ 0.163652] Already setup the GSI :16
[ 0.163720] pci 0000:15:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ
16
[ 0.163803] pci_bus 0000:00: resource 0 io: [0x00-0xffff]
[ 0.163806] pci_bus 0000:00: resource 1 mem: [0x000000-0xffffffffffffffff]
[ 0.163810] pci_bus 0000:01: resource 0 io: [0x2000-0x2fff]
[ 0.163813] pci_bus 0000:01: resource 1 mem: [0xd4000000-0xd6ffffff]
[ 0.163816] pci_bus 0000:01: resource 2 pref mem [0xe0000000-0xefffffff]
[ 0.163820] pci_bus 0000:02: resource 0 io: [0x3000-0x3fff]
[ 0.163823] pci_bus 0000:02: resource 1 mem: [0xfc000000-0xfdffffff]
[ 0.163827] pci_bus 0000:02: resource 2 pref mem [0xf8000000-0xf80fffff]
[ 0.163830] pci_bus 0000:03: resource 0 io: [0x4000-0x4fff]
[ 0.163833] pci_bus 0000:03: resource 1 mem: [0xdc100000-0xdf2fffff]
[ 0.163837] pci_bus 0000:03: resource 2 pref mem [0xdfd00000-0xdfdfffff]
[ 0.163840] pci_bus 0000:04: resource 0 io: [0x5000-0x5fff]
[ 0.163843] pci_bus 0000:04: resource 1 mem: [0xd8000000-0xd9ffffff]
[ 0.163847] pci_bus 0000:04: resource 2 pref mem [0xdfa00000-0xdfafffff]
[ 0.163850] pci_bus 0000:05: resource 0 io: [0x6000-0x6fff]
[ 0.163853] pci_bus 0000:05: resource 1 mem: [0xd0000000-0xd1ffffff]
[ 0.163857] pci_bus 0000:05: resource 2 pref mem [0xdf700000-0xdf7fffff]
[ 0.163860] pci_bus 0000:0d: resource 0 io: [0x7000-0x7fff]
[ 0.163863] pci_bus 0000:0d: resource 1 mem: [0xcc000000-0xcdffffff]
[ 0.163867] pci_bus 0000:0d: resource 2 pref mem [0xdf400000-0xdf4fffff]
[ 0.163870] pci_bus 0000:15: resource 0 io: [0x8000-0xbfff]
[ 0.163873] pci_bus 0000:15: resource 1 mem: [0xf8100000-0xfbffffff]
[ 0.163877] pci_bus 0000:15: resource 2 pref mem [0xf4000000-0xf7ffffff]
[ 0.163880] pci_bus 0000:15: resource 3 io: [0x00-0xffff]
[ 0.163883] pci_bus 0000:15: resource 4 mem: [0x000000-0xffffffffffffffff]
[ 0.163887] pci_bus 0000:16: resource 0 io: [0x8000-0x80ff]
[ 0.163890] pci_bus 0000:16: resource 1 io: [0x8400-0x84ff]
[ 0.163893] pci_bus 0000:16: resource 2 pref mem [0xf4000000-0xf7ffffff]
[ 0.163896] pci_bus 0000:16: resource 3 mem: [0xc0000000-0xc3ffffff]
[ 0.163931] NET: Registered protocol family 2
[ 0.164372] IP route cache hash table entries: 131072 (order: 8, 1048576
bytes)
[ 0.167298] TCP established hash table entries: 524288 (order: 11, 8388608
bytes)
[ 0.171696] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
[ 0.172343] TCP: Hash tables configured (established 524288 bind 65536)
[ 0.172416] TCP reno registered
[ 0.172622] NET: Registered protocol family 1
[ 0.173085] pci 0000:01:00.0: Boot video device
[ 0.173173] Unpacking initramfs...
[ 0.214846] Freeing initrd memory: 28125k freed
[ 0.231780] PCI-DMA: Using software bounce buffering for IO (SWIOTLB)
[ 0.231863] DMA: Placing 64MB software IO TLB between ffff88000680b000 -
ffff88000a80b000
[ 0.231945] DMA: software IO TLB at phys 0x680b000 - 0xa80b000
[ 0.232339] Simple Boot Flag at 0x35 set to 0x1
[ 0.232853] audit: initializing netlink socket (disabled)
[ 0.232936] type=2000 audit(1295012759.130:1): initialized
[ 0.240747] HugeTLB registered 2 MB page size, pre-allocated 0 pages
[ 0.247872] VFS: Disk quotas dquot_6.5.2
[ 0.248013] Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[ 0.248181] msgmni has been set to 5886
[ 0.248552] alg: No test for stdrng (krng)
[ 0.248686] Block layer SCSI generic (bsg) driver version 0.4 loaded (major
253)
[ 0.248772] io scheduler noop registered
[ 0.248840] io scheduler anticipatory registered
[ 0.248909] io scheduler deadline registered
[ 0.249014] io scheduler cfq registered (default)
[ 0.249354] alloc irq_desc for 755 on node -1
[ 0.249357] alloc kstat_irqs on node -1
[ 0.249398] pcieport 0000:00:01.0: setting latency timer to 64
[ 0.249753] alloc irq_desc for 754 on node -1
[ 0.249756] alloc kstat_irqs on node -1
[ 0.249847] pcieport 0000:00:1c.0: setting latency timer to 64
[ 0.250278] alloc irq_desc for 753 on node -1
[ 0.250281] alloc kstat_irqs on node -1
[ 0.250345] pcieport 0000:00:1c.1: setting latency timer to 64
[ 0.250776] alloc irq_desc for 752 on node -1
[ 0.250779] alloc kstat_irqs on node -1
[ 0.250842] pcieport 0000:00:1c.2: setting latency timer to 64
[ 0.251278] alloc irq_desc for 751 on node -1
[ 0.251281] alloc kstat_irqs on node -1
[ 0.251344] pcieport 0000:00:1c.3: setting latency timer to 64
[ 0.251779] alloc irq_desc for 750 on node -1
[ 0.251782] alloc kstat_irqs on node -1
[ 0.251871] pcieport 0000:00:1c.4: setting latency timer to 64
[ 0.257335] registering netback
[ 0.257486] alloc irq_desc for 749 on node -1
[ 0.257489] alloc kstat_irqs on node -1
[ 0.259155] alloc irq_desc for 748 on node -1
[ 0.259159] alloc kstat_irqs on node -1
[ 0.259525] hpet_acpi_add: no address or irqs in _CRS
[ 0.259628] Linux agpgart interface v0.103
[ 0.259782] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[ 0.260353] input: Macintosh mouse button emulation as
/devices/virtual/input/input0
[ 0.260501] PNP: PS/2 Controller [PNP0303:KBD,PNP0f13:MOU] at 0x60,0x64 irq
1,12
[ 0.264033] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 0.269008] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 0.271070] mice: PS/2 mouse device common for all mice
[ 0.271213] rtc_cmos 00:07: RTC can wake from S4
[ 0.271325] rtc_cmos 00:07: rtc core: registered rtc_cmos as rtc0
[ 0.271459] rtc0: alarms up to one month, y3k, 114 bytes nvram
[ 0.271539] cpuidle: using governor ladder
[ 0.271604] cpuidle: using governor menu
[ 0.271673] No iBFT detected.
[ 0.272086] TCP cubic registered
[ 0.272316] NET: Registered protocol family 10
[ 0.272936] lo: Disabled Privacy Extensions
[ 0.273306] Mobile IPv6
[ 0.273372] NET: Registered protocol family 17
[ 0.273544] PM: Resume from disk failed.
[ 0.273558] registered taskstats version 1
[ 0.275283] rtc_cmos 00:07: setting system clock to 2011-01-14 13:45:58 UTC
(1295012758)
[ 0.275416] Initalizing network drop monitor service
[ 0.275563] Freeing unused kernel memory: 600k freed
[ 0.275918] Write protecting the kernel read-only data: 4308k
[ 0.277388] input: AT Translated Set 2 keyboard as
/devices/platform/i8042/serio0/input/input1
[ 0.312931] udev[61]: starting version 164
[ 0.411174] thermal LNXTHERM:01: registered as thermal_zone0
[ 0.411265] ACPI: Thermal Zone [THM0] (54 C)
[ 0.422443] thermal LNXTHERM:02: registered as thermal_zone1
[ 0.422531] ACPI: Thermal Zone [THM1] (56 C)
[ 0.522954] usbcore: registered new interface driver usbfs
[ 0.523059] usbcore: registered new interface driver hub
[ 0.523603] usbcore: registered new device driver usb
[ 0.538608] ehci_hcd: USB 2.0 ''Enhanced'' Host Controller
(EHCI) Driver
[ 0.539330] SCSI subsystem initialized
[ 0.542012] e1000e: Intel(R) PRO/1000 Network Driver - 1.0.2-k2
[ 0.542083] e1000e: Copyright (c) 1999-2008 Intel Corporation.
[ 0.542506] ehci_hcd 0000:00:1a.7: power state changed by ACPI to D0
[ 0.542823] ehci_hcd 0000:00:1a.7: power state changed by ACPI to D0
[ 0.542911] xen: registering gsi 22 triggering 0 polarity 1
[ 0.542915] xen_allocate_pirq: returning irq 22 for gsi 22
[ 0.542985] xen: --> irq=22
[ 0.542991] Already setup the GSI :22
[ 0.543060] ehci_hcd 0000:00:1a.7: PCI INT C -> GSI 22 (level, low) ->
IRQ 22
[ 0.543161] ehci_hcd 0000:00:1a.7: setting latency timer to 64
[ 0.543170] ehci_hcd 0000:00:1a.7: EHCI Host Controller
[ 0.543269] ehci_hcd 0000:00:1a.7: new USB bus registered, assigned bus
number 1
[ 0.547329] ehci_hcd 0000:00:1a.7: cache line size of 32 is not supported
[ 0.548077] ehci_hcd 0000:00:1a.7: irq 22, io mem 0xfe225800
[ 0.557835] libata version 3.00 loaded.
[ 0.561167] ehci_hcd 0000:00:1a.7: USB 2.0 started, EHCI 1.00
[ 0.561438] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 0.561509] usb usb1: New USB device strings: Mfr=3, Product=2,
SerialNumber=1
[ 0.561594] usb usb1: Product: EHCI Host Controller
[ 0.561666] usb usb1: Manufacturer: Linux 2.6.32-5-xen-amd64 ehci_hcd
[ 0.561739] usb usb1: SerialNumber: 0000:00:1a.7
[ 0.562116] usb usb1: configuration #1 chosen from 1 choice
[ 0.562269] hub 1-0:1.0: USB hub found
[ 0.562354] hub 1-0:1.0: 4 ports detected
[ 0.562567] xen: registering gsi 20 triggering 0 polarity 1
[ 0.562571] xen_allocate_pirq: returning irq 20 for gsi 20
[ 0.562638] xen: --> irq=20
[ 0.562643] Already setup the GSI :20
[ 0.562711] e1000e 0000:00:19.0: PCI INT A -> GSI 20 (level, low) ->
IRQ 20
[ 0.562798] e1000e 0000:00:19.0: setting latency timer to 64
[ 0.563098] alloc irq_desc for 747 on node -1
[ 0.563101] alloc kstat_irqs on node -1
[ 0.566664] xen: registering gsi 17 triggering 0 polarity 1
[ 0.566672] alloc irq_desc for 17 on node -1
[ 0.566676] alloc kstat_irqs on node -1
[ 0.566681] xen: --> irq=17
[ 0.566689] firewire_ohci 0000:15:00.1: PCI INT B -> GSI 17 (level, low)
-> IRQ 17
[ 0.566916] ricoh-mmc: Ricoh MMC Controller disabling driver
[ 0.566985] ricoh-mmc: Copyright(c) Philip Langdale
[ 0.578376] sdhci: Secure Digital Host Controller Interface driver
[ 0.578448] sdhci: Copyright(c) Pierre Ossman
[ 0.644021] firewire_ohci: Added fw-ohci device 0000:15:00.1, OHCI version
1.10
[ 0.644165] ricoh-mmc: Ricoh MMC controller found at 0000:15:00.3 [1180:0843]
(rev 11)
[ 0.644304] ricoh-mmc: Controller is now disabled.
[ 0.644788] sdhci-pci 0000:15:00.2: SDHCI controller found [1180:0822] (rev
21)
[ 0.644907] xen: registering gsi 18 triggering 0 polarity 1
[ 0.644914] alloc irq_desc for 18 on node -1
[ 0.644917] alloc kstat_irqs on node -1
[ 0.644923] xen: --> irq=18
[ 0.644931] sdhci-pci 0000:15:00.2: PCI INT C -> GSI 18 (level, low) ->
IRQ 18
[ 0.646052] sdhci-pci 0000:15:00.2: Will use DMA mode even though HW
doesn''t fully claim to support it.
[ 0.646148] sdhci-pci 0000:15:00.2: setting latency timer to 64
[ 0.647248] Registered led device: mmc0::
[ 0.648387] mmc0: SDHCI controller on PCI [0000:15:00.2] using DMA
[ 0.826652] 0000:00:19.0: eth0: (PCI Express:2.5GB/s:Width x1)
00:15:58:c9:91:92
[ 0.826739] 0000:00:19.0: eth0: Intel(R) PRO/1000 Network Connection
[ 0.826847] 0000:00:19.0: eth0: MAC: 6, PHY: 6, PBA No: ffffff-0ff
[ 0.827231] ehci_hcd 0000:00:1d.7: power state changed by ACPI to D0
[ 0.827553] ehci_hcd 0000:00:1d.7: power state changed by ACPI to D0
[ 0.827636] xen: registering gsi 19 triggering 0 polarity 1
[ 0.827643] alloc irq_desc for 19 on node -1
[ 0.827646] alloc kstat_irqs on node -1
[ 0.827651] xen: --> irq=19
[ 0.827659] ehci_hcd 0000:00:1d.7: PCI INT D -> GSI 19 (level, low) ->
IRQ 19
[ 0.827755] ehci_hcd 0000:00:1d.7: setting latency timer to 64
[ 0.827764] ehci_hcd 0000:00:1d.7: EHCI Host Controller
[ 0.827845] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus
number 2
[ 0.828015] ehci_hcd 0000:00:1d.7: debug port 1
[ 0.831991] ehci_hcd 0000:00:1d.7: cache line size of 32 is not supported
[ 0.832019] ehci_hcd 0000:00:1d.7: irq 19, io mem 0xfe225c00
[ 0.845021] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00
[ 0.845115] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
[ 0.845184] usb usb2: New USB device strings: Mfr=3, Product=2,
SerialNumber=1
[ 0.845266] usb usb2: Product: EHCI Host Controller
[ 0.845332] usb usb2: Manufacturer: Linux 2.6.32-5-xen-amd64 ehci_hcd
[ 0.845400] usb usb2: SerialNumber: 0000:00:1d.7
[ 0.845602] usb usb2: configuration #1 chosen from 1 choice
[ 0.845756] hub 2-0:1.0: USB hub found
[ 0.845839] hub 2-0:1.0: 6 ports detected
[ 0.845997] ahci 0000:00:1f.2: version 3.0
[ 0.846026] xen: registering gsi 16 triggering 0 polarity 1
[ 0.846030] xen_allocate_pirq: returning irq 16 for gsi 16
[ 0.846097] xen: --> irq=16
[ 0.846101] Already setup the GSI :16
[ 0.846169] ahci 0000:00:1f.2: PCI INT B -> GSI 16 (level, low) -> IRQ
16
[ 0.846326] alloc irq_desc for 746 on node -1
[ 0.846329] alloc kstat_irqs on node -1
[ 0.846447] ahci 0000:00:1f.2: AHCI 0001.0100 32 slots 3 ports 1.5 Gbps 0x5
impl SATA mode
[ 0.846531] ahci 0000:00:1f.2: flags: 64bit ncq sntf pm led clo pio slum part
ccc
[ 0.846624] ahci 0000:00:1f.2: setting latency timer to 64
[ 0.846956] scsi0 : ahci
[ 0.847234] scsi1 : ahci
[ 0.847469] scsi2 : ahci
[ 0.847759] ata1: SATA max UDMA/133 abar m2048@0xfe225000 port 0xfe225100 irq
746
[ 0.847841] ata2: DUMMY
[ 0.847908] ata3: SATA max UDMA/133 abar m2048@0xfe225000 port 0xfe225200 irq
746
[ 0.848045] ata_piix 0000:00:1f.1: version 2.13
[ 0.848059] xen: registering gsi 16 triggering 0 polarity 1
[ 0.848062] xen_allocate_pirq: returning irq 16 for gsi 16
[ 0.848129] xen: --> irq=16
[ 0.848133] Already setup the GSI :16
[ 0.848201] ata_piix 0000:00:1f.1: PCI INT C -> GSI 16 (level, low) ->
IRQ 16
[ 0.848335] ata_piix 0000:00:1f.1: setting latency timer to 64
[ 0.848487] scsi3 : ata_piix
[ 0.848700] scsi4 : ata_piix
[ 0.849807] ata4: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0x18c0 irq 14
[ 0.849880] ata5: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0x18c8 irq 15
[ 0.850377] ata5: port disabled. ignoring.
[ 0.860097] uhci_hcd: USB Universal Host Controller Interface driver
[ 0.860199] xen: registering gsi 20 triggering 0 polarity 1
[ 0.860202] xen_allocate_pirq: returning irq 20 for gsi 20
[ 0.860269] xen: --> irq=20
[ 0.860273] Already setup the GSI :20
[ 0.860339] uhci_hcd 0000:00:1a.0: PCI INT A -> GSI 20 (level, low) ->
IRQ 20
[ 0.860421] uhci_hcd 0000:00:1a.0: setting latency timer to 64
[ 0.860429] uhci_hcd 0000:00:1a.0: UHCI Host Controller
[ 0.860511] uhci_hcd 0000:00:1a.0: new USB bus registered, assigned bus
number 3
[ 0.860661] uhci_hcd 0000:00:1a.0: irq 20, io base 0x00001820
[ 0.860813] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001
[ 0.860882] usb usb3: New USB device strings: Mfr=3, Product=2,
SerialNumber=1
[ 0.860966] usb usb3: Product: UHCI Host Controller
[ 0.861035] usb usb3: Manufacturer: Linux 2.6.32-5-xen-amd64 uhci_hcd
[ 0.861103] usb usb3: SerialNumber: 0000:00:1a.0
[ 0.861299] usb usb3: configuration #1 chosen from 1 choice
[ 0.861450] hub 3-0:1.0: USB hub found
[ 0.861532] hub 3-0:1.0: 2 ports detected
[ 0.862021] uhci_hcd 0000:00:1a.1: power state changed by ACPI to D0
[ 0.862349] uhci_hcd 0000:00:1a.1: power state changed by ACPI to D0
[ 0.862426] xen: registering gsi 21 triggering 0 polarity 1
[ 0.862429] xen_allocate_pirq: returning irq 21 for gsi 21
[ 0.862497] xen: --> irq=21
[ 0.862501] Already setup the GSI :21
[ 0.862570] uhci_hcd 0000:00:1a.1: PCI INT B -> GSI 21 (level, low) ->
IRQ 21
[ 0.862662] uhci_hcd 0000:00:1a.1: setting latency timer to 64
[ 0.862670] uhci_hcd 0000:00:1a.1: UHCI Host Controller
[ 0.862756] uhci_hcd 0000:00:1a.1: new USB bus registered, assigned bus
number 4
[ 0.862929] uhci_hcd 0000:00:1a.1: irq 21, io base 0x00001840
[ 0.863078] usb usb4: New USB device found, idVendor=1d6b, idProduct=0001
[ 0.863147] usb usb4: New USB device strings: Mfr=3, Product=2,
SerialNumber=1
[ 0.863228] usb usb4: Product: UHCI Host Controller
[ 0.863295] usb usb4: Manufacturer: Linux 2.6.32-5-xen-amd64 uhci_hcd
[ 0.863363] usb usb4: SerialNumber: 0000:00:1a.1
[ 0.863505] usb usb4: configuration #1 chosen from 1 choice
[ 0.863660] hub 4-0:1.0: USB hub found
[ 0.863750] hub 4-0:1.0: 2 ports detected
[ 0.864157] uhci_hcd 0000:00:1d.0: power state changed by ACPI to D0
[ 0.864469] uhci_hcd 0000:00:1d.0: power state changed by ACPI to D0
[ 0.864546] xen: registering gsi 16 triggering 0 polarity 1
[ 0.864549] xen_allocate_pirq: returning irq 16 for gsi 16
[ 0.864618] xen: --> irq=16
[ 0.864622] Already setup the GSI :16
[ 0.864691] uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 16 (level, low) ->
IRQ 16
[ 0.864777] uhci_hcd 0000:00:1d.0: setting latency timer to 64
[ 0.864785] uhci_hcd 0000:00:1d.0: UHCI Host Controller
[ 0.864863] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus
number 5
[ 0.870386] uhci_hcd 0000:00:1d.0: irq 16, io base 0x00001860
[ 0.870541] usb usb5: New USB device found, idVendor=1d6b, idProduct=0001
[ 0.870611] usb usb5: New USB device strings: Mfr=3, Product=2,
SerialNumber=1
[ 0.870693] usb usb5: Product: UHCI Host Controller
[ 0.870759] usb usb5: Manufacturer: Linux 2.6.32-5-xen-amd64 uhci_hcd
[ 0.870827] usb usb5: SerialNumber: 0000:00:1d.0
[ 0.871023] usb usb5: configuration #1 chosen from 1 choice
[ 0.871171] hub 5-0:1.0: USB hub found
[ 0.871252] hub 5-0:1.0: 2 ports detected
[ 0.871407] xen: registering gsi 17 triggering 0 polarity 1
[ 0.871411] xen_allocate_pirq: returning irq 17 for gsi 17
[ 0.871478] xen: --> irq=17
[ 0.871482] Already setup the GSI :17
[ 0.871550] uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 17 (level, low) ->
IRQ 17
[ 0.871633] uhci_hcd 0000:00:1d.1: setting latency timer to 64
[ 0.871642] uhci_hcd 0000:00:1d.1: UHCI Host Controller
[ 0.871717] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus
number 6
[ 0.871867] uhci_hcd 0000:00:1d.1: irq 17, io base 0x00001880
[ 0.872015] usb usb6: New USB device found, idVendor=1d6b, idProduct=0001
[ 0.872085] usb usb6: New USB device strings: Mfr=3, Product=2,
SerialNumber=1
[ 0.872165] usb usb6: Product: UHCI Host Controller
[ 0.872231] usb usb6: Manufacturer: Linux 2.6.32-5-xen-amd64 uhci_hcd
[ 0.872299] usb usb6: SerialNumber: 0000:00:1d.1
[ 0.872482] usb usb6: configuration #1 chosen from 1 choice
[ 0.872632] hub 6-0:1.0: USB hub found
[ 0.872714] hub 6-0:1.0: 2 ports detected
[ 0.873120] uhci_hcd 0000:00:1d.2: power state changed by ACPI to D0
[ 0.873436] uhci_hcd 0000:00:1d.2: power state changed by ACPI to D0
[ 0.873513] xen: registering gsi 18 triggering 0 polarity 1
[ 0.873517] xen_allocate_pirq: returning irq 18 for gsi 18
[ 0.873586] xen: --> irq=18
[ 0.873590] Already setup the GSI :18
[ 0.873656] uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) ->
IRQ 18
[ 0.873740] uhci_hcd 0000:00:1d.2: setting latency timer to 64
[ 0.873748] uhci_hcd 0000:00:1d.2: UHCI Host Controller
[ 0.873825] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus
number 7
[ 0.873975] uhci_hcd 0000:00:1d.2: irq 18, io base 0x000018a0
[ 0.874131] usb usb7: New USB device found, idVendor=1d6b, idProduct=0001
[ 0.874201] usb usb7: New USB device strings: Mfr=3, Product=2,
SerialNumber=1
[ 0.874282] usb usb7: Product: UHCI Host Controller
[ 0.874347] usb usb7: Manufacturer: Linux 2.6.32-5-xen-amd64 uhci_hcd
[ 0.874415] usb usb7: SerialNumber: 0000:00:1d.2
[ 0.874605] usb usb7: configuration #1 chosen from 1 choice
[ 0.874758] hub 7-0:1.0: USB hub found
[ 0.874842] hub 7-0:1.0: 2 ports detected
[ 0.919103] mmc0: new high speed SDHC card at address a227
[ 0.924133] mmcblk0: mmc0:a227 SW08G 7.50 GiB
[ 0.924251] mmcblk0: p1
[ 1.013733] ata4.00: ATAPI: HL-DT-ST DVDRAM GMA-4082N, PX07, max UDMA/33
[ 1.028388] ata4.00: configured for UDMA/33
[ 1.144133] firewire_core: created device fw0: GUID 00016c2000175c12, S400
[ 1.168041] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 1.168139] ata3: SATA link down (SStatus 0 SControl 300)
[ 1.168732] ata1.00: ACPI cmd ef/02:00:00:00:00:a0 (SET FEATURES) succeeded
[ 1.168737] ata1.00: ACPI cmd f5/00:00:00:00:00:a0 (SECURITY FREEZE LOCK)
filtered out
[ 1.168823] ata1.00: ACPI cmd ef/10:03:00:00:00:a0 (SET FEATURES) filtered
out
[ 1.215162] ata1.00: ATA-8: TOSHIBA MK2565GSX, GJ003M, max UDMA/100
[ 1.215234] ata1.00: 488397168 sectors, multi 16: LBA48 NCQ (depth 31/32), AA
[ 1.216253] ata1.00: ACPI cmd ef/02:00:00:00:00:a0 (SET FEATURES) succeeded
[ 1.216258] ata1.00: ACPI cmd f5/00:00:00:00:00:a0 (SECURITY FREEZE LOCK)
filtered out
[ 1.216344] ata1.00: ACPI cmd ef/10:03:00:00:00:a0 (SET FEATURES) filtered
out
[ 1.217123] ata1.00: configured for UDMA/100
[ 1.233560] ata1.00: configured for UDMA/100
[ 1.233630] ata1: EH complete
[ 1.233813] scsi 0:0:0:0: Direct-Access ATA TOSHIBA MK2565GS GJ00
PQ: 0 ANSI: 5
[ 1.238041] scsi 3:0:0:0: CD-ROM HL-DT-ST DVDRAM GMA-4082N PX07
PQ: 0 ANSI: 5
[ 1.256059] sd 0:0:0:0: [sda] 488397168 512-byte logical blocks: (250 GB/232
GiB)
[ 1.256251] sd 0:0:0:0: [sda] Write Protect is off
[ 1.256320] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 1.256366] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled,
doesn''t support DPO or FUA
[ 1.256695] sda:sr0: scsi3-mmc drive: 24x/24x writer dvd-ram cd/rw xa/form2
cdda tray
[ 1.270594] Uniform CD-ROM driver Revision: 3.20
[ 1.271020] sr 3:0:0:0: Attached scsi CD-ROM sr0
[ 1.300549] sda1 sda2 sda3 < sda5 sda6 sda7 >
[ 1.337238] sd 0:0:0:0: [sda] Attached SCSI disk
[ 1.344916] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 1.345032] sr 3:0:0:0: Attached scsi generic sg1 type 5
[ 1.952331] device-mapper: uevent: version 1.0.3
[ 1.952563] device-mapper: ioctl: 4.15.0-ioctl (2009-04-01) initialised:
dm-devel@redhat.com
[ 2.140394] PM: Starting manual resume from disk
[ 2.140477] PM: Resume from partition 8:6
[ 2.140479] PM: Checking hibernation image.
[ 2.162759] PM: Error -22 checking image file
[ 2.162762] PM: Resume from disk failed.
[ 2.269953] EXT4-fs (sda5): mounted filesystem with ordered data mode
[ 4.008431] udev[379]: starting version 164
[ 4.587570] input: Lid Switch as
/devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0D:00/input/input2
[ 4.588390] ACPI: Lid Switch [LID]
[ 4.588531] input: Sleep Button as
/devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0E:00/input/input3
[ 4.588630] ACPI: Sleep Button [SLPB]
[ 4.588786] input: Power Button as
/devices/LNXSYSTM:00/LNXPWRBN:00/input/input4
[ 4.588879] ACPI: Power Button [PWRF]
[ 4.652516] ACPI: SSDT 00000000bfee1b32 002C4 (v01 PmRef Cpu0Ist 00000100
INTL 20050513)
[ 4.654021] ACPI: SSDT 00000000bfee1e7b 0085E (v01 PmRef Cpu0Cst 00000100
INTL 20050513)
[ 4.658712] Marking TSC unstable due to TSC halts in idle
[ 4.658851] ACPI: CPU-1 (power states: C1[C1] C2[C2] C3[C3])
[ 4.659690] ACPI: SSDT 00000000bfee1a6a 000C8 (v01 PmRef Cpu1Ist 00000100
INTL 20050513)
[ 4.660944] ACPI: SSDT 00000000bfee1df6 00085 (v01 PmRef Cpu1Cst 00000100
INTL 20050513)
[ 4.665366] ACPI: CPU-1 (power states: C1[C1] C2[C2] C3[C3])
[ 4.719144] input: PC Speaker as /devices/platform/pcspkr/input/input5
[ 4.730669] Non-volatile memory driver v1.3
[ 4.752305] ACPI: AC Adapter [AC] (on-line)
[ 4.756527] ACPI: WMI: Mapper loaded
[ 4.781681] ACPI: Battery Slot [BAT0] (battery present)
[ 4.996960] acpi device:06: registered as cooling_device0
[ 4.998909] input: Video Bus as
/devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/device:05/LNXVIDEO:01/input/input6
[ 5.005361] ACPI: Video Device [VID1] (multi-head: yes rom: no post: no)
[ 5.319679] yenta_cardbus 0000:15:00.0: CardBus bridge found [17aa:20c6]
[ 5.444989] yenta_cardbus 0000:15:00.0: ISA IRQ mask 0x0cb8, PCI irq 16
[ 5.445111] yenta_cardbus 0000:15:00.0: Socket status: 30000006
[ 5.445229] yenta_cardbus 0000:15:00.0: pcmcia: parent PCI bridge I/O window:
0x8000 - 0xbfff
[ 5.445362] yenta_cardbus 0000:15:00.0: pcmcia: parent PCI bridge Memory
window: 0xf8100000 - 0xfbffffff
[ 5.445497] yenta_cardbus 0000:15:00.0: pcmcia: parent PCI bridge Memory
window: 0xf4000000 - 0xf7ffffff
[ 5.520206] thinkpad_acpi: ThinkPad ACPI Extras v0.23
[ 5.520322] thinkpad_acpi: http://ibm-acpi.sf.net/
[ 5.520430] thinkpad_acpi: ThinkPad BIOS 7KETC9WW (2.29 ), EC 7KHT24WW-1.08
[ 5.520541] thinkpad_acpi: Lenovo ThinkPad R61, model 8919W1B
[ 5.537629] thinkpad_acpi: ACPI backlight control delay disabled
[ 5.538418] thinkpad_acpi: radio switch found; radios are enabled
[ 5.538909] thinkpad_acpi: This ThinkPad has standard ACPI backlight
brightness control, supported by the ACPI video driver
[ 5.539048] thinkpad_acpi: Disabling thinkpad-acpi brightness events by
default...
[ 5.542611] cfg80211: Using static regulatory domain info
[ 5.542681] cfg80211: Regulatory domain: US
[ 5.542747] (start_freq - end_freq @ bandwidth), (max_antenna_gain,
max_eirp)
[ 5.542830] (2402000 KHz - 2472000 KHz @ 40000 KHz), (600 mBi, 2700 mBm)
[ 5.542899] (5170000 KHz - 5190000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
[ 5.542968] (5190000 KHz - 5210000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
[ 5.543038] (5210000 KHz - 5230000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
[ 5.543107] (5230000 KHz - 5330000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
[ 5.543176] (5735000 KHz - 5835000 KHz @ 40000 KHz), (600 mBi, 3000 mBm)
[ 5.543887] cfg80211: Calling CRDA for country: US
[ 5.552845] Registered led device: tpacpi::thinklight
[ 5.552958] Registered led device: tpacpi::power
[ 5.553046] Registered led device: tpacpi::standby
[ 5.553135] Registered led device: tpacpi::thinkvantage
[ 5.557277] thinkpad_acpi: Standard ACPI backlight interface available, not
loading native one.
[ 5.557744] input: ThinkPad Extra Buttons as
/devices/platform/thinkpad_acpi/input/input7
[ 5.650322] xen: registering gsi 23 triggering 0 polarity 1
[ 5.650326] xen_allocate_pirq: returning irq 23 for gsi 23
[ 5.650394] xen: --> irq=23
[ 5.650399] Already setup the GSI :23
[ 5.650461] i801_smbus 0000:00:1f.3: PCI INT A -> GSI 23 (level, low)
-> IRQ 23
[ 5.746437] input: DualPoint Stick as
/devices/platform/i8042/serio1/input/input8
[ 5.777789] input: AlpsPS/2 ALPS DualPoint TouchPad as
/devices/platform/i8042/serio1/input/input9
[ 6.063334] [drm] Initialized drm 1.1.0 20060810
[ 6.070949] iwl3945: Intel(R) PRO/Wireless 3945ABG/BG Network Connection
driver for Linux, 1.2.26ks
[ 6.072004] iwl3945: Copyright(c) 2003-2009 Intel Corporation
[ 6.076555] xen: registering gsi 17 triggering 0 polarity 1
[ 6.076559] xen_allocate_pirq: returning irq 17 for gsi 17
[ 6.076629] xen: --> irq=17
[ 6.076634] Already setup the GSI :17
[ 6.076699] iwl3945 0000:03:00.0: PCI INT A -> GSI 17 (level, low) ->
IRQ 17
[ 6.076826] iwl3945 0000:03:00.0: setting latency timer to 64
[ 6.080013] xen: registering gsi 17 triggering 0 polarity 1
[ 6.080017] xen_allocate_pirq: returning irq 17 for gsi 17
[ 6.080110] xen: --> irq=17
[ 6.080114] Already setup the GSI :17
[ 6.080200] HDA Intel 0000:00:1b.0: PCI INT B -> GSI 17 (level, low) ->
IRQ 17
[ 6.080310] hda_intel: probe_mask set to 0x1 for device 17aa:20ac
[ 6.080439] HDA Intel 0000:00:1b.0: setting latency timer to 64
[ 6.144802] iwl3945 0000:03:00.0: Tunable channels: 11 802.11bg, 13 802.11a
channels
[ 6.144888] iwl3945 0000:03:00.0: Detected Intel Wireless WiFi Link 3945ABG
[ 6.145099] alloc irq_desc for 745 on node -1
[ 6.145102] alloc kstat_irqs on node -1
[ 6.369741] phy0: Selected rate control algorithm
''iwl-3945-rs''
[ 6.416927] nouveau 0000:01:00.0: power state changed by ACPI to D0
[ 6.417045] nouveau 0000:01:00.0: power state changed by ACPI to D0
[ 6.417131] xen: registering gsi 16 triggering 0 polarity 1
[ 6.417135] xen_allocate_pirq: returning irq 16 for gsi 16
[ 6.417203] xen: --> irq=16
[ 6.417219] Already setup the GSI :16
[ 6.417288] nouveau 0000:01:00.0: PCI INT A -> GSI 16 (level, low) ->
IRQ 16
[ 6.417368] nouveau 0000:01:00.0: setting latency timer to 64
[ 6.420378] [drm] nouveau 0000:01:00.0: failed to evaluate _DSM: 5
[ 6.422847] [drm] nouveau 0000:01:00.0: Detected an NV50 generation card
(0x086900a2)
[ 6.431075] [drm] nouveau 0000:01:00.0: Attempting to load BIOS image from
PRAMIN
[ 6.509683] [drm] nouveau 0000:01:00.0: ... appears to be valid
[ 6.509753] [drm] nouveau 0000:01:00.0: BIT BIOS found
[ 6.509817] [drm] nouveau 0000:01:00.0: Bios version 60.86.3e.00
[ 6.509884] [drm] nouveau 0000:01:00.0: TMDS table revision 2.0 not currently
supported
[ 6.509963] [drm] nouveau 0000:01:00.0: BIT table ''d'' not
found
[ 6.510028] [drm] nouveau 0000:01:00.0: Found Display Configuration Block
version 4.0
[ 6.510108] [drm] nouveau 0000:01:00.0: DCB connector table: VHER 0x40 5 14 2
[ 6.510175] [drm] nouveau 0000:01:00.0: 0: 0x00000040: type 0x40 idx 0 tag
0xff
[ 6.510255] [drm] nouveau 0000:01:00.0: 1: 0x00000100: type 0x00 idx 1 tag
0xff
[ 6.510334] [drm] nouveau 0000:01:00.0: 2: 0x00001231: type 0x31 idx 2 tag
0x07
[ 6.510414] [drm] nouveau 0000:01:00.0: 3: 0x00000311: type 0x11 idx 3 tag
0xff
[ 6.510493] [drm] nouveau 0000:01:00.0: Raw DCB entry 0: 01000323 00010034
[ 6.510560] [drm] nouveau 0000:01:00.0: Raw DCB entry 1: 02811300 00000028
[ 6.510626] [drm] nouveau 0000:01:00.0: Raw DCB entry 2: 02822312 00010030
[ 6.510694] [drm] nouveau 0000:01:00.0: Raw DCB entry 3: 014333f1 0080c080
[ 6.510760] [drm] nouveau 0000:01:00.0: Raw DCB entry 4: 0000000e 00000000
[ 6.510835] [drm] nouveau 0000:01:00.0: Parsing VBIOS init table 0 at offset
0xDD0F
[ 6.555633] [drm] nouveau 0000:01:00.0: Parsing VBIOS init table 1 at offset
0xE04F
[ 6.557084] input: HDA Digital PCBeep as
/devices/pci0000:00/0000:00:1b.0/input/input10
[ 6.592123] [drm] nouveau 0000:01:00.0: Parsing VBIOS init table 2 at offset
0xEAA4
[ 6.592224] [drm] nouveau 0000:01:00.0: Parsing VBIOS init table 3 at offset
0xEB96
[ 6.600172] [drm] nouveau 0000:01:00.0: Parsing VBIOS init table 4 at offset
0xED83
[ 6.600262] [drm] nouveau 0000:01:00.0: Parsing VBIOS init table at offset
0xEDE8
[ 6.624139] [drm] nouveau 0000:01:00.0: 0xEDE8: Condition still not met after
20ms, skipping following opcodes
[ 6.624296] [drm] nouveau 0000:01:00.0: 0xCE7E: parsing output script 0
[ 6.624410] [drm] nouveau 0000:01:00.0: 0xCFF4: parsing output script 0
[ 6.624528] [drm] nouveau 0000:01:00.0: 0xC66A: parsing output script 0
[ 6.749231] [TTM] Zone kernel: Available graphics memory: 1570060 kiB.
[ 6.749324] [drm] nouveau 0000:01:00.0: 128 MiB VRAM
[ 6.783292] [drm] nouveau 0000:01:00.0: 512 MiB GART (aperture)
[ 6.783374] mtrr: type mismatch for e0000000,10000000 old: write-back new:
write-combining
[ 6.783826] [drm] nouveau 0000:01:00.0: Allocating FIFO number 1
[ 6.791136] [drm] nouveau 0000:01:00.0: nouveau_channel_alloc: initialised
FIFO 1
[ 6.792368] [drm] nouveau 0000:01:00.0: Detected a LVDS output
[ 6.792439] [drm] nouveau 0000:01:00.0: Detected a DAC output
[ 6.792504] [drm] nouveau 0000:01:00.0: Detected a TMDS output
[ 6.792610] [drm] nouveau 0000:01:00.0: DCB encoder 1 unknown
[ 6.792684] [drm] nouveau 0000:01:00.0: Detected a LVDS connector
[ 6.891684] [drm] nouveau 0000:01:00.0: Detected a VGA connector
[ 6.891934] [drm] nouveau 0000:01:00.0: Detected a DVI-D connector
[ 8.227492] [drm] nouveau 0000:01:00.0: allocated 1280x800 fb: 0x40250000, bo
ffff880002565200
[ 8.234475] Console: switching to colour frame buffer device 160x50
<------------ Where the kernel still working/booting
[ 8.234492] [drm] nouveau 0000:01:00.0: 0xCE82: parsing output script 1
[ 8.234514] [drm] nouveau 0000:01:00.0: 0xCCE3: parsing clock script 0
[ 8.236884] fb0: nouveaufb frame buffer device
[ 8.236903] registered panic notifier
[ 8.236923] [drm] Initialized nouveau 0.0.15 20090420 for 0000:01:00.0 on
minor 0
[ 8.256422] [drm] nouveau 0000:01:00.0: 0xCE41: parsing clock script 1
[ 9.309417] Adding 3905528k swap on /dev/sda6. Priority:-1 extents:1
across:3905528k
[ 9.871341] loop: module loaded
[ 9.946423] thinkpad_ec: thinkpad_ec 0.40 loaded.
[ 9.954456] tp_smapi 0.40 loading...
[ 9.955726] tp_smapi successfully loaded (smapi_port=0xb2).
[ 10.070906] hdaps: LENOVO ThinkPad R61 detected, setting orientation 1
[ 10.073174] hdaps: initial mode latch is 0x05
[ 10.073388] hdaps: setting ec_rate=250, filter_order=2
[ 10.073625] hdaps: device successfully initialized.
[ 10.074155] input: ThinkPad HDAPS joystick emulation as
/devices/virtual/input/input11
[ 10.076401] input: ThinkPad HDAPS accelerometer data as
/devices/virtual/input/input12
[ 10.076827] hdaps: driver successfully loaded.
[ 13.670764] platform microcode: firmware: requesting intel-ucode/06-0f-0a
[ 13.768157] smapi smapi: set_real_thresh: set start to 49 for bat=0
[ 13.783185] Event-channel device installed.
[ 13.813635] platform microcode: firmware: requesting intel-ucode/06-0f-0a
[ 13.826889] Microcode Update Driver: v2.00
<tigran@aivazian.fsnet.co.uk>, Peter Oruba
[ 13.992164] smapi smapi: set_real_thresh: set stop to 80 for bat=0
[ 14.124860] alloc irq_desc for 744 on node -1
[ 14.124864] alloc kstat_irqs on node -1
[ 14.124937] alloc irq_desc for 743 on node -1
[ 14.124942] alloc kstat_irqs on node -1
[ 14.125279] XENBUS: Unable to read cpu state
[ 14.125713] XENBUS: Unable to read cpu state
[ 20.467473] [drm] nouveau 0000:01:00.0: Allocating FIFO number 2
[ 20.481349] [drm] nouveau 0000:01:00.0: nouveau_channel_alloc: initialised
FIFO 2
[ 22.516816] lp: driver loaded but no devices found
[ 22.668093] ppdev: user-space parallel port driver
[ 24.125298] Bridge firewalling registered
[ 29.117134] iwl3945 0000:03:00.0: firmware: requesting iwlwifi-3945-2.ucode
[ 29.205636] iwl3945 0000:03:00.0: loaded firmware version 15.32.2.9
[ 29.280962] Registered led device: iwl-phy0::radio
[ 29.281683] Registered led device: iwl-phy0::assoc
[ 29.282372] Registered led device: iwl-phy0::RX
[ 29.282993] Registered led device: iwl-phy0::TX
[ 29.298136] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 33.347898] CPU0 attaching NULL sched-domain.
[ 33.347907] CPU1 attaching NULL sched-domain.
[ 33.376194] CPU0 attaching sched-domain:
[ 33.376205] domain 0: span 0-1 level CPU
[ 33.376215] groups: 0 1
[ 33.376238] CPU1 attaching sched-domain:
[ 33.376245] domain 0: span 0-1 level CPU
[ 33.376254] groups: 1 0
[ 35.110003] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 39.497928] Registered led device: iwl-phy0::radio
[ 39.498818] Registered led device: iwl-phy0::assoc
[ 39.499587] Registered led device: iwl-phy0::RX
[ 39.500407] Registered led device: iwl-phy0::TX
[ 39.515441] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 40.334067] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 40.720521] Registered led device: iwl-phy0::radio
[ 40.720674] Registered led device: iwl-phy0::assoc
[ 40.720734] Registered led device: iwl-phy0::RX
[ 40.720793] Registered led device: iwl-phy0::TX
[ 40.742226] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 45.337290] wlan0: direct probe to AP 00:14:bf:89:44:68 (try 1)
[ 45.339838] wlan0: direct probe responded
[ 45.339847] wlan0: authenticate with AP 00:14:bf:89:44:68 (try 1)
[ 45.341910] wlan0: authenticated
[ 45.341963] wlan0: associate with AP 00:14:bf:89:44:68 (try 1)
[ 45.345137] wlan0: RX AssocResp from 00:14:bf:89:44:68 (capab=0x411 status=0
aid=1)
[ 45.345147] wlan0: associated
[ 45.350849] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 45.561573] padlock: VIA PadLock not detected.
[ 50.724196] FAT: utf8 is not a recommended IO charset for FAT filesystems,
filesystem will be case sensitive!
[ 55.872130] wlan0: no IPv6 routers present
-M
Subject: RE: [Xen-users] Issues using nouveau video driver on machine as Dom0
Date: Fri, 14 Jan 2011 13:44:17 -0500
Hello xenners,
It has recently
been brought to my attention that linux-image-2.6.32-5-xen-amd64
(2.6.32-30) was released in the Debian sid repositories [1]. Urgency
is set to high so I''d imagine the migration to squeeze will not take
long as well. The changelog shows [2]:
xen: backport TTM patches to use PCI API. Fixes PCIe GPU (specifically
Radeon and Nouveau) on Xen (Closes: #601341).
Previously I was successful using the nouveau video driver with
Xen on my laptop with nvidia graphic when using the
Debian 2.6.32-29+xen0 kernel from the ianc (Ian Campbells) xenbits
folder.
When I tried the new sid kernel (-30), I
found that I was able to boot natively (bare-metal) with full
functionality; meaning X with gnome desktop manager was working, able
to suspended and woken up, etc. (did not test sound).
When I
tried to boot the kernel through the Xen hypervisor it hangs X &
fb console like reported in a bug report [3]. My laptop is a Lenovo
ThinkPad R61 and my lspci -vvv -s 01:00.0 output is as
followed:
01:00.0 VGA compatible controller: nVidia
Corporation G84M [Quadro NVS 140M] (rev a1) (prog-if 00 [VGA
controller])
Subsystem: Lenovo ThinkPad T61
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+
66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency:
0, Cache Line Size: 64 bytes
Interrupt: pin A
routed to IRQ 16
Region 0: Memory at d6000000
(32-bit, non-prefetchable) [size=16M]
Region 1:
Memory at e0000000 (64-bit, prefetchable) [size=256M]
Region 3: Memory at d4000000 (64-bit, non-prefetchable)
[size=32M]
Region 5: I/O ports at 2000
[size=128]
Expansion ROM at <unassigned>
[disabled]
Capabilities: [60] Power Management
version 2
Flags: PMEClk-
DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0
PME-
Capabilities: [68] MSI: Enable- Count=1/1
Maskable- 64bit+
Address:
0000000000000000 Data: 0000
Capabilities:
[78] Express (v1) Endpoint, MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency
L0s <512ns, L1 <4us
ExtTag+ AttnBtn- AttnInd- PwrInd- RBE+
FLReset-
DevCtl:
Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd+ ExtTag- PhantFunc-
AuxPwr- NoSnoop+
MaxPayload 128 bytes, MaxReadReq 512 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq-
AuxPwr- TransPend-
LnkCap: Port #0, Speed 2.5GT/s, Width x16, ASPM L0s
L1, Latency L0 <512ns, L1 <4us
ClockPM- Surprise- LLActRep- BwNot-
LnkCtl: ASPM L0s Enabled; RCB
128 bytes Disabled- Retrain- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width
x16, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
Capabilities: [100 v1] Virtual Channel
Caps: LPEVC=0 RefClk=100ns PATEntryBits=1
Arb: Fixed- WRR32- WRR64-
WRR128-
Ctrl:
ArbSelect=Fixed
Status:
InProgress-
VC0:
Caps: PATOffset=00 MaxTimeSlots=1
RejSnoopTrans-
Arb: Fixed- WRR32- WRR64- WRR128- TWRR128-
WRR256-
Ctrl: Enable+ ID=0 ArbSelect=Fixed TC/VC=01
Status:
NegoPending- InProgress-
Capabilities: [128 v1]
Power Budgeting <?>
Capabilities: [600
v1] Vendor Specific Information: ID=0001 Rev=1 Len=024 <?>
Kernel driver in use: nouveau
Attached is my dmesg output.
Please advise on how one
should proceed. I''d like to know why 2.6.32-29+xen0 works but
2.6.52-30 does not work on my system.
[1]: http://packages.debian.org/sid/linux-image-2.6.32-5-xen-amd64 or
the source package at http://packages.qa.debian.org/l/linux-2.6.html
[2] :
http://packages.debian.org/changelogs/pool/main/l/linux-2.6/linux-2.6_2.6.32-30/changelog
[3]
:
http://bugs.debian.org/cgi-bin/bugreport.cgi?bug=601341
-M
_______________________________________________
Xen-users mailing list
Xen-users@lists.xensource.com
http://lists.xensource.com/xen-users
Konrad Rzeszutek Wilk
2011-Jan-14 19:16 UTC
[Xen-users] Re: Issues using nouveau driver as Dom0 machine
On Fri, Jan 14, 2011 at 01:28:09PM -0500, Mike Viau wrote:> > > > > > > > > > Hello xenners, > > It has recently > been brought to my attention that linux-image-2.6.32-5-xen-amd64 > (2.6.32-30) was released in the Debian sid repositories [1]. Urgency > is set to high so I''d imagine the migration to squeeze will not take > long as well. The changelog shows [2]: > xen: backport TTM patches to use PCI API. Fixes PCIe GPU (specifically > Radeon and Nouveau) on Xen (Closes: #601341). > > Previously I was successful using the nouveau video driver with > Xen on my laptop with nvidia graphic when using the > Debian 2.6.32-29+xen0 kernel from the ianc (Ian Campbells) xenbits > folder. > > When I tried the new sid kernel (-30), I > found that I was able to boot natively (bare-metal) with full > functionality; meaning X with gnome desktop manager was working, able > to suspended and woken up, etc. (did not test sound). > > When I > tried to boot the kernel through the Xen hypervisor it hangs X & > fb console like reported in a bug report [3]. My laptop is a Lenovo > ThinkPad R61 and my lspci -vvv -s 01:00.0 output is as > followed: > > 01:00.0 VGA compatible controller: nVidia > Corporation G84M [Quadro NVS 140M] (rev a1) (prog-if 00 [VGA > controller]) > Subsystem: Lenovo ThinkPad T61The patches are for PCI-e type cards. Your video card is PCI and goes through a AGP bridge. To get the AGP type support extra backporting from devel/agp.pci-api (git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen.git) would have to be done. _______________________________________________ Xen-users mailing list Xen-users@lists.xensource.com http://lists.xensource.com/xen-users
Mike Viau
2011-Jan-14 20:05 UTC
RE: [Xen-users] Issues using nouveau video driver on machine as Dom0
> On Fri, 14 Jan 2011 14:16:14 -0500 <konrad.wilk@oracle.com> wrote: > > The patches are for PCI-e type cards. Your video card is PCI and > goes through a AGP bridge. To get the AGP type support extra > backporting from devel/agp.pci-api (git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen.git) > would have to be done. >Maybe I have made some mistakes with my hardware configuration (in the BIOS) maybe? Because on http://www.nvidia.com/object/quadro_nvs_notebook_techspecs.html The NVIDIA Quadro NVS 140M is represented as using PCI Express x16 Bus Interface Quoting Wikipedia on the basis of the whole series [1]: "The Nvidia Quadro series of AGP, PCI, and PCI Express graphics-cards comes from the NVIDIA Corporation. " Would the fact that it is a mobile GPU make a difference? According to the reference table on Wikipedia, I found my card again stated as being PCI-E. Quadro chip: NVS 140M Core clock speed (MHz): 400 Memory clock speed (MHz): 600 Memory size: 128 MiB/256 MiB/512 MiB Memory type: 64-bit Memory bandwidth: 9.66 GiB/s CUDA cores: 16 Max. power consumption (W): 10 Interface: PCI Express 3-pin stereo connector: Varies Note: 8400M-GS based[citation needed] I did some digging on information for the NVIDIA 8400M-GS to turn up this: http://www.nvidia.com/object/geforce_8400M.html And again from Wikipedia: GeForce 8M Series On May 10, 2007, NVIDIA announced the availability of their GeForce 8 notebook GPUs through select OEMs. So far the lineup consists of the 8200M, 8400M, 8600M, 8700M and 8800M series chips.[31] It has been announced by nVidia that some of their graphics chips have a higher than expected rate of failure due to overheating when used in particular notebook configurations. Some major laptop manufacturers are making adjustments to fan setting and firmware updates to help delay the occurrence of any potential GPU failure. In late July 2008, Dell released a set of BIOS updates that made the laptop fans spin more frequently.[32] As of mid-August, nVidia is yet to give further details publicly, though it has been heavily rumored that all or most of the 8400 and 8600 cards have this issue. GeForce 8400M Series The GeForce 8400M is the entry level series for the GeForce 8M chipset. Normally found on midrange laptops as an alternate solution to integrated graphics, the 8400M is designed for watching high definition video content rather than gaming. Versions include the 8400M G, 8400M GS, and 8400M GT. While these GPUs are not oriented for high-end gaming, the GDDR3-equipped 8400M-GT can handle most modern games at medium settings,[33] and is suitable for occasional gaming. Both sources do not tell what the bus interface type is, so again I am relatively confident I am using a PCI-E video card. Can I submit any data or additional information to assist in getting my video card compatible with the 2.6.32 branch kernel for use as a dom0 machine? -M _______________________________________________ Xen-users mailing list Xen-users@lists.xensource.com http://lists.xensource.com/xen-users
Konrad Rzeszutek Wilk
2011-Jan-14 20:37 UTC
Re: [Xen-users] Issues using nouveau video driver on machine as Dom0
> Maybe I have made some mistakes with > my hardware configuration (in the BIOS) maybe?No you are totally right. I am mistaken.. .. snip.. Weird thing is that I''ve a: 01:00.0 VGA compatible controller: nVidia Corporation G84 [GeForce 8600 GT] (rev a1) in my main development machine and that works fine (granted I am using a 2.6.37 kernel, but the patches that Ian backported ought to do the trick.)> Can I submit any data or additional information to > assist in getting my video card compatible with the 2.6.32 branch > kernel for use as a dom0 machine?Xen serial log output when the failure happens. You should be able to use the docking station (it has a serial output). Make sure you have the Xen hypervisor logging turned way up and ''drm.debug=255 debug loglevel=10'' to Linux kernel. Look at the PVOPS Wiki for what other options are recommended and how to setp serial access. _______________________________________________ Xen-users mailing list Xen-users@lists.xensource.com http://lists.xensource.com/xen-users