Hi all,
Below is the Vorbis RTP Internet Draft as sent to the AVT working group
of the IETF.
Comments and feedback is still welcomed from the Vorbis community.
Cheers
Phil
---------------------------8<-----------------8<------------------------
Network Working Group Phil Kerr
Internet-Draft The Ogg Vorbis
January 07, 2003 Community / OpenDrama
Expires: July 07, 2003
<p> RTP Payload Format for Vorbis Encoded Audio
<draft-kerr-avt-vorbis-rtp-00.txt>
Status of this Memo
This document is an Internet-Draft and is in full conformance
with all provisions of Section 10 of RFC2026.
Internet-Drafts are working documents of the Internet Engineering
Task Force (IETF), its areas, and its working groups. Note that
other groups may also distribute working documents as
Internet-Drafts.
Internet-Drafts are draft documents valid for a maximum of six
months and may be updated, replaced, or obsoleted by other
documents at any time. It is inappropriate to use Internet-
Drafts as reference material or to cite them other than as
"work in progress".
The list of current Internet-Drafts can be accessed at
http://www.ietf.org/ietf/1id-abstracts.txt
The list of Internet-Draft Shadow Directories can be accessed at
http://www.ietf.org/shadow.html.
The key words "MUST", "MUST NOT", "REQUIRED",
"SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED",
"MAY", and "OPTIONAL" in this
document are to be interpreted as described in RFC 2119 [1].
Copyright Notice
Copyright (C) The Internet Society (2003). All Rights Reserved.
Abstract
This document describes a RTP payload format for transporting
Vorbis encoded audio. It details the encapsulation mechanism for
raw Vorbis data and details the delivery mechanism for the
decoder probability model, referred to as a codebook.
<p><p><p><p><p><p>
Expires July 7, 2003 [Page 1]
Internet Draft draft-kerr-avt-rtp-vorbis-00.txt January 7, 2003
<p>Table of Contents
1. Introduction ........................................ 2
2. Payload Format ...................................... 2
2.1 RTP Header .......................................... 3
2.2 Payload Header ...................................... 4
2.3 Payload Data ........................................ 4
2.4 Example RTP Packet .................................. 5
3. Frame Packetizing ................................... 5
3.1 Example Fragmented Vorbis Packet .................... 6
4. Codebooks ........................................... 7
5. Security Considerations ............................. 8
6. Acknowledgments ..................................... 8
7. References .......................................... 8
8. Full Copyright Statement ............................ 9
9. Authors Address ..................................... 9
1 Introduction
The Xiph.org Foundation creates and defines codecs for use in
multimedia that are not encumbered by patents and thus may be freely
implemented by any individual or organization.
Vorbis is the general purpose multi-channel audio codec created by
the Xiph.org Foundation.
Vorbis encoded audio is generally encapsulated within an Ogg format
bitstream, which provides framing and synchronization. For the
purposes of RTP transport, this layer is unnecessary, and so raw
Vorbis packets are used in the payload.
Vorbis packets are unbounded in length currently. At some future
point there will likely be a practical limit placed on packet
length.
Typical Vorbis packet sizes are from very small (2-3 bytes) to
quite large (8-12 kilobytes). The reference implementation [2]
typically produces packets less than ~800 bytes, except for the
codebooks packet which are ~8-12 kilobytes.
Within a RTP context the maximum Vorbis packet SHOULD be kept below
the MTU size of 1500 octets, including the RTP and payload headers,
to avoid fragmentation.
2 Payload Format
The standard RTP header is followed by an 8 bit payload header,
then the payload data.
<p><p><p><p> Expires July 7,
2003 [Page 2]
Internet Draft draft-kerr-avt-rtp-vorbis-00.txt January 7, 2003
<p>2.1 RTP Header
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|V=2|P|X| CC |M| PT | sequence number |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| timestamp |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| synchronization source (SSRC) identifier |
+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+
| contributing source (CSRC) identifiers |
| ... |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
The RTP header begins with an octet of fields (V, P, X, and CC) to
support specialized RTP uses (see [4] and [5] for details). For
Vorbis RTP applications, V is set to 2, and the P, X, and CC fields
are set to 0.
Marker (M): 1 bit
Set to zero. Audio silence suppression not used. This conforms
to section 4.1 of [6].
Payload Type (PT): 7 bits
An RTP profile for a class of applications is expected to assign
a payload type for this format, or a dynamically allocated
payload type should be chosen which designates the payload as
Vorbis.
Sequence number: 16 bits
The sequence number increments by one for each RTP data packet
sent, and may be used by the receiver to detect packet loss and
to restore packet sequence. This field is detailed further in
[3].
Timestamp: 32 bits
A timestamp representing the sampling time of the first sample of
the first Vorbis packet in the RTP packet. The clock frequency
MUST be set to the sample rate of the encoded audio data and is
conveyed out-of-band.
SSRC/CSRC identifiers:
These two fields, 32 bits each with one SSRC field and a maximum
of 16 CSRC field, are as defined in [3].
<p><p><p><p><p><p><p>
Expires July 7, 2003 [Page 3]
Internet Draft draft-kerr-avt-rtp-vorbis-00.txt January 7, 2003
2.2 Payload Header
The first octet of the payload data is the payload header:
1 2 3 4 5 6 7 8
+---+---+---+---+---+---+---+---+
| C | F | R | # of packets |
+---+---+---+---+---+---+---+---+
C: 1 bit
Set to one if this is a continuation of a fragmented packet.
F: 1 bit
Set to one if the payload contains complete packets or if it
contains the last fragment of a fragmented packet.
R: 1 bit
Reserved, must be set to zero by senders, and ignored by
receivers.
The last 5 bits are the number of complete packets in this payload.
This provides for a maximum number of 32 Vorbis packets in the
payload. If C is set to one, this number should be 0.
2.3 Payload Data
If the payload contains a single Vorbis packet or a Vorbis packet
fragment, the Vorbis packet data follows the payload header.
For payloads which consist of multiple Vorbis packets, payload data
consists of one octet representing the packet length followed by the
packet data for each of the Vorbis packets in the payload.
The Vorbis packet length octet is the length of the data block
minus one.
The payload packing of the Vorbis data packets SHOULD follow the
guidelines set-out in section 4.4 of [6] where the oldest packet
occurs immediately after the RTP packet header.
Channel mapping of the audio is in accordance with BS. 775-1
ITU-R.
<p><p><p><p><p><p><p><p><p><p><p>
Expires July 7, 2003 [Page 4]
Internet Draft draft-kerr-avt-rtp-vorbis-00.txt January 7, 2003
2.4 Example RTP Packet
Here is an example RTP packet containing two Vorbis packets.
RTP Packet Header:
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| 2 |0|0| 0 |0| PT | sequence number |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| timestamp (in sample rate units) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| synchronization source (SSRC) identifier |
+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+
| contributing source (CSRC) identifiers |
| ... |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Payload Data:
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|0|1|0| # pks: 2| len | vorbis data ... |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| ...vorbis data... |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| ... | len | next vorbis packet data... |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
<p>3 Frame Packetizing
Each RTP packet contains either one complete Vorbis packet, one
Vorbis packet fragment, or an integer number of complete Vorbis
packets (upto a max of 32 packets, since the number of packets is
defined by a 5 bit value).
Any Vorbis packet that is larger than 256 octets and less than the
path-MTU should be placed in a RTP packet by itself.
Any Vorbis packet that is 256 bytes or less should be bundled in the
RTP packet with as many Vorbis packets as will fit, up to a maximum
of 32.
If a Vorbis packet will not fit into the RTP packet, it must be
fragmented. A fragmented packet has a zero in the last five bits
of the payload header. Each fragment after the first will also set
the Continued (C) bit to one in the payload header. The RTP packet
containing the last fragment of the Vorbis packet will have the
Marker (F) bit set to one.
<p> Expires July 7, 2003 [Page
5]
Internet Draft draft-kerr-avt-rtp-vorbis-00.txt January 7, 2003
<p>3.1 Example Fragmented Vorbis Packet
Here is an example fragmented Vorbis packet split over three RTP
packets.
RTP packet header details have been excluded from this example.
Packet 1:
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|0|0|0| 0| len | vorbis data ... |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| ...vorbis data... |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
The number of packets field is set to 0.
Packet 2:
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|1|0|0| 0| len | vorbis data ... |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| ...vorbis data... |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
The C bit is set to 1 and the number of packets field is set to 0.
For large Vorbis fragments there can be several of these type of
payload packets. The maximum packet size should be no greater
than the MTU of 1500 octets, including all RTP and payload headers.
Packet 3:
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|1|1|0| 0| len | vorbis data ... |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| ...vorbis data... |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
This is the last Vorbis fragment packet. The C and F bits are
set and the packet count remains set to 0.
<p><p><p><p><p><p>
Expires July 7, 2003 [Page 6]
Internet Draft draft-kerr-avt-rtp-vorbis-00.txt January 7, 2003
<p>4 Codebooks
Unlike other mainstream audio codecs Vorbis has no statically
configured probability model instead it packs all entropy decoding
configuration, VQ and Huffman models into a self-contained
codebook.
To decode a Vorbis stream a codebook is required. These
codebooks are allowed to change for each logical bitstream (for
example, for each song encoded in a radio stream).
The codebooks MUST be completely intact and a client can not decode
a stream with an incomplete or corrupted set.
A client connecting to a multicast RTP Vorbis session needs to get
the first set of codebooks in some manner. These codebooks are
typically between 4 kilobytes and 8 kilobytes in size.
On joining a session the first packet sent MUST be a Vorbis
codebook message.
When codebooks change, or as part of the initial connection phase
a new set are sent as a SR just prior to the Vorbis bitstream
change as an APP defined RTCP message with the 4 octet name field
set to VORC. This is the same format as the initial codebook
packet.
Codebook RTCP packets MUST set the padding (P) flag and add the
appropriate padding octets needed to conform with section 6.6
of [3].
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|V=2|P| subtype | PT=APP=204 | length |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| SSRC/CSRC |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| VORC |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| codebook checksum | codebook ...
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
A 16 bit 1's complement checksum of the codebook precedes the
codebook datablock. This checksum is used to detect a corrupted
codebook. If a checksum failure is detected an empty RR RTCP
message, of APP type with the 4 octet name field set to VORR, is
sent from the client.
<p><p><p><p> Expires July 7,
2003 [Page 7]
Internet Draft draft-kerr-avt-rtp-vorbis-00.txt January 7, 2003
<p> Transmission of the codebook back to the client SHOULD be handled
as an unicast delivery to prevent a rogue client from generating
an excessive number of codebook requests within a multicast stream.
Periodic re-transmission of codebooks midstream SHOULD be catered
for by both client and server at an instance specific frequency
determined by the RTCP overhead.
5 Security Considerations
RTP packets using this payload format are subject to the security
considerations discussed in the RTP specification [3]. This implies
that the confidentiality of the media stream is achieved by using
encryption. Because the data compression used with this payload
format is applied end-to-end, encryption may be performed on the
compressed data.
6 Acknowledgments
This I-D is a continuation of draft-moffitt-vorbis-rtp-00.txt.
Thanks to the Ogg Vorbis Community and to the Xiph.org team,
especially Jack Moffitt <jack@xiph.org>.
7 References
1. Key words for use in RFCs to Indicate Requirement Levels
(RFC 2119).
2. libvorbis: Available from the Xiph website, http://www.xiph.org
3. RTP: A Transport Protocol for Real-Time Applications (RFC 1889).
4. RTP: A transport protocol for real-time applications. Work
in progress, draft-ietf-avt-rtp-new-11.txt.
5. RTP Profile for Audio and Video Conferences with Minimal Control.
Work in progress, draft-ietf-avt-profile-new-12.txt.
<p><p><p><p><p><p><p><p><p><p><p><p><p><p>
Expires July 7, 2003 [Page 8]
Internet Draft draft-kerr-avt-rtp-vorbis-00.txt January 7, 2003
<p>8 Full Copyright Statement
Copyright (C) The Internet Society (2003). All Rights Reserved.
This document and translations of it may be copied and furnished to
others, and derivative works that comment on or otherwise explain it
or assist in its implementation may be prepared, copied, published
and distributed, in whole or in part, without restriction of any
kind, provided that the above copyright notice and this paragraph are
included on all such copies and derivative works. However, this
document itself may not be modified in any way, such as by removing
the copyright notice or references to the Internet Society or other
Internet organizations, except as needed for the purpose of
developing Internet standards in which case the procedures for
copyrights defined in the Internet Standards process must be
followed, or as required to translate it into languages other than
English.
The limited permissions granted above are perpetual and will not be
revoked by the Internet Society or its successors or assigns.
This document and the information contained herein is provided on an
"AS IS" basis and THE INTERNET SOCIETY AND THE INTERNET ENGINEERING
TASK FORCE DISCLAIMS ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING
BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF THE INFORMATION
HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED WARRANTIES OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
<p>9 Authors Address
Phil Kerr
Centre for Music Technology
University of Glasgow
Glasgow, Scotland
UK, G12 8LT
Phone: +44 141 330 5740
Email: philkerr@elec.gla.ac.uk
WWW: http://www.xiph.org/
<p><p><p><p><p><p><p><p><p><p><p><p><p><p><p>---
>8 ----
List archives: http://www.xiph.org/archives/
Ogg project homepage: http://www.xiph.org/ogg/
To unsubscribe from this list, send a message to
'vorbis-dev-request@xiph.org'
containing only the word 'unsubscribe' in the body. No subject is
needed.
Unsubscribe messages sent to the list will be ignored/filtered.